

Trustflight hardware
A small and simple flight controller to be used with the trustflight firmware flight controller firmware, which is focusing on safety by using the Rust programming language.
- Size
- 30.5 × 27 mm
- Copper layers
- 4
- Thickness
- 1.6 mm
- Parts
- 69
- Nets
- 57
- Pads
- 222
- Tracks, vias
- 630, 109
- Pours
- 8
- Routed
- Yes
- KiCad
- KiCad 5 (file 20171130)
- Created
- 30 May 2018
- Updated
- 3 Nov 2018
Overview
Trustflight hardware is an open-source printed circuit board by korken89, from the korken89/trustflight_hardware repository on GitHub. It is a 4-layer board of 30.5 × 27 mm with 69 parts on 57 nets, routed with 630 tracks and 109 vias.
It is built around the STM32F302CBT6, BMP388 and W25X40CLUXIG, with the ISM330DLC, MIC5318-3.3YD5-TR and DMG1013UW among its other parts. Its parts include 26 resistors, 16 capacitors, 10 connectors, 5 ICs and 3 diodes. It belongs with the STM32 boards of this library.
Main components
9STM32F302CBT6
LQFP-48(7x7)-40℃~+85℃ 128KB 12bit 12bit 2V~3.6V 32 Bit 32KB 37 72MHz ARM Cortex-M4 Built-in FLASH LQFP-48(7x7) Microcontrollers (MCU/MPU/SOC) ROHSSTMicroelectronicsMicrocontrollers (MCU/MPU/SOC)BMP388
LGA-10(2x2)-40℃~+85℃ 1.65V~3.6V 1pa/K 2uA 30Kpa~1.25bar 50pa 8pa I2C、SPI LGA-10(2x2) Pressure Sensors ROHSBosch SensortecPressure SensorsW25X40CLUXIG
USON8-EP(2x3)-40℃~+85℃ 100,000 cycles 104MHz 120ms@(32KB) 1uA 2.3V~3.6V 20 Years 400us 4Mbit Hardware write protection、Software write protection、Write enable latch SPI USON8-EP(2x3) NOR FLASH ROHSWinbond ElecNOR FLASHISM330DLC
LGA-14(2.5x3)-40℃~+85℃ 1.71V~3.6V 10uA 16bit 4KB IMU SPI、I2C X,Y,Z X,Y,Z ±16g ±2000dps LGA-14(2.5x3) Accelerometers ROHSSTMicroelectronicsAccelerometersMIC5318-3.3YD5-TR
TSOT-23-5-40℃~+125℃@(Tj) 1 110mV@(300mA) 3.3V 300mA 30uVrms 6V 75dB@(1kHz) 85uA Fixed Over Current Protection、Thermal shutdown、Enable control、Noise bypass terminal Positive TSOT-23-5 Voltage Regulators - Linear, Low Drop Out (LDO) Regulators ROHSMicrochip TechnologyVoltage Regulators - Linear, Low Drop Out (LDO) RegulatorsDMG1013UW
SOT-323-55℃~+150℃ 1 P-Channel 12.07pF 1V 20V 310mW 500mΩ@4.5V 59.76pF 6.36pF 622.4pC@4.5V 820mA P-Channel SOT-323 MOSFETs ROHSDiodes IncorporatedMOSFETsMAF1005GAD352AT000
0402-55℃~+125℃ 1 1.65Ω 270mA 500Ω@100MHz 0402 Ferrite Beads ROHSTDKFerrite BeadsPMEG4005EGWX
SOD-1231 Independent 100uA@40V 10A 40V 470mV@500mA 500mA SOD-123 Schottky Diodes ROHSNexperiaSchottky DiodesSIT8008BI-71-33S-16.000000G
SMD2016-4P-40℃~+85℃ 16MHz 3.3V 4.5mA LVCMOS、HCMOS ±20ppm SMD2016-4P Programmable Oscillators ROHSSiTimeProgrammable Oscillators
README
README.mdThrustFlight hardware reference design
A small and simple flight controller to be used with the trustflight firmware flight controller firmware, which is focusing on safety by using the Rust programming language.
License
The hardware is OSHW using the Cern-OHL license.
Images

