2 layers
Drone controller
C-monC/Drone-simluation
Experimenting with reinforcement learning for drone control.
12 parts
4 layers96 × 81 mm
Sensor hub
Aifryz/sensor-hub- Size
- 96 × 81 mm
- Copper layers
- 4
- Thickness
- 1.61 mm
- Parts
- 126
- Nets
- 110
- Pads
- 483
- Tracks, vias
- 1,424, 470
- Pours
- 21
- Routed
- Yes
- KiCad
- KiCad 8.0 (file 20240108)
- Created
- 3 Dec 2022
- Updated
- 18 Aug 2026
Overview
Sensor hub is an open-source printed circuit board by Aifryz, from the Aifryz/sensor-hub repository on GitHub, published under the MIT licence. It is a 4-layer board of 96 × 81 mm with 126 parts on 110 nets, routed with 1,424 tracks and 470 vias.
It is built around the LPS22HH, PCAL6408ABSHP and SCD40-D-R2, with the SI7021-A20-GM, AMS1117-3.3 and W5500 among its other parts. Its parts include 46 capacitors, 38 resistors, 10 connectors, 8 ICs and 4 diodes. It belongs with the sensors and measurement boards and the STM32 boards of this library.
Main components
6
LPS22HH
HLGA-10(2x2)-40℃~+85℃ 0.025hpa 0.5hpa 1.7V~3.6V 26Kpa~1.26bar 900nA I2C、SPI On-chip temperature compensation、Integrated ADC and digital interface、On-chip calibration and non-volatile storage、Integrated signal amplifier、On-chip temperature output HLGA-10(2x2) Pressure Sensors ROHSSTMicroelectronicsPressure Sensors
PCAL6408ABSHP
HVQFN-16-EP(3x3)-40℃~+85℃ 1.65V~5.5V 1uA 2 25mA 25mA 400kHz 8 I2C、SMBus Interrupt Output Push-Pull、Open-drain Reset function、Cascading and address extension、Built-in LED driver、IO level configurable HVQFN-16-EP(3x3) I/O Expanders ROHSNXP SemiconductorsI/O Expanders
SCD40-D-R2
LGA-20(10.1x10.1)-10℃~+60℃ 10.1mm 10.1mm 15mA 2.4V~5.5V 400ppm~2000ppm 6.5mm Air quality I2C Reset function ±5% LGA-20(10.1x10.1) Gas Sensors ROHSSensirionGas Sensors
SI7021-A20-GM
DFN-6-EP(3x3)DFN-6-EP(3x3) Temperature and Humidity Sensor ROHSSilicon LabsTemperature And Humidity Sensor
AMS1117-3.3
SOT-223-40℃~+125℃ 0.003%Vout 1 1.1V@(800mA) 15V 1A 3.3V 5mA 72dB@(120Hz) Fixed Over Current Protection、Short Circuit Protection、Thermal shutdown Positive SOT-223 Voltage Regulators - Linear, Low Drop Out (LDO) Regulators ROHSAdvanced Monolithic SystemsVoltage Regulators - Linear, Low Drop Out (LDO) Regulators
W5500
LQFP-48_7x7-40℃~+85℃ 10BASE-T、100BASE-TX 3.3V 32KB SPI SPI Wake-up function、Programmable LED indication、Low-power mode Yes LQFP-48(7x7) Ethernet Controllers ROHSWIZNETEthernet Controllers
README
README.mdsensor-hub
Parts
126| Qty | Value | Footprint | References |
|---|---|---|---|
| 17 | 100n | Capacitor_SMD:C_0603_1608Metric | C10, C11, C12, C14, C16, C18, C19, C20, C21, C22, C27, C28, C33, C34, C35, C43 +1 |
| 10 | 10n | Capacitor_SMD:C_0603_1608Metric | C1, C5, C29, C30, C31, C32, C38, C39, C40, C41 |
