
TDC7200PW
Texas InstrumentsExtended
-40℃~+85℃ 0.5uA 20MHz 2V~3.6V SPI TSSOP-14 ADCs/DACs - Special Purpose ROHS
- Part id
- ti/TDC7200PW
- Category
- ADCs, DACs, Special Purpose
- Package
- TSSOP-14
- Pins
- 14
- In stock
- 12,208 at JLCPCB (C2653139)
- Used on
- 8 open-source boards
Overview
The TDC7200PW is an ADCs, DACs, Special Purpose made by Texas Instruments in a TSSOP-14 package with 14 pins. -40℃~+85℃ 0.5uA 20MHz 2V~3.6V SPI TSSOP-14 ADCs/DACs - Special Purpose ROHS.
PCBKit's library has its KiCad symbol (Analog & Interface:TDC7200PW, from CERN's library) and its footprint (Package_SO:TSSOP-14_4.4x5mm_P0.65mm, from KiCad's library), ready for a KiCad board. 12,208 are in stock at JLCPCB (part C2653139). 8 open-source boards in 5 repositories on GitHub use it.
Symbol
Footprint
From the datasheet
12- Supply, least
- 2 V · VDD, recommended operating min · p. 5
- Supply, most
- 3.6 V · VDD, recommended operating max · p. 5
- Supply, absolute maximum
- 3.9 V · VDD, absolute max · p. 5
- Works from
- -40 °C · Ambient temperature, recommended min · p. 6
- Works up to
- 85 °C · Ambient temperature, recommended max · p. 6
- Junction, hottest
- 85 °C · Junction temperature, recommended max · p. 6
- Takes working
- 1.35 mA · VDD, typical, EN = HIGH; TDC running · p. 7
- Takes asleep
- 300 nA · VDD, typical shutdown, EN = LOW · p. 7
- A pin gives at most
- 5 mA · Input current at any pin, absolute max magnitude · p. 5
- Junction to air (PW [TSSOP])
- 134.9 K/W · Junction-to-ambient thermal resistance · p. 6
- Junction to board (PW [TSSOP])
- 76.8 K/W · Junction-to-board thermal resistance · p. 6
- Junction to case (PW [TSSOP])
- 63 K/W · Junction-to-case (top) thermal resistance · p. 6
What it is and has
8- Resolution
- 55 ps · p. 1
- Standard Deviation
- 35 ps · p. 1
- Measurement range, Mode 1
- 12 ns to 500 ns · p. 1
- Measurement range, Mode 2
- 250 ns to 8 ms · p. 1
- STOP signals
- Up to 5 · p. 1
- Host interface
- SPI for configuration and register access · p. 1
- Package
- TSSOP (14), 5.00 mm × 4.40 mm · p. 1
- Standard deviation
- 35 ps · p. 1
Around it
3- cap 0.4 µF–2.7 µF (1 µF typical)
- between VREG and GND; Mandatory external LDO decoupling capacitor; ceramic, ESR 100 mΩ maximum. · p. 12
- cap 100 nF
- between VDD and GND; Ceramic bypass capacitor, as close as possible to the VDD pins. · p. 41
- cap greater than 1 µF
- between VDD and GND; Electrolytic or tantalum bulk capacitor; may be near the voltage source terminals or regulator output. · p. 41
Specifications
55| Parameter | Conditions | As printed | Page |
|---|---|---|---|
| Supply voltage VDD | TA = 25°C, VDD = 3.3V, GND = 0V | min -0.3 · max 3.9 V | 5 |
| Terminal input voltage VI | TA = 25°C, VDD = 3.3V, GND = 0V; maximum VDD+0.3 V | min -0.3 V | 5 |
| |Voltage differential| between any two input terminals VDIFF_IN | TA = 25°C, VDD = 3.3V, GND = 0V | max 3.9 V | 5 |
| |Voltage differential| between any input terminal and GND or VDD VIN_GND_VDD | TA = 25°C, VDD = 3.3V, GND = 0V | max 3.9 V | 5 |
