Skip to the content
12345

MCP73831-2ACI/OT

Microchip TechnologyExtended

-40℃~+85℃ 1 3.75V~6V 4.2V 53uA 550mA Charging IC Lithium Battery Not supported SOT-23-5 Battery Management ROHS

Part id
microchip/MCP73831-2ACI/OT
Category
Battery Management
Package
SOT-23-5
Pins
5
In stock
6,086 at JLCPCB (C424093)
Used on
9 open-source boards

Overview

The MCP73831-2ACI/OT is a battery Management made by Microchip Technology in a SOT-23-5 package with 5 pins. -40℃~+85℃ 1 3.75V~6V 4.2V 53uA 550mA Charging IC Lithium Battery Not supported SOT-23-5 Battery Management ROHS.

PCBKit's library has its KiCad symbol (dk_PMIC-Battery-Chargers:MCP73831T-2ACI_OT, from Digikey) and its footprint (Package_TO_SOT_SMD:SOT-23-5, from KiCad's library), ready for a KiCad board. 6,086 are in stock at JLCPCB (part C424093). 9 open-source boards in 9 repositories on GitHub use it.

Symbol

1STAT2VSS3VBAT4VDD5PROG
dk_PMIC-Battery-Chargers:MCP73831T-2ACI_OTFrom Digikey

Footprint

12345
Package_TO_SOT_SMD:SOT-23-5From KiCad's library

From the datasheet

16
Supply, least
3.75 V · VDD, minimum supply voltage · p. 3
Supply, most
6 V · VDD, maximum supply voltage · p. 3
Supply, absolute maximum
7 V · VDD, absolute maximum · p. 3
Works from
-40 °C · TA, minimum specified ambient temperature · p. 5
Works up to
85 °C · TA, maximum specified ambient temperature · p. 5
Junction, hottest
125 °C · TJ, maximum operating junction temperature · p. 5
Takes working
510 µA · VDD, typical supply current while charging · p. 3
Takes at most
1.5 mA · VDD, maximum supply current while charging · p. 3
Takes asleep
25 µA · VDD, typical disabled current with PROG floating · p. 3
Takes asleep
1 µA · VDD, typical power-down current with VDD < VBAT - 50 mV · p. 3
Takes asleep
100 nA · VDD, typical current below UVLO stop threshold · p. 3
Gives
500 mA · maximum programmable charge current · p. 1
Output
4.2 V · VBAT, typical regulated output for MCP7383X-2 · p. 3
A pin gives at most
25 mA · STAT, maximum sink current · p. 4
A pin gives at most
35 mA · STAT, maximum source current · p. 4
Junction to air (5-Lead, SOT-23)
230 K/W · typical, 4-layer JC51-7 standard board, natural convection · p. 5

What it is and has

9
Charge management
Linear · p. 1
Pass transistor
Integrated · p. 1
Current sense
Integrated · p. 1
Protection
Reverse discharge protection · p. 1
Programmable charge current
15 mA to 500 mA · p. 1
Charge status output
Tri-state · p. 1
Automatic power-down
Supported · p. 1
Thermal regulation
Supported · p. 1
Package
5-Lead, SOT-23 · p. 1

Around it

3
cap minimum of 4.7 µF
between VDD and VSS; Input supply bypass capacitor. · p. 11
cap minimum of 4.7 µF
between VBAT and VSS; Ensures loop stability when the battery is disconnected. · p. 11
cap 4.7 µF
between VBAT and VSS; Recommended minimum bypass capacitance for stability in Constant-Voltage mode, including operation without a battery load. · p. 18