| 9 | 4.7k | Resistor_SMD:R_0603_1608Metric | R21, R22, R23, R24, R25, R26, R27, R33, R34 |
| 5 | 22u | Capacitor_SMD:C_0805_2012Metric | C24, C25, C42, C45, C46 |
| 5 | 47k | Resistor_SMD:R_0603_1608Metric | R15, R16, R17, R18, R19 |
| 4 | 0R | Resistor_SMD:R_0603_1608Metric | R14, R30, R36, R37 |
| 4 | 3.3R | Resistor_SMD:R_0603_1608Metric | R2, R3, R4, R5 |
| 4 | 49R9 | Resistor_SMD:R_0603_1608Metric | R6, R7, R8, R9 |
| 4 | MountingHole | MountingHole:MountingHole_3mm | H1, H2, H3, H4 |
| 4 | ~ | Jumper:SolderJumper-3_P1.3mm_Bridged12_RoundedPad1.0x1.5mm | JP1, JP2, JP3, JP4 |
| 3 | 10u | Capacitor_SMD:C_0805_2012Metric | C15, C17, C44 |
| 3 | 1k | Resistor_SMD:R_0603_1608Metric | R20, R29, R38 |
| 3 | 4.7u | Capacitor_SMD:C_0603_1608Metric | C2, C8, C13 |
| 3 | LED | LED_SMD:LED_0603_1608Metric | D2, D3, D4 |
| 2 | 10k | Resistor_SMD:R_0603_1608Metric | R28, R35 |
| 2 | 18n | Capacitor_SMD:C_0603_1608Metric | C36, C37 |
| 2 | 330R | Resistor_SMD:R_0603_1608Metric | R31, R32 |
| 2 | 6.8n | Capacitor_SMD:C_0603_1608Metric | C3, C4 |
| 2 | TestPoint | TestPoint:TestPoint_Pad_D1.0mm | TP1, TP2 |
| 1 | 100-2000R@100MHz | Inductor_SMD:L_0603_1608Metric | FB1 |
| 1 | 10R | Resistor_SMD:R_0603_1608Metric | R10 |
| 1 | 12.4k 1% | Resistor_SMD:R_0603_1608Metric | R1 |
| 1 | 16MHz | Crystal:Crystal_SMD_SeikoEpson_TSX3225-4Pin_3.2x2.5mm | Y3 |
| 1 | 1M | Resistor_SMD:R_0603_1608Metric | R11 |
| 1 | 1nF/2kV | Capacitor_SMD:C_1206_3216Metric | C7 |
| 1 | 1u | Capacitor_SMD:C_0603_1608Metric | C26 |
| 1 | 2.2u | Inductor_SMD:L_APV_ANR5045 | L1 |
| 1 | 22n | Capacitor_SMD:C_0603_1608Metric | C6 |
| 1 | 22pF | Capacitor_SMD:C_0603_1608Metric | C23 |
| 1 | 25MHz | Crystal:Crystal_SMD_SeikoEpson_TSX3225-4Pin_3.2x2.5mm | Y1 |
| 1 | 32.768kHz | Crystal:Crystal_SMD_3215-2Pin_3.2x1.5mm | Y2 |
| 1 | 330k | Resistor_SMD:R_0603_1608Metric | R12 |
| 1 | 600R@100MHz | Inductor_SMD:L_0603_1608Metric | FB2 |
| 1 | 75k | Resistor_SMD:R_0603_1608Metric | R13 |
| 1 | AMS1117-3.3 | Package_TO_SOT_SMD:SOT-223-3_TabPin2 | U6 |
| 1 | AP3402 | Package_TO_SOT_SMD:TSOT-23-6 | U3 |
| 1 | BATT | Battery:BatteryHolder_MYOUNG_BS-07-A1BJ001_CR2032 | J10 |
| 1 | Conn_ARM_JTAG_SWD_10 | Connector_PinHeader_1.27mm:PinHeader_2x05_P1.27mm_Vertical_SMD | J1 |
| 1 | ENC_CONN | Connector_TE-Connectivity:TE_Micro-MaTch_215079-4_2x02_P1.27mm_Vertical | J6 |
| 1 | I2C_CONN | Connector_PinHeader_2.54mm:PinHeader_1x04_P2.54mm_Vertical | J9 |
| 1 | LCD_CONN | Connector_TE-Connectivity:TE_Micro-MaTch_1-215079-0_2x05_P1.27mm_Vertical | J5 |
| 1 | LED_BGRA | LED_SMD:LED_Cree-PLCC4_3.2x2.8mm_CCW | D1 |
| 1 | LPS22HH | Package_LGA:ST_HLGA-10_2x2mm_P0.5mm_LayoutBorder3x2y | U7 |
