

Controller
RVL Controller Board schematics and documentation
- Size
- 42.8 × 35.9 mm
- Copper layers
- 4
- Thickness
- 1.6 mm
- Parts
- 28
- Nets
- 47
- Pads
- 148
- Tracks, vias
- 357, 80
- Pours
- 6
- Routed
- Yes
- KiCad
- KiCad 8.0 (file 20240108)
- Created
- 28 Sep 2019
- Updated
- 21 Oct 2026
Overview
Controller is an open-source printed circuit board by rvl-system, from the rvl-system/rvl-boards repository on GitHub. It is a 4-layer board of 42.8 × 35.9 mm with 28 parts on 47 nets, routed with 357 tracks and 80 vias.
It is built around the ESP32-WROOM-32D. Its parts include 7 resistors, 4 ICs, 3 capacitors, 3 switches and 1 diode. It belongs with the ESP32 boards of this library.
Main components
1README
receiver/README.mdRVL receiver Board
Note: This board is still in development, and documentation is currently sparse.
The RVL receiver board is a custom board that runs the RVL Firmware, and is intended for use as both a development board and an LED receiver. This board features:
- ESP32 dual core processor
- Compatible with 3 or 4 pin 5V LED strips supported by FastLED
- Solder jumper for switching between 3 and 4 pin headers (optional)
- Can be powered from USB, or can be "backfed" power from the LED strip connected to it
- 3.3V to 5V level translation on LED control pins
- An LCD and tiny 5-way joystick for controlling the device directly
- A 16-pin header, with GPIO, UART, JTAG, I2C, and ADC pins exposed
- Can be programmed using JTAG + OpenOCD or UART + esptool.py
- JTAG is the recommended way to interact with this device. The experience is a lot smoother, and you can also debug the device with breakpoints/variable inspection.
- RVL Firmware includes a script that is preconfigured to use JTAG+OpenOCD with this device and the FTDI C232HM-DDHSL-0 MSSPE cable
GPIO Header Pins
The GPIO header has the following layout:
| TMS | TCK | GND | 26 | 25 | 18 | 23 | VCC |
| TDI | TDO | RXD | TXD | 27 | 5 | 19 | GND |
Each pin has the following functionality*:
| Pin | Functions |
|---|---|
| TMS | GPIO14, ADC2_CH6, TOUCH6, RTC_GPIO16, MTMS, HSPICLK, HS2_CLK, SD_CLK, EMAC_TXD2 |
| TDI | GPIO12, ADC2_CH5, TOUCH5, RTC_GPIO15, MTDI, HSPIQ, HS2_DATA2, SD_DATA2, EMAC_TXD3 |
| TCK | GPIO13, ADC2_CH4, TOUCH4, RTC_GPIO14, MTCK, HSPID, HS2_DATA3, SD_DATA3, EMAC_RX_ER |
| TDO | GPIO15, ADC2_CH3, TOUCH3, MTDO, HSPICS0, RTC_GPIO13, HS2_CMD, SD_CMD, EMAC_RXD3 |
| GND | Ground (shown as EN in the photo, but has been changed in the most recent revision) |
| RXD | GPIO3, U0RXD, CLK_OUT2 |
| 26 | GPIO26, DAC_2, ADC2_CH9, RTC_GPIO7, EMAC_RXD1 |
| TXD | GPIO1, U0TXD, CLK_OUT3, EMAC_RXD2 |
| 25 | GPIO25, DAC_1, ADC2_CH8, RTC_GPIO6, EMAC_RXD0 |
| 27 | GPIO27, ADC2_CH7, TOUCH7, RTC_GPIO17, EMAC_RX_DV |
| 23 | GPIO23, GPIO23, HS1_STROBE, VSPID/VSPIMOSI |
| 18 | GPIO18, GPIO18, HS1_DATA7, VSPICLK |
| 19 | GPIO19, GPIO19, U0CTS, VSPIQ/VSPMISO, EMAC_TXD0 |
| 5 | GPIO5, GPIO5, HS1_DATA6, VSPICS0, EMAC_RX_CLK |
| VCC | 3.3 volt power (limited to 500mA total including CPU) |
| GND | Ground |
*This data comes from the ESP32 WROOM datasheet.
Photos
Here is the front of the board:

Here is the back of the board:

