4 layers84.3 × 50.8 mm
PrecisionTimer RevG
SepticElectronics/High-Speed-Timer
High Speed Precision Timer 55ps/4ns
125 partsGPL-3.0
4 layers84.3 × 50.8 mm
PrecisionTimer RevG-1
SepticElectronics/High-Speed-TimerHigh Speed Precision Timer 55ps/4ns
- Size
- 84.3 × 50.8 mm
- Copper layers
- 4
- Thickness
- 1.6 mm
- Parts
- 128
- Nets
- 163
- Pads
- 491
- Tracks, vias
- 1,163, 364
- Pours
- 48
- Routed
- Yes
- KiCad
- KiCad 5 (file 20171130)
- Created
- 25 Jul 2020
- Updated
- 29 Sep 2020
Overview
PrecisionTimer RevG-1 is an open-source printed circuit board by SepticElectronics, from the SepticElectronics/High-Speed-Timer repository on GitHub, published under the GPL-3.0 licence. It is a 4-layer board of 84.3 × 50.8 mm with 128 parts on 163 nets, routed with 1,163 tracks and 364 vias.
It is built around the LCMXO2-256HC-6SG32C, MIC23050-4YML-TR and MIC23050-SYML-TR, with the TS30012-M050QFNR, VNC2-32Q1C-REEL and MIC2095-2YMT-TR among its other parts. Its parts include 43 capacitors, 15 resistors, 10 ICs, 9 connectors and 5 crystals. It belongs with the fPGA and programmable logic boards and the SAM D and SAM and FPGA and CPLD boards of this library.
Main components
10
LCMXO2-256HC-6SG32C
QFN-32-EP(5x5)0℃~+85℃ 2.375V~3.465V 21 256 32 MachXO2 Supports hot swap、Supports watchdog timeout detection QFN-32-EP(5x5) Programmable Logic Device (CPLDs/FPGAs) ROHSLatticeProgrammable Logic Device (CPLDs/FPGAs)
MIC23050-4YML-TR
MLF-8(2x2)-40℃~+125℃ 1 1.2V 2.7V~5.5V 20uA 4MHz 600mA Buck Buck Built-in Fixed Yes MLF-8(2x2) DC-DC Converters ROHSMicrochip TechnologyDC-DC ConvertersMIC23050-SYML-TR
TDFN-8-EP(2x2)-40℃~+125℃@(TJ) 1 2.7V~5.5V 20uA 3.3V 4MHz 600mA Buck Built-in Fixed Light load efficient mode Step-down type Yes TDFN-8-EP(2x2) DC-DC Converters ROHSMicrochip TechnologyDC-DC Converters
TS30012-M050QFNR
QFN-16-EP(3x3)-40℃~+125℃@(TJ) 1 1MHz 2A 3.3mA 4.5V~24V 5V Buck Built-in Fixed Overcurrent Protection、Light load efficient mode、Operating status indication、Cycle-by-cycle current limiting Step-down type Yes QFN-16-EP(3x3) DC-DC Converters ROHSSEMTECHDC-DC Converters
VNC2-32Q1C-REEL
QFN-32-EP(7x7)-40℃~+85℃@(Ta) 3.3V Controller QFN-32-EP(7x7) USB Converters ROHSFTDIUSB Converters
MIC2095-2YMT-TR
UDFN-6-40℃~+85℃ 0.5A 2.5V~5.5V Overcurrent Protection、Operating status indication UDFN-6 Power Distribution Switches ROHSMicrochip TechnologyPower Management - Specialized
LM74610QDGKTQ1
VSSOP-8-0.65mmVSSOP-8-0.65mm ORing Controllers ROHSTexas InstrumentsAC-DC Controllers And Regulators
TDC7200PW
TSSOP-14-40℃~+85℃ 0.5uA 20MHz 2V~3.6V SPI TSSOP-14 ADCs/DACs - Special Purpose ROHSTexas InstrumentsADCs/DACs - Special Purpose
ECS-160-8-36B-CKY-TR
SMD2520-4P-30℃~+85℃ 16MHz 70Ω 8pF ±10ppm ±10ppm SMD2520-4P Crystals ROHSECSCrystalsDSC1001DI2-125.0000
SMD2520-4P-40℃~+85℃ 1.8V~3.3V 125MHz 8.7mA CMOS ±25ppm SMD2520-4P Programmable Oscillators ROHSMicrochip TechnologyProgrammable Oscillators
README
README.mdHigh Speed Precision Timer SEHSPT554
A simple digital timer based on the TDC7200 for high-precision, short burst time measurement with a resolution of up to 55 ps. Long interval, low precision time measurement is done using a 125 MHz oscillator and a DDR-type clocked synchronous counter, implemented in a MachXO2 FPGA with a theoretical resolution of 4 ns. The data collection and interfacing is handled by an ATSAM4S Microcontroller. Two USB 2.0 and a MicroSD Interface are available for data collection.