| Input current at any pin II | TA = 25°C, VDD = 3.3V, GND = 0V | min -5 · max 5 mA | 5 |
| Ambient temperature TA | min -40 · max 125 °C | 5 | |
| Storage temperature Tstg | min -65 · max 150 °C | 5 | |
| Electrostatic discharge V(ESD) | Human-body model (HBM), per ANSI/ESDA/JEDEC JS-001; rating ±1000 V | min -1000 · max 1000 V | 5 |
| Electrostatic discharge V(ESD) | Charged-device model (CDM), per JEDEC specification JESD22-C101; rating ±250 V | min -250 · max 250 V | 5 |
| Supply voltage VDD | TA = 25°C, GND = 0V | min 2 · max 3.6 V | 5 |
| Terminal voltage VI | TA = 25°C, VDD = 3.3V, GND = 0V; maximum VDD | min 0 V | 5 |
| Voltage input high VIH | TA = 25°C, VDD = 3.3V, GND = 0V; minimum 0.7 × VDD | max 3.6 V | 5 |
| Voltage input low VIL | TA = 25°C, VDD = 3.3V, GND = 0V; maximum 0.3 × VDD | min 0 V | 5 |
| Frequency (Reference/Calibration Clock) FCALIB_CLK | TA = 25°C, VDD = 3.3V, GND = 0V; nominal 8 MHz | min 1 · max 16 MHz | 5 |
| Input clock duty cycle DUTYCLOCK | Nominal | typ 50 % | 5 |
| Minimum Time between Start and Stop Signal T1STARTSTOP_Min | Measurement Mode 1; specified by design | min 12 ns | 5 |
| Minimum Time between 2 Stop Signals T1STOPSTOP_Min | Measurement Mode 1; specified by design | min 67 ns | 5 |
| Maximum time bet. Start and Stop Signal T1STARTSTOP_Max | Measurement Mode 1; specified by design | max 500 ns | 5 |
| Maximum time bet. Start and last Stop Signal T1STOPSTOP_Max | Measurement Mode 1; specified by design | max 500 ns | 5 |
| Maximum rise, fall time for START, STOP signals (20%-80%) TRST, TFST | TA = 25°C, VDD = 3.3V, GND = 0V; value in NOM column | typ 1 ns | 6 |
| Maximum rise, fall time for external CLOCK (20%-80%) TRXCLK, TFXCLK | TA = 25°C, VDD = 3.3V, GND = 0V; value in NOM column | typ 1 ns | 6 |
| Time from TRIG to START TTRIGSTART | TA = 25°C, VDD = 3.3V, GND = 0V; value in NOM column | typ 5 ns | 6 |
| Ambient temperature TA | min -40 · max 85 °C | 6 | |
| Junction temperature TJ | min -40 · max 85 °C | 6 | |
| Junction-to-ambient thermal resistance RθJA | PW [TSSOP], 14 PINS | typ 134.9 °C/W | 6 |
| Junction-to-case (top) thermal resistance RθJC(top) | PW [TSSOP], 14 PINS | typ 63 °C/W | 6 |
| Junction-to-board thermal resistance RθJB | PW [TSSOP], 14 PINS | typ 76.8 °C/W | 6 |
| Junction-to-top characterization parameter ψJT | PW [TSSOP], 14 PINS | typ 12.4 °C/W | 6 |
| Junction-to-board characterization parameter ψJB | PW [TSSOP], 14 PINS | typ 76.2 °C/W | 6 |
| Package thermal impedance θJA | PW [TSSOP], 14 PINS | typ 113 °C/W | 6 |
| Resolution LSB | Single shot measurement; TA = 25°C, VDD = 3.3 V, GND = 0 V | typ 55 ps | 7 |
| Accuracy (Mode 2) TACC-2 | CLOCK = 8 MHz; TA = 25°C, VDD = 3.3 V, GND = 0 V | typ 28 ps | 7 |
| Standard Deviation (Mode 2) TSTD-2 | Measured time = 100 us; TA = 25°C, VDD = 3.3 V, GND = 0 V | typ 50 ps | 7 |
| Standard Deviation (Mode 2) TSTD-2 | Measured time = 1 us; TA = 25°C, VDD = 3.3 V, GND = 0 V | typ 35 ps | 7 |
| Output voltage high VOH | TRIGG, INTB, DOUT; Isource = -2 mA; TA = 25°C, VDD = 3.3 V, GND = 0 V | min 2.31 · typ 2.95 V | 7 |
