

STM32 Smart Environmental Sensing Hub
This project implements the board recorded in the engineering portfolio: STM32WB55 MCU, USB-C power/data, single-cell LiPo charging, 3.3 V regulation, I2C environmental sensing, external SPI flash and BLE/RF access.
- Size
- 80 × 50 mm
- Copper layers
- 4
- Thickness
- 1.6 mm
- Parts
- 37
- Nets
- 28
- Pads
- 155
- Tracks, vias
- 22, 0
- Pours
- 2
- Routed
- Yes
- KiCad
- KiCad 8 (file 20240108)
- Created
- 2 Oct 2026
- Updated
- 2 Oct 2026
Overview
STM32 Smart Environmental Sensing Hub is an open-source printed circuit board by saihibbkaura, from the saihibbkaura/saihibb-kaura.github.io repository on GitHub. It is a 4-layer board of 80 × 50 mm with 37 parts on 28 nets, routed with 22 tracks and 0 vias.
It is built around the STM32WB55CGU6, MLPF-WB55-01E3 and BME280, with the W25Q128JVSIQ, AP2112K-3.3 and MCP73831-2ACI/OT among its other parts. Its parts include 12 capacitors, 6 resistors, 6 ICs, 4 connectors and 2 inductors. It belongs with the STM32 boards of this library.
Main components
8STM32WB55CGU6
UFQFPN-48(7x7)UFQFPN-48(7x7) Microcontrollers (MCU/MPU/SOC) ROHSSTMicroelectronicsRF Transceiver ICsMLPF-WB55-01E3
SMD-6P,1.6x1mm-40℃~+105℃ 1.1dB 2.4GHz~2.5GHz 50Ω Low Pass SMD-6P,1.6x1mm RF Filters ROHSSTMicroelectronicsRF FiltersBME280
LGA-8(2.5x2.5)-40℃~+85℃ 0%RH~100%RH 1.71V~3.6V 1.8uA 16bit I2C、SPI ±0.5℃ ±3%RH LGA-8(2.5x2.5) Temperature and Humidity Sensor ROHSBoschTemperature And Humidity SensorW25Q128JVSIQ
SOIC-8-208mil-40℃~+85℃ 100,000 cycles 120ms@(32KB) 128Mbit 133MHz 1uA 2.7V~3.6V 20 Years 3ms Power-on reset、Hardware write protection、Software write protection、Write enable latch、Absolute write protection SPI SOIC-8-208mil NOR FLASH ROHSWinbondNOR FLASHAP2112K-3.3
SOT253.3V 600mA CMOS Low Dropout Linear Regulator with EnableDiodes IncorporatedUncategorisedMCP73831-2ACI/OT
SOT-23-5-40℃~+85℃ 1 3.75V~6V 4.2V 53uA 550mA Charging IC Lithium Battery Not supported SOT-23-5 Battery Management ROHSMicrochip TechnologyBattery ManagementUSBLC6-2SC6
SOT-23-60.35pF、0.8pF 100nA 150W@8/20us 15V 2 5V 6A@8/20us 6V ESD SOT-23-6 ESD and Surge Protection (TVS/ESD) ROHSUMWESD And Surge Protection (TVS/ESD)U.FL-R-SMT-1
Up to 6GHz Ultra Small Surface Mount Male Coaxial Connectors U.FL SeriesHirose ElectricUncategorised
README
evidence/p11-stm32/STM32_Sensing_Hub_KiCad/README.mdSTM32 Smart Environmental Sensing Hub — KiCad reference design
This project implements the board recorded in the engineering portfolio: STM32WB55 MCU, USB-C power/data, single-cell LiPo charging, 3.3 V regulation, I2C environmental sensing, external SPI flash and BLE/RF access.
Important design status
- Board size is set to 80 mm x 50 mm as a mechanical baseline because the earlier resume record preserved the architecture but not a locked mechanical dimension. Change the Edge.Cuts rectangle if a different enclosure is required.
- The PCB is a 4-layer Signal / Ground / Power / Signal stackup, matching the portfolio description.
- RF, crystal, power and USB routing are arranged as a reference implementation. Before fabrication, import the exact fabricator stackup and run KiCad ERC/DRC. RF impedance must be recalculated from the manufacturer's actual dielectric thickness and Dk.
- The included board file is intentionally self-contained for the main footprints used in the layout.
Layer stack
L1: Top signal + components L2: Solid GND plane L3: 3V3 / VBAT / USB_5V power distribution L4: Bottom signal Nominal finished thickness: 1.60 mm Copper: 1 oz outer, 1 oz inner nominal
Main interfaces
- USB-C: VBUS, D+, D-, CC1, CC2
- Battery: 1S LiPo, MCP73831 charger
- MCU: STM32WB55CGU6, UFQFPN48
- I2C1: PB8 = SCL, PB9 = SDA
- SPI1: PA5 = SCK, PA6 = MISO, PA7 = MOSI, PA4 = CS
- SWD: PA13 = SWDIO, PA14 = SWCLK, NRST
- USB FS: PA11 = USB_DM, PA12 = USB_DP
- RF: STM32WB55 RF1 -> 50-ohm RF front end -> U.FL
Verification checklist
- ERC with all power-input pins correctly driven.
- DRC using manufacturer minimum trace/space and via rules.
- Confirm STM32WB55 AN5165 RF layout and SMPS rules.
- Confirm crystal placement and load settings against the selected crystals.
- Confirm MCP73831 charge-current resistor and battery protection strategy.
- Confirm USB-C CC resistors and ESD protection.
- Confirm 50-ohm RF width from the final stackup.
- Inspect all QFN/LGA pads and solder-mask openings.
- Generate Gerbers, drill files, BOM and CPL only after final DRC.
Parts
37| Qty | Value | Footprint | References |
|---|---|---|---|
| 1 | 100nF | Portfolio:C7 | C7 |
| 1 | 100nF | Portfolio:C8 | C8 |
| 1 | 100nF | Portfolio:C3 | C3 |
| 1 | 100nF | Portfolio:C1 | C1 |
| 1 | 100nF | Portfolio:C10 | C10 |
| 1 | 100nF | Portfolio:C2 | C2 |
| 1 | 10k | Portfolio:R5 | R5 |
| 1 | 10k | Portfolio:R6 | R6 |
| 1 | 10nH | Portfolio:L2 | L2 |
| 1 | 1uF | Portfolio:C4 | C4 |
| 1 | 2.2uH | Portfolio:L1 | L1 |
| 1 | 32.768kHz | Portfolio:Y2 | Y2 |
| 1 | 32MHz | Portfolio:Y1 | Y1 |
| 1 | 4.7k | Portfolio:R4 | R4 |
| 1 | 4.7k | Portfolio:R3 | R3 |
| 1 | 4.7uF | Portfolio:C6 | C6 |
| 1 | 4.7uF | Portfolio:C5 | C5 |
| 1 | 4.7uF | Portfolio:C11 | C11 |
| 1 | 4.7uF | Portfolio:C12 | C12 |
| 1 | 4.7uF | Portfolio:C9 | C9 |
| 1 | 5.1k | Portfolio:R1 | R1 |
| 1 | 5.1k | Portfolio:R2 | R2 |
| 1 | AP2112K-3.3 | Portfolio:U3 | U3 |
| 1 | BME280 | Portfolio:U4 | U4 |
| 1 | JST-PH-2 | Portfolio:J2 | J2 |
| 1 | M3 Mount | Portfolio:H3 | H3 |
| 1 | M3 Mount | Portfolio:H2 | H2 |
| 1 | M3 Mount | Portfolio:H1 | H1 |
| 1 | M3 Mount | Portfolio:H4 | H4 |
| 1 | MCP73831-2ACI/OT | Portfolio:U2 | U2 |
| 1 | MLPF-WB55-01E3 | Portfolio:FLT1 | FLT1 |
| 1 | STM32WB55CGU6 | Portfolio:U1 | U1 |
| 1 | SWD 1x6 | Portfolio:J3 | J3 |
| 1 | U.FL-R-SMT-1 | Portfolio:J4 | J4 |
| 1 | USB-C 16P | Portfolio:J1 | J1 |
| 1 | USBLC6-2SC6 | Portfolio:U6 | U6 |
| 1 | W25Q128JVSI | Portfolio:U5 | U5 |
Similar boards
- 4 layers40.8 × 40.8 mm