If connected to a PC via USB-B the device is fully USB-Bus-powered. In the case of only using a microSD-Card or a USB thumb drive, the device must be powered from a 6-24 V Barrel Connector (5.5 x 2.1 mm or 5.5 x 2.5 mm, Center Positive).
A MIPI10 JTAG programming header is available and can be used for reprogramming the FPGA or for a boundary scan of both the FPGA and the MCU. A 4-Pin (2.54 mm) UART connector is provided for reprogramming the MCU. Three SMA connectors are used with 3.3 V LVCMOS signal-level for triggering and resetting the measurements.
The PCB is designed to fit inside the Thorlabs EEB3311 housing.
This project started out as a Product Design / Layout challenge for myself and is still in a very early WIP-stage. Any (constructive) input is very much appreciated. Please note that all of the mentioned features are purely implemented on a PCB / Schematic level. No software, except for the FPGA configuration, has been written yet.
Parts
128| Qty | Value | Footprint | References |
|---|---|---|---|
| 19 | 100n | Capacitor_SMD:C_0603_1608Metric | C3, C10, C14, C18, C19, C20, C21, C22, C23, C24, C25, C26, C27, C35, C36, C37 +3 |
| 12 | TestPoint_Alt | TestPoint:TestPoint_Pad_D1.0mm | TP2, TP4, TP7, TP8, TP9, TP10, TP11, TP16, TP17, TP18, TP19, TP20 |
| 10 | 4µ7 | Capacitor_SMD:C_0603_1608Metric | C6, C7, C9, C12, C17, C29, C31, C33, C34, C43 |
| 10 | TestPoint_Alt | Selfmade Stuff:TestPoint_Pad_D0.7mm | TP1, TP3, TP5, TP6, TP12, TP13, TP14, TP15, TP21, TP22 |
| 6 | 10p | Capacitor_SMD:C_0402_1005Metric | C1, C2, C4, C5, C40, C41 |
| 6 | Ferrite 2A 330R | Inductor_SMD:L_0603_1608Metric | FB1, FB2, FB3, FB4, FB5, FB6 |
| 5 | 10k | Resistor_SMD:R_0603_1608Metric | R5, R6, R7, R8, R14 |
| 3 | 0R | Resistor_SMD:R_0603_1608Metric | R9, R10, R13 |
| 3 | 22µ | Capacitor_SMD:C_0805_2012Metric | C15, C16, C32 |
| 3 | 47k | Resistor_SMD:R_0402_1005Metric | R1, R2, R3 |
| 3 | Conn_Coaxial | Connector_Coaxial:SMA_Molex_73251-2200_Horizontal | J7, J8, J9 |
| 2 | 1µH | Inductor_SMD:L_0805_2012Metric | L1, L2 |
| 2 | 4.7µH | Inductor_SMD:L_0805_2012Metric | L3, L4 |
| 2 | 560p | Capacitor_SMD:C_0603_1608Metric | C11, C28 |
| 2 | ECS-160-8-36B-CKY-TR | Crystal:Crystal_SMD_2520-4Pin_2.5x2.0mm | X1, X5 |
| 2 | MIC2095-2YMT-TR | SamacSys_Parts:SON50P160X160X60-7N-D | U9, U10 |
| 2 | Polyfuse 500 mA | Fuse:Fuse_1206_3216Metric_Castellated | F1, F2 |
| 1 | 100k | Resistor_SMD:R_0603_1608Metric | R15 |
| 1 | 100p | Capacitor_SMD:C_0603_1608Metric | C38 |
| 1 | 100µ | Capacitor_SMD:C_1206_3216Metric | C30 |
| 1 | 10µ | Capacitor_SMD:C_0805_2012Metric | C13 |
| 1 | 1k | Resistor_SMD:R_0603_1608Metric | R4 |
| 1 | 22R | Resistor_SMD:R_0603_1608Metric | R11 |
| 1 | 68R | Resistor_SMD:R_0603_1608Metric | R12 |
| 1 | ATSAM4S2 | Package_BGA:TFBGA-100_9.0x9.0mm_Layout10x10_P0.8mm | U4 |
| 1 | Barrel_Jack_Switch | Connector_BarrelJack:BarrelJack_Wuerth_6941xx301002 | J3 |
| 1 | Conn_01x04_Male | Connector_PinHeader_2.54mm:PinHeader_1x04_P2.54mm_Vertical_SMD_Pin1Left | J6 |
| 1 | Conn_02x05_Odd_Even | Connector_PinHeader_1.27mm:PinHeader_2x05_P1.27mm_Vertical_SMD | J5 |
| 1 | D1213A-02SO-7 | Selfmade Stuff:SOT-26 | D4 |
| 1 | DSC1001DI2-125.0000 | Oscillator:Oscillator_SMD_SeikoEpson_SG210-4Pin_2.5x2.0mm | X2 |
| 1 | ECS-3225S33-160-FN-TR | Oscillator:Oscillator_SMD_EuroQuartz_XO32-4Pin_3.2x2.5mm | X4 |
| 1 | FC-135 32.7680KA-AG0 | Crystal:Crystal_SMD_3215-2Pin_3.2x1.5mm | X3 |