| 1 | Micro_SD_Card_Det2 | sensor-hub-footprints:MicroSD_Det2 | J2 |
| 1 | PCAL6408ABS | Package_DFN_QFN:QFN-16-1EP_3x3mm_P0.5mm_EP1.45x1.45mm | U4 |
| 1 | PWR | Connector_PinHeader_2.54mm:PinHeader_1x02_P2.54mm_Vertical | J4 |
| 1 | RADIO_CONN | Connector_TE-Connectivity:TE_Micro-MaTch_215079-8_2x04_P1.27mm_Vertical | J7 |
| 1 | RJ45_Wuerth_7499010121A | Connector_RJ:RJ45_Wuerth_7499010121A_Horizontal | J3 |
| 1 | SCD40-D-R2 | Sensor:Sensirion_SCD4x-1EP_10.1x10.1mm_P1.25mm_EP4.8x4.8mm | U5 |
| 1 | STM32F411CEUx | Package_DFN_QFN:QFN-48-1EP_7x7mm_P0.5mm_EP5.6x5.6mm | U1 |
| 1 | SW_Push | Button_Switch_SMD:SW_SPST_CK_RS282G05A3 | SW1 |
| 1 | Si7021-A20 | Package_DFN_QFN:DFN-6-1EP_3x3mm_P1mm_EP1.5x2.4mm | U8 |
| 1 | SolderJumper_3_Open | Jumper:SolderJumper-3_P1.3mm_Open_RoundedPad1.0x1.5mm | JP5 |
| 1 | UART_CONN | Connector_PinHeader_2.54mm:PinHeader_1x03_P2.54mm_Vertical | J8 |
| 1 | W5500 | Package_QFP:LQFP-48_7x7mm_P0.5mm | U2 |
The 124 most common of 126 parts.
Questions
How big is the Sensor hub PCB?
It measures 96 × 81 mm and has 4 copper layers, 1.61 mm thick.
What parts does the Sensor hub use?
126 parts, built around the LPS22HH, PCAL6408ABSHP, SCD40-D-R2 and SI7021-A20-GM. The full list of its parts is on this page, with links to each part's symbol and footprint where PCBKit's library has them.
Where can I download the Sensor hub KiCad files?
From the Aifryz/sensor-hub repository on GitHub, at the commit this page was made from: the board is hardware/sensor-hub/sensor-hub.kicad_pcb and its schematic hardware/sensor-hub/mcu.kicad_sch. PCBKit opens the board in the browser, with nothing to install.
Can I use the Sensor hub design in my own project?
Its repository publishes it under the MIT licence: you may reuse it on that licence's terms (keep the author's notice, and for a copyleft licence share your changes alike).
Similar boards
- 4 layers130 × 105 mm
HomeDeck
Kilan777/HomeDeck
Jarvis HomeDeck: a Raspberry Pi CM4 carrier board and voice-assistant software for a 7-inch smart display (KiCad hardware, generated from Python, plus the Python/JS assistant)
228 parts1 - 4 layers44.5 × 22.5 mm
- 4 layers124.9 × 103.9 mm
- 4 layers36 × 36 mm
- 2 layers43 × 43 mm
Iec62386-panel
peterisza/iec62386-wall-panel
Wall panel for smart homes. 2 wires, no polarity, arbitrary bus topology, exchangeable front panel with hardware capacitive buttons, temperature+humidity+pressure+CO2.
64 parts2 - 8 layers50 × 50 mm
- 4 layers100 × 100 mm
Central ECU
UC-Aerospace/Hybrid25_ECU
The central ECU is pretty simple and carries out a couple of tasks. Firstly is comms which is easy to see with CAN on the left and RS422 on the right of the schematic.
180 parts1