Parts
69| Qty | Value | Footprint | References |
|---|---|---|---|
| 12 | 100n | passive:C_0402_1005Metric_Rounded | C1, C2, C3, C4, C5, C7, C10, C12, C13, C14, C15, C16 |
| 10 | 100 | passive:R_0402_1005Metric_Rounded | R1, R2, R3, R4, R5, R12, R19, R21, R22, R23 |
| 10 | 180 | passive:R_0402_1005Metric_Rounded | R8, R9, R10, R13, R14, R15, R16, R17, R18, R25 |
| 6 | Conn_01x02 | Connector_PinHeader_2.54mm:PinHeader_1x02_P2.54mm_Vertical | J1, J2, J3, J4, J6, J7 |
| 4 | 10k | passive:R_0402_1005Metric_Rounded | R7, R20, R24, R26 |
| 4 | Mounting_Hole | MountingHole:MountingHole_2.7mm_M2.5 | MK1, MK2, MK3, MK4 |
| 3 | 4.7u | passive:C_0402_1005Metric_Rounded | C8, C9, C11 |
| 2 | 1k | passive:R_0402_1005Metric_Rounded | R6, R11 |
| 2 | DMG1013UW | sot:SOT-323_SC-70 | Q1, Q2 |
| 1 | 22u | passive:C_0805 | C6 |
| 1 | BMP388 | lga:HLGA-10L-2.0x2.0-BMP388 | U3 |
| 1 | Conn_01x01 | Connector_PinHeader_2.54mm:PinHeader_1x01_P2.54mm_Vertical | J5 |
| 1 | Conn_01x03 | Connector_PinHeader_2.54mm:PinHeader_1x03_P2.54mm_Vertical | J8 |
| 1 | Dronecode_Telemetry | connectors:SM06B-GHS-TB | J10 |
| 1 | ISM330DLC | lga:LGA-14-2.5x3 | U2 |
| 1 | LED_BLUE | passive:D_0603_1608Metric_Rounded | D3 |
| 1 | LED_RED | passive:D_0603_1608Metric_Rounded | D1 |
| 1 | Logo_Open_Hardware_Small | Symbol:OSHW-Symbol_6.7x6mm_SilkScreen | LOGO1 |
| 1 | MAF1005GAD352AT000 | passive:R_0402_1005Metric_Rounded | L1 |
| 1 | MIC5318-3.3YD5 | sot:SOT-23-5 | U5 |
| 1 | PMEG4005EGWX | passive:D_SOD-123 | D2 |
| 1 | SIT8008BI-71-33S-16.000000G | crystals:Crystal_4Pin_2.0x1.6mm | X1 |
| 1 | STM32F302CBT6 | qfp:LQFP-48_7x7mm_Pitch0.5mm | U4 |
| 1 | W25X40CLUXIG | son:USON-8-3x2mm-EP | U1 |
| 1 | swd-4 | connectors:jst-sh-hor-4 | J9 |
Similar boards
- 4 layers34.5 × 56 mm

- 2 layers176 × 55 mm

Nixie clock
jeffkub/nixie-clock
An open source nixie clock with GPS time synchronization.
106 parts2MIT - 4 layers88.5 × 21.5 mm

Hammerhead turret controller backup
alexcwu1121/hammerhead-turret-controller
To build: 1. Install Podman >4.x 2. Install VSCode 3. Install VSCode Dev Containers extension 4. In Dev Containers settings, set the following: - Docker Path: podman - Docker Compose Path: podman-compose - Docker…
103 parts - 6 layers62 × 55.5 mm

Stepper driver
bluesatunsw/owr
This repo includes all software necessary to operate the Test Rover Platform that is being designed and developed in the 502 project.
204 parts5Apache-2.0 - 2 layers102.7 × 40 mm

- 4 layers50 × 70 mm

- 4 layers12 × 34 mm

Altimeter
klownfish/wren-altimeter
A tiny altimeter for 18mm rockets. Assembled by JLCPCB and written in Rust
40 parts - 2 layers42.7 × 48.8 mm

Duct turbo fan controller v4
scattym/kicad-duct-turbo-fan-controller
Fan controller projects for the duct turbo, terrabloom and ac infinity fans
46 parts4GPL-3.0
Questions
How big is the Trustflight hardware PCB?
It measures 30.5 × 27 mm and has 4 copper layers, 1.6 mm thick.
What parts does the Trustflight hardware use?
69 parts, built around the STM32F302CBT6, BMP388, W25X40CLUXIG and ISM330DLC. The full list of its parts is on this page, with links to each part's symbol and footprint where PCBKit's library has them.
Where can I download the Trustflight hardware KiCad files?
From the korken89/trustflight_hardware repository on GitHub, at the commit this page was made from: the board is trustflight_hardware.kicad_pcb. PCBKit opens the board in the browser, with nothing to install.
Can I use the Trustflight hardware design in my own project?
Its repository states no licence, so its author keeps all rights: ask korken89 before reusing the design.