Specifications

50
ParameterConditionsAs printedPage
VDD VDDmax 7 V3
All Inputs and Outputs w.r.t. VSSMaximum: (VDD+0.3)Vmin -0.3 V3
Storage temperaturemin -65 · max 150 °C3
Human Body ModelESD protection on all pins; 1.5 kΩ in series with 100 pFmin 4 kV3
Machine ModelESD protection on all pins; 200 pF, No Series Resistancemax 400 V3
Supply Voltage VDDmin 3.75 · max 6 V3
Supply Current ISSChargingtyp 510 · max 1500 uA3
Supply Current ISSCharge Complete, No Batterytyp 53 · max 200 uA3
Supply Current ISSPROG Floatingtyp 25 · max 50 uA3
Supply Current ISSVDD < (VBAT - 50 mV)typ 1 · max 5 uA3
Supply Current ISSVDD < VSTOPtyp 0.1 · max 2 uA3
UVLO Start Threshold VSTARTVDD Low-to-Highmin 3.3 · typ 3.45 · max 3.6 V3
UVLO Stop Threshold VSTOPVDD High-to-Lowmin 3.2 · typ 3.38 · max 3.5 V3
UVLO Hysteresis VHYStyp 70 mV3
Regulated Output Voltage VREGMCP7383X-2; VDD = [VREG(typical)+1V]; IOUT = 10 mA; TA = -5°C to +55°Cmin 4.168 · typ 4.2 · max 4.232 V3
Line Regulation VBAT/VBAT)/VDD|VDD = [VREG(typical)+1V] to 6V, IOUT = 10 mAtyp 0.09 · max 0.3 %/V3
Load Regulation VBAT/VBAT|IOUT = 10 mA to 50 mA; VDD = [VREG(typical)+1V]typ 0.05 · max 0.3 %3
Supply Ripple Attenuation PSRRIOUT=10 mA, 10Hz to 1 kHztyp 52 dB3
Supply Ripple Attenuation PSRRIOUT=10 mA, 10Hz to 10 kHztyp 47 dB3
Supply Ripple Attenuation PSRRIOUT=10 mA, 10Hz to 1 MHztyp 22 dB3
Fast Charge Current Regulation IREGPROG = 10 kΩmin 90 · typ 100 · max 110 mA3
Fast Charge Current Regulation IREGPROG = 2.0 kΩ; Not production tested. Ensured by design.min 450 · typ 505 · max 550 mA3
Fast Charge Current Regulation IREGPROG = 67 kΩ; TA = -5°C to +55°Cmin 12.5 · typ 14.5 · max 16.5 mA3
Precondition Hysteresis VPHYSVBAT High-to-Lowtyp 110 mV4
ON-Resistance RDSONVDD = 3.75V, TJ = 105°Ctyp 350 m4
Battery Detection Current IBAT_DETVBAT Source Currenttyp 6 uA4
No-Battery-Present Impedance ZNO_BATVBAT Impedance ≥ ZNO_BAT for No Battery condition; Not production tested. Ensured by design.min 2 M4
Output Reverse Leakage Current IDISCHARGEPROG Floatingtyp 0.15 · max 2 uA4
Output Reverse Leakage Current IDISCHARGEVDD Floatingtyp 0.25 · max 2 uA4
Output Reverse Leakage Current IDISCHARGEVDD < VSTOPtyp 0.15 · max 2 uA4
Output Reverse Leakage Current IDISCHARGECharge Completetyp -5.5 · max -15 uA4
Sink Current ISINKSTATmax 25 mA4
Low Output Voltage VOLISINK = 4 mAtyp 0.4 · max 1 V4
Source Current ISOURCESTATmax 35 mA4
Input Leakage Current ILKHigh-Impedancetyp 0.03 · max 1 uA4
Charge Impedance Range RPROGPROG Inputmin 2 · max 67 k4
Minimum Shutdown Impedance RPROGPROG Inputmin 70 · max 200 k4
Die Temperature TSDThermal Shutdowntyp 150 C5
Die Temperature Hysteresis TSDHYSThermal Shutdowntyp 10 C5
UVLO Start Delay tSTARTVDD Low-to-Highmax 5 ms5
Transition Time Out of Preconditioning tDELAYVBAT < VPTH to VBAT > VPTHmax 1 ms5
Current Rise Time Out of Preconditioning tRISEIOUT Rising to 90% of IREGmax 1 ms5
Termination Comparator Filter tTERMAverage IOUT Fallingmin 0.4 · typ 1.3 · max 3.2 ms5
Charge Comparator Filter tCHARGEAverage VBATmin 0.4 · typ 1.3 · max 3.2 ms5
Status Output turn-off tOFFISINK = 1 mA to 0 mAmax 200 us5
Status Output turn-on tONISINK = 0 mA to 1 mAmax 200 us5
Specified Temperature Range TAmin -40 · max 85 °C5
Operating Temperature Range TJmin -40 · max 125 °C5
Storage Temperature Range TAmin -65 · max 150 °C5
5-Lead, SOT-23 JA4-Layer JC51-7 Standard Board, Natural Convection (Note 2)typ 230 °C/W5