| 1 | LCMXO2-256HC-6SG32C | SamacSys_Parts:QFN50P500X500X60-33N | U2 |
| 1 | LED | LED_THT:LED_D3.0mm | D1 |
| 1 | LM74610QDGKTQ1 | SamacSys_Parts:SOP65P490X110-8N | U8 |
| 1 | LOGO | Selfmade Stuff:CreativeCommons_CC_6mm | G*** |
| 1 | MIC23050-4YML-TR | SamacSys_Parts:SON50P200X200X90-9N | U7 |
| 1 | MIC23050-SYML-TR | SamacSys_Parts:SON50P200X200X90-9N | U6 |
| 1 | Micro_SD_Card | Selfmade Stuff:475710001 | J4 |
| 1 | NMOS 2A | Package_TO_SOT_SMD:SOT-23 | Q1 |
| 1 | TDC7200PW | SamacSys_Parts:SOP65P640X120-14N | U1 |
| 1 | TS30012-M050QFNR | SamacSys_Parts:QFN50P300X300X100-17N-D | U5 |
| 1 | TVS 28V | Diode_SMD:D_SMB | D2 |
| 1 | USB_A | Connector_USB:USB_A_Molex_67643_Horizontal | J2 |
| 1 | USB_B | SamacSys_Parts:KUSBEXSMTBS1NBTR | J1 |
| 1 | VNC2-32Q1C-REEL | SamacSys_Parts:QFN65P700X700X90-33N-D | U3 |
| 1 | Zener 5.6V | Diode_SMD:D_MiniMELF | D3 |
The 122 most common of 128 parts.
Questions
How big is the PrecisionTimer RevG-1 PCB?
It measures 84.3 × 50.8 mm and has 4 copper layers, 1.6 mm thick.
What parts does the PrecisionTimer RevG-1 use?
128 parts, built around the LCMXO2-256HC-6SG32C, MIC23050-4YML-TR, MIC23050-SYML-TR and TS30012-M050QFNR. The full list of its parts is on this page, with links to each part's symbol and footprint where PCBKit's library has them.
Where can I download the PrecisionTimer RevG-1 KiCad files?
From the SepticElectronics/High-Speed-Timer repository on GitHub, at the commit this page was made from: the board is PrecisionTimer_RevG.1/PCB Design Files/PrecisionTimer_RevG-1.kicad_pcb. PCBKit opens the board in the browser, with nothing to install.
Can I use the PrecisionTimer RevG-1 design in my own project?
Its repository publishes it under the GPL-3.0 licence: you may reuse it on that licence's terms (keep the author's notice, and for a copyleft licence share your changes alike).
More from SepticElectronics/High-Speed-Timer
3- 4 layers84.3 × 50.8 mm
PrecisionTimer RevF
SepticElectronics/High-Speed-Timer
High Speed Precision Timer 55ps/4ns
115 partsGPL-3.0 - 4 layers84.3 × 50.8 mm
PrecisionTimer RevF back
SepticElectronics/High-Speed-Timer
High Speed Precision Timer 55ps/4ns
111 partsGPL-3.0
Similar boards
- 4 layers65 × 56.5 mm
2019-07-03 17:28:54 fpga hat
Wren6991/Snowflake-FPGA
A cheap iCE40 development board, designed on and for Raspberry Pi
90 parts31 - 4 layers90.5 × 67 mm
AS 4
beaked99/air-scales
2025-11-20. Updated all the footprints and symbols to their proper layouts. no more fkn errors. Hallefuckinglujah. Fucked up with LM74610 not using the right footprint. minor fix. 2025-11-16.
131 parts - 6 layers152.4 × 92 mm
- 2 layers129.4 × 77 mm
Progetto Lidar
AlessioPasin/Progetto-di-tesi-LiDAR
Questo progetto di tesi è stato realizzato da Pasin Alessio.
44 parts - 4 layers130 × 100 mm
- 2 layers89 × 45 mm
MonitoringSystem PCB
Danielbaker31/HouseholdWaterMonitoringSystem
This is a personal side project created by Daniel, Advait, and Jack. It is a household water monitoring system, allowing households to track how much water they are using, and pinpoint from which source it is coming…
96 parts - 4 layers56.6 × 57.7 mm
MelexisToFcamera4layer
lnsru/melexisToFcamera4layer
Time of Flight camera using MLX75023 and MLX75123, 4 layers pcb done with KiCad
106 parts2MIT - 4 layers70 × 70 mm
IMU V100
embeddedalpha/IMU_V100
Inertial Measurement Unit based around STM32F407VGT6. This is a product development repo.
40 parts1