Skip to the content
PCBKitNew board
LPS22HH on a board, in 3D

LPS22HH

STMicroelectronics

-40℃~+85℃ 0.025hpa 0.5hpa 1.7V~3.6V 26Kpa~1.26bar 900nA I2C、SPI On-chip temperature compensation、Integrated ADC and digital interface、On-chip calibration and non-volatile storage、Integrated signal amplifier、On-chip temperature output HLGA-10(2x2) Pressure Sensors ROHS

Extended
DatasheetJLCPCBLCSCst/LPS22HH
Category
Pressure Sensors
Package
HLGA-10(2x2)
Pins
10

Overview

The LPS22HH is a pressure Sensor made by STMicroelectronics in a HLGA-10(2x2) package with 10 pins. -40℃~+85℃ 0.025hpa 0.5hpa 1.7V~3.6V 26Kpa~1.26bar 900nA I2C、SPI On-chip temperature compensation、Integrated ADC and digital interface、On-chip calibration and non-volatile storage、Integrated signal amplifier、On-chip temperature output HLGA-10(2x2) Pressure Sensors ROHS.

PCBKit's library has its KiCad symbol (Sensor_Pressure:LPS22HH, from KiCad's library) and its footprint (Package_LGA:ST_HLGA-10_2x2mm_P0.5mm_LayoutBorder3x2y, from KiCad's library), ready for a KiCad board. 6 are in stock at JLCPCB (part C2827824). 19 open-source boards in 15 repositories on GitHub use it.

Symbol

Vdd_IO1SCL2SDA4SA05CS6INT_DRDY7GND8VDD10
Sensor_Pressure:LPS22HHFrom KiCad's library

Footprint

12345678910
Package_LGA:ST_HLGA-10_2x2mm_P0.5mm_LayoutBorder3x2yFrom KiCad's library

From the datasheet

10
Supply, least
1.7 V · VDD, recommended operating, min · p. 10
Supply, most
3.6 V · VDD, recommended operating, max · p. 10
Supply, least
1.7 V · Vdd_IO, recommended operating, min · p. 10
Supply, absolute maximum
4.8 V · Vdd, absolute maximum · p. 13
Supply, absolute maximum
4.8 V · Vdd_IO, absolute maximum · p. 13
Works from
-40 °C · operating ambient temperature, min · p. 1
Works up to
85 °C · operating ambient temperature, max · p. 1
Takes working
4 µA · low-current mode, ODR = 1 Hz, VDD = 1.8 V, 25 °C, typical · p. 46
Takes working
12 µA · low-noise mode, ODR = 1 Hz, VDD = 1.8 V, 25 °C, typical · p. 46
Takes asleep
900 nA · power-down mode, VDD = 1.8 V, 25 °C, typical · p. 10

Parameters

10
Absolute Accuracy
0.5hpa
Current - Supply
4uA
Features
On-chip temperature output
Interface
I2C
Operating Temperature
-40℃~+85℃
Pressure range
26Kpa~1.26bar
Relative Accuracy
0.025hpa
Standby Current
900nA
Voltage - Supply
1.7V~3.6V
Voltage - Supply(Absolute Max)
4.8V

Order codes

1

Pinout

10
The pins of the LPS22HH
PinNameType
1Vdd_IOPower in
2SCLInput
3GNDPassive
4SDAInput/output
5SA0Input
6CSInput
7INT_DRDYOutput
8GNDPower in
9GNDPassive
10VDDPower in

Open-source boards using it

All 19
  • 4 layers36 × 36 mmOpenuav, the printed circuit board in 3D

    Openuav

    catphish/openuav

    An open source unmanned aerial vehicle

    80 parts12MIT
  • 2 layers43 × 43 mmIec62386-panel, the printed circuit board in 3D

    Iec62386-panel

    peterisza/iec62386-wall-panel

    Wall panel for smart homes. 2 wires, no polarity, arbitrary bus topology, exchangeable front panel with hardware capacitive buttons, temperature+humidity+pressure+CO2.

    64 parts2
  • 8 layers50 × 50 mm89 pitot s3, the printed circuit board in 3D

    89 pitot s3

    CREATE-ROCKET/Avi_89J_Pitot_log

    61 parts1
  • 4 layers100 × 100 mmCentral ECU, the printed circuit board in 3D

    Central ECU

    UC-Aerospace/Hybrid25_ECU

    The central ECU is pretty simple and carries out a couple of tasks. Firstly is comms which is easy to see with CAN on the left and RS422 on the right of the schematic.

    180 parts1
  • 4 layers40.8 × 40.8 mmACwing FC A, the printed circuit board in 3D

    ACwing FC A

    ACwing-UAV/ACwing_HW

    ACwing is a modular set of PCBs for small multirotors.

    111 parts
  • 4 layers96 × 81 mmSensor hub, the printed circuit board in 3D

    Sensor hub

    Aifryz/sensor-hub

    126 partsMIT
  • 2 layersDrone controller, the printed circuit board in 3D

    Drone controller

    C-monC/Drone-simluation

    Experimenting with reinforcement learning for drone control.

    12 parts
  • 4 layers55.9 × 30.5 mmVanguard, the printed circuit board in 3D

    Vanguard

    Frostydev-Avionics/Vanguard-PCB

    82 partsGPL-2.0

Show this part on your page

A live frame, for any web page
<iframe src="https://pcbkit.io/embed/parts/st/LPS22HH" title="LPS22HH in PCBKit" width="100%" height="480" style="border:0;border-radius:12px" allow="fullscreen" loading="lazy"></iframe>
A picture
<img src="https://pcbkit.io/embed/parts/st/LPS22HH.jpg" alt="LPS22HH" width="1200" height="900">
A picture that opens the part, for a README
[![LPS22HH](https://pcbkit.io/embed/parts/st/LPS22HH.jpg?size=s)](https://pcbkit.io/parts/st/LPS22HH)

Questions

Is there a KiCad symbol and footprint for the LPS22HH?

Yes. The symbol is Sensor_Pressure:LPS22HH and the footprint Package_LGA:ST_HLGA-10_2x2mm_P0.5mm_LayoutBorder3x2y, both drawn on this page. PCBKit places them on a board for you when you design with it.

What package is the LPS22HH?

HLGA-10(2x2), with 10 pins. Its footprint is drawn on this page.

Where is the LPS22HH datasheet?

STMicroelectronics publishes it: the Datasheet link on this page opens it.

Where can I order the LPS22HH?

JLCPCB lists it as part C2827824, with 6 in stock; the sellers' links on this page open their listings.

What can replace the LPS22HH?

Parts like it in the library: the LPS22HB by STMicroelectronics, the LPS22DF by STMicroelectronics and the LPS22HHQ by STMicroelectronics. Check their datasheets: a part that fits the footprint may still differ in its ratings.

Which open-source boards use the LPS22HH?

19 boards in 15 repositories on GitHub; the most starred are listed on this page, with their KiCad files.

Parts like it

3