Pins, by the datasheet

5
1 STAT
Tri-state charge status output for an LED or host microcontroller interface. · p. 11
2 VSS
Battery management 0V reference; connect to the negative terminal of the battery and input supply. · p. 11
3 VBAT
Battery charge control output; connect to the positive battery terminal and bypass to VSS with at least 4.7 uF for stability when the battery is disconnected. · p. 11
4 VDD
Battery management input supply; bypass to VSS with at least 4.7 uF. · p. 11
5 PROG
Current regulation set and charge control enable; connect a resistor to VSS to set charging currents, or float to disable. · p. 11

Open-source boards using it

9See all 9
  • 2 layers43 × 20 mmEdge detector, the printed circuit board in 3D

    Edge detector

    itstoomuchbutter/edge_detector

    50 parts1
  • 2 layers90 × 58 mmCrappyCampCam, the printed circuit board in 3D

    CrappyCampCam

    spacehuhn/CrappyCampCam-PCB

    25 parts1
  • 4 layers40.3 × 68.8 mmNrfMain, the printed circuit board in 3D

    NrfMain

    batkay/CapstonePCB

    76 parts
  • 2 layers49 × 71 mmSonpakharu, the printed circuit board in 3D

    Sonpakharu

    bkrajendra/sonpakharu

    Wireless Data Aggregation System using the ESP-32 S3

    71 parts
  • 2 layers234.5 × 120.8 mmSmk kbd devkit, the printed circuit board in 3D

    Smk kbd devkit

    mburger89/SMK_Keyboard_DevKit

    59-key hot-swap mechanical keyboard PCB carrier for a socketed ESP32-C6-DevKitC-1 dev board — KiCad project generated/routed by Python scripts

    148 parts
  • 4 layers80 × 50 mmSTM32 Smart Environmental Sensing Hub, the printed circuit board in 3D

    STM32 Smart Environmental Sensing Hub

    saihibbkaura/saihibb-kaura.github.io

    This project implements the board recorded in the engineering portfolio: STM32WB55 MCU, USB-C power/data, single-cell LiPo charging, 3.3 V regulation, I2C environmental sensing, external SPI flash and BLE/RF access.

    37 parts
  • 2 layers22.4 × 31.6 mmHackheld Vega LiPo, the printed circuit board in 3D

    Hackheld Vega LiPo

    SpacehuhnTech/HackHeld

    Hackable Handheld

    18 parts277

Parts like it

8

Questions

Is there a KiCad symbol and footprint for the MCP73831-2ACI/OT?

Yes. The symbol is dk_PMIC-Battery-Chargers:MCP73831T-2ACI_OT and the footprint Package_TO_SOT_SMD:SOT-23-5, both drawn on this page. PCBKit places them on a board for you when you design with it.

What package is the MCP73831-2ACI/OT?

SOT-23-5, with 5 pins. Its footprint is drawn on this page.

Where is the MCP73831-2ACI/OT datasheet?

Microchip Technology publishes it: the Datasheet link on this page opens it.

Where can I order the MCP73831-2ACI/OT?

JLCPCB lists it as part C424093, with 6,086 in stock; the sellers' links on this page open their listings.

What can replace the MCP73831-2ACI/OT?

Parts like it in the library: the TP4054 by JSMSEMI, the TP4054-42-SOT25R by TOPPOWER, the MCP73832-2ACI/OT by Microchip Technology and the TP4054 by UMW. Check their datasheets: a part that fits the footprint may still differ in its ratings.

Which open-source boards use the MCP73831-2ACI/OT?

9 boards in 9 repositories on GitHub; the most starred are listed on this page, with their KiCad files.