| Output voltage low VOL | TRIGG, INTB, DOUT; Isink = 2 mA; TA = 25°C, VDD = 3.3 V, GND = 0 V | typ 0.35 · max 0.99 V | 7 |
| Input capacitance Cin | ENABLE, START, STOP, CLOCK, DIN, CSB, SCLK; specified by design | typ 3 pF | 7 |
| Shutdown current Ish | EN = LOW; TA = 25°C, VDD = 3.3 V, GND = 0 V | typ 0.3 · max 2 uA | 7 |
| Quiescent Current A IQA | EN = HIGH; TDC running; TA = 25°C, VDD = 3.3 V, GND = 0 V | typ 1.35 mA | 7 |
| Quiescent Current B IQB | EN = HIGH; TDC OFF, Clock Counter running; TA = 25°C, VDD = 3.3 V, GND = 0 V | typ 71 uA | 7 |
| Quiescent Current C IQC | EN = HIGH; measurement stopped, SPI communication only; TA = 25°C, VDD = 3.3 V, GND = 0 V | typ 87 uA | 7 |
| Quiescent Current D IQD | EN = HIGH, TDC OFF, counter stopped, no communication; TA = 25°C, VDD = 3.3 V, GND = 0 V | typ 50 uA | 7 |
| Pulse width for Start Signal PWSTART | min 10 ns | 7 | |
| Pulse width for Stop Signal PWSTOP | min 10 ns | 7 | |
| SCLK Frequency fSCLK | Serial interface; VDD = 3.3 V | max 20 MHz | 7 |
| SCLK period t1 | VDD = 3.3 V, fSCLK = 20 MHz | min 50 ns | 7 |
| SCLK High Time t2 | VDD = 3.3 V, fSCLK = 20 MHz | min 16 ns | 7 |
| SCLK Low Time t3 | VDD = 3.3 V, fSCLK = 20 MHz | min 16 ns | 7 |
| DIN setup time t4 | VDD = 3.3 V, fSCLK = 20 MHz | min 4 ns | 7 |
| DIN hold time t5 | VDD = 3.3 V, fSCLK = 20 MHz | min 4 ns | 7 |
| CSB fall to SCLK rise t6 | VDD = 3.3 V, fSCLK = 20 MHz | min 6 ns | 7 |
| Last SCLK rising edge to CSB rising edge t7 | VDD = 3.3 V, fSCLK = 20 MHz | min 6 ns | 7 |
| Minimum pause time (CSB high) t8 | VDD = 3.3 V, fSCLK = 20 MHz | min 40 ns | 7 |
| Clk fall to DOUT bus transition t9 | VDD = 3.3 V, fSCLK = 20 MHz | max 12 ns | 7 |
| Time to be ready for Measurement TWAKEUP_PERIOD | LSB within 0.3% of settled value; TA = 25°C, VDD = 3.3 V, GND = 0 V | typ 300 us | 7 |
Pins, by the datasheet
14- 1 ENABLE
- Enable signal to TDC. · p. 4
- 2 TRIGG
- Trigger output signal. · p. 4
- 3 START
- START signal to TDC. · p. 4
- 4 STOP
- STOP signal to TDC. · p. 4
- 5 CLOCK
- Clock Input to TDC. · p. 4
- 6 N.C.
- Not Connected. · p. 4
- 7 GND
- Ground. · p. 4
- 8 INTB
- Interrupt to MCU, active low (open drain). · p. 4
- 9 DOUT
- SPI Data Output. · p. 4
- 10 DIN
- SPI Data Input. · p. 4
- 11 CSB
- SPI Chip Select, active low. · p. 4
- 12 SCLK
- SPI clock. · p. 4
- 13 VREG
- LDO Output terminal for external decoupling cap. · p. 4
- 14 VDD
- Supply input. · p. 4
Ordering codes, by the datasheet
6- TDC7200PW
- TSSOP (PW) | 14 · 90 | TUBE; operating temperature -40 to 85 °C · p. 44
- TDC7200PW.A
- TSSOP (PW) | 14 · 90 | TUBE; operating temperature -40 to 85 °C · p. 44
- TDC7200PWR
- TSSOP (PW) | 14 · 2000 | LARGE T&R; operating temperature -40 to 85 °C · p. 44
- TDC7200PWR.A
- TSSOP (PW) | 14 · 2000 | LARGE T&R; operating temperature -40 to 85 °C · p. 44
- TDC7200PWRG4
- TSSOP (PW) | 14 · 2000 | LARGE T&R; operating temperature -40 to 85 °C · p. 44
- TDC7200PWRG4.A
- TSSOP (PW) | 14 · 2000 | LARGE T&R; operating temperature -40 to 85 °C · p. 44
Open-source boards using it
8- 6 layers152.4 × 92 mm