- 4 layers52.5 × 22.9 mm

Feather STM32WB55
makeristic/Feather_STM32WB55
KiCad STM32WB55 Bluetooth development board in the Adafruit Feather form factor, with USB-C and STEMMA QT. Work in progress.
50 parts2MIT - 4 layers160 × 130 mm

Device
jayis1/hardware-design-lab
Full-cycle hardware device designs — each device in its own subfolder with architecture, schematics, PCB layout, and software stack
8 parts - 6 layers133.1 × 133.1 mm

AERIS H743-PCB
7903555032/AERIS-H743-PCB
A 6-layer STM32H743-based embedded development and flight-control/data-logging PCB designed as a practical hardware-design and PCB-layout project.
114 parts1 - 4 layers25.4 × 25.4 mm

Zeo1.2 devboard
zeodotdev/zeo-boards
ESP32-S3 development board with onboard BME280 (temperature, humidity, pressure) and LSM6DS3 (6-axis IMU) sensors. This repo contains the designs, ESP-IDF firmware, and a Python plotter for visualization.
92 parts3 - 4 layers70 × 99.9 mm

Micromouse
UBIEEE/FrankenMouse
FrankenMouse is a MicroMouse robot that was designed, built, and programmed from scratch by members of the University at Buffalo's IEEE Student Branch.
100 parts6MIT - 4 layers58 × 38 mm

- 4 layers117 × 77 mm

ProdDeck
arsovskiteodor/A.ProdDeck
Open-hardware macro pad (WIP): custom KiCad PCB with keys, encoders and a fader, plus firmware and a desktop configurator
69 parts
Questions
How big is the STM32 Smart Environmental Sensing Hub PCB?
It measures 80 × 50 mm and has 4 copper layers, 1.6 mm thick.
What parts does the STM32 Smart Environmental Sensing Hub use?
37 parts, built around the STM32WB55CGU6, MLPF-WB55-01E3, BME280 and W25Q128JVSIQ. The full list of its parts is on this page, with links to each part's symbol and footprint where PCBKit's library has them.
Where can I download the STM32 Smart Environmental Sensing Hub KiCad files?
From the saihibbkaura/saihibb-kaura.github.io repository on GitHub, at the commit this page was made from: the board is evidence/p11-stm32/STM32_Sensing_Hub_KiCad/STM32_Smart_Environmental_Sensing_Hub.kicad_pcb. PCBKit opens the board in the browser, with nothing to install.
Can I use the STM32 Smart Environmental Sensing Hub design in my own project?
Its repository states no licence, so its author keeps all rights: ask saihibbkaura before reusing the design.