Here is the board running with a WS2812b LED strip attached

And here is a video of an art piece I designed the lighting for using an older version of this board at Burning Man 2019:
Parts
28| Qty | Value | Footprint | References |
|---|---|---|---|
| 3 | 10k | controller:R0805 | R3, R4, R7 |
| 2 | 68 | controller:R0805 | R1, R2 |
| 2 | MOMENTARY-SWITCH-SPST-2-SMD-4.6X2.8MM | controller:TACTILE_SWITCH_SMD_4.6X2.8MM | S2, S3 |
| 2 | MountingHole | MountingHole:MountingHole_3.5mm | H1, H2 |
| 2 | SN74LVC1T45DBVRDBV6-M | controller:DBV6-M | U3, U4 |
| 1 | 10118194-MICRO-USB | controller:10118194-MICRO-USB | U1 |
| 1 | 10k | controller:2012-4N-CONCAVE | R5 |
| 1 | 10uF | Capacitor_SMD:C_0805_2012Metric_Pad1.18x1.45mm_HandSolder | C2 |
| 1 | 1k | Resistor_SMD:R_0805_2012Metric_Pad1.20x1.40mm_HandSolder | R6 |
| 1 | 1uF | controller:C0805 | C3 |
| 1 | 2.2uH | Inductor_SMD:L_0805_2012Metric_Pad1.05x1.20mm_HandSolder | L1 |
| 1 | 4.7uF | Capacitor_SMD:C_0805_2012Metric_Pad1.18x1.45mm_HandSolder | C1 |
| 1 | CONN_04SCREW | controller:SCREWTERMINAL-3.5MM-4 | J1 |
| 1 | ESP32-WROOM-32D | controller:ESP32-WROOM-32D | U$2 |
| 1 | JOYSTICK_MINI | controller:JOYSTICK_MINI | S1 |
| 1 | LED Type | Jumper:SolderJumper-3_P1.3mm_Bridged2Bar12_RoundedPad1.0x1.5mm_NumberLabels | SJ1 |
| 1 | LM3671MF-3.3/NOPBMF05A-M | controller:MF05A-M | U2 |
| 1 | PINHD-1X4 | controller:1X04 | JP1 |
| 1 | PINHD-2X8 | controller:2X08 | JP2 |
| 1 | Power | LED_SMD:LED_0805_2012Metric_Pad1.15x1.40mm_HandSolder | LED1 |
| 1 | SJ | Jumper:SolderJumper-2_P1.3mm_Bridged_RoundedPad1.0x1.5mm | SJ2 |
| 1 | SSD1306-OLED | controller:SSD1306-OLED | U$5 |
More from rvl-system/rvl-boards
3- 4 layers26.2 × 28 mm

- 4 layers38.1 × 17.6 mm

- 4 layers20.1 × 29.4 mm

Similar boards
- 2 layers72 × 42 mm

NRF24 jammer
W0rthlessS0ul/nRF24_jammer
The nRF24 jammer is a powerful tool that requires an ESP32 and configurable numbers of NRF24 modules to assemble.
51 parts1kMIT - 2 layers100 × 57 mm

- 2 layers189.5 × 204.9 mm

SmartSpin2k Panelized
doudar/SmartSpin2k
Transform your spin bike into a Smart Trainer!
749 parts292GPL-2.0 - 2 layers40 × 53.6 mm

- 2 layers147 × 80 mm

Controller
voltlog/Valve-Actuator
If you are looking for sources of previous revisions (revA, revB, revC) checkout the different branches of this repo.
93 parts108GPL-3.0 - 2 layers33.5 × 20 mm

JURA WiFi Dongle
Jutta-Proto/protocol-cpp
C++ JURA protocol implementation for controlling a Jura coffee maker over a serial (UART) connection.
31 parts86GPL-3.0 - 2 layers99.5 × 90.5 mm

- 2 layers22 × 66.5 mm

Questions
How big is the Controller PCB?
It measures 42.8 × 35.9 mm and has 4 copper layers, 1.6 mm thick.
What parts does the Controller use?
28 parts, built around the ESP32-WROOM-32D. The full list of its parts is on this page, with links to each part's symbol and footprint where PCBKit's library has them.
Where can I download the Controller KiCad files?
From the rvl-system/rvl-boards repository on GitHub, at the commit this page was made from: the board is controller/controller.kicad_pcb and its schematic controller/ESP.kicad_sch. PCBKit opens the board in the browser, with nothing to install.
Can I use the Controller design in my own project?
Its repository states no licence, so its author keeps all rights: ask rvl-system before reusing the design.