- 2 layers129.4 × 77 mm

Progetto Lidar
AlessioPasin/Progetto-di-tesi-LiDAR
Questo progetto di tesi è stato realizzato da Pasin Alessio.
44 parts - 4 layers130 × 100 mm

- 2 layers89 × 45 mm

MonitoringSystem PCB
Danielbaker31/HouseholdWaterMonitoringSystem
This is a personal side project created by Daniel, Advait, and Jack. It is a household water monitoring system, allowing households to track how much water they are using, and pinpoint from which source it is coming…
96 parts - 4 layers84.3 × 50.8 mm

PrecisionTimer RevG-1
SepticElectronics/High-Speed-Timer
High Speed Precision Timer 55ps/4ns
128 partsGPL-3.0 - 4 layers84.3 × 50.8 mm

PrecisionTimer RevF
SepticElectronics/High-Speed-Timer
High Speed Precision Timer 55ps/4ns
115 partsGPL-3.0 - 4 layers84.3 × 50.8 mm

PrecisionTimer RevF back
SepticElectronics/High-Speed-Timer
High Speed Precision Timer 55ps/4ns
111 partsGPL-3.0 - 4 layers84.3 × 50.8 mm

PrecisionTimer RevG
SepticElectronics/High-Speed-Timer
High Speed Precision Timer 55ps/4ns
125 partsGPL-3.0
Parts like it
8PCM1808PW
TSSOP-14-40℃~+85℃ 1uA、150uA 2 24 4.5V~5.5V 49.152MHz 96000Hz Audio Analog-to-Digital Converter I2S TSSOP-14 ADCs/DACs - Special Purpose ROHSTexas InstrumentsADCs/DACs - Special PurposeMAX31856MUD+T
TSSOP-14-40℃~+125℃ 10uA 19 3V~3.6V Programmable gain、Digital filtering、Built-in temperature sensor SPI Thermocouple-to-Digital Converter TSSOP-14 ADCs/DACs - Special Purpose ROHSMaxim Integrated (Analog Devices)ADCs/DACs - Special PurposeMAX31856MUD+
TSSOP-14-55℃~+125℃ 1 10uA 19 3V~3.6V Programmable gain、Digital filtering、Built-in temperature sensor SPI Thermocouple-to-Digital Converter TSSOP-14 ADCs/DACs - Special Purpose ROHSMaxim Integrated (Analog Devices)ADCs/DACs - Special PurposePCM1808QPWRQ1
TSSOP-14-40℃~+125℃ 1uA、150uA 2 2.7V~3.6V、4.5V~5.5V 24 96000Hz Audio Analog-to-Digital Converter Built-in TSSOP-14 ADCs/DACs - Special Purpose ROHSTexas InstrumentsADCs/DACs - Special PurposePCM1807PW
TSSOP-14-40℃~+85℃ 1uA 2 2.5V 2.7V~3.6V、4.5V~5.5V 24 96000Hz Audio Analog-to-Digital Converter SPI TSSOP-14 ADCs/DACs - Special Purpose ROHSTexas InstrumentsADCs/DACs - Special PurposePCM1808PWG4
TSSOP-144.5V~5.5V I2S TSSOP-14 ADCs/DACs - Special Purpose ROHSTexas InstrumentsADCs/DACs - Special PurposeZSSC3122AA1B
TSSOP-14-20℃~+125℃ 1.8V~5.5V Capacitive Transducer Programmable gain、Power-down mode、Built-in temperature sensor SPI、I2C TSSOP-14 ADCs/DACs - Special Purpose ROHSRenesas ElectronicsADCs/DACs - Special PurposeZSSC3122AA1C
TSSOP-141.8V~5.5V SPI、I2C TSSOP-14 ADCs/DACs - Special Purpose ROHSRenesas ElectronicsADCs/DACs - Special Purpose
Questions
Is there a KiCad symbol and footprint for the TDC7200PW?
Yes. The symbol is Analog & Interface:TDC7200PW and the footprint Package_SO:TSSOP-14_4.4x5mm_P0.65mm, both drawn on this page. PCBKit places them on a board for you when you design with it.
What package is the TDC7200PW?
TSSOP-14, with 14 pins. Its footprint is drawn on this page.
Where is the TDC7200PW datasheet?
Texas Instruments publishes it: the Datasheet link on this page opens it.
Where can I order the TDC7200PW?
JLCPCB lists it as part C2653139, with 12,208 in stock; the sellers' links on this page open their listings.
What can replace the TDC7200PW?
Parts like it in the library: the PCM1808PW by Texas Instruments, the MAX31856MUD+T by Maxim Integrated (Analog Devices), the MAX31856MUD+ by Maxim Integrated (Analog Devices) and the PCM1808QPWRQ1 by Texas Instruments. Check their datasheets: a part that fits the footprint may still differ in its ratings.
Which open-source boards use the TDC7200PW?
8 boards in 5 repositories on GitHub; the most starred are listed on this page, with their KiCad files.