
LPC176x MultiFunction
RobertPHeller/RPi-RRCircuits
A collection of circuit designs for various MCUs, not just Raspberry Pis relating to Model Railroading

A collection of circuit designs for various MCUs, not just Raspberry Pis relating to Model Railroading
CANHat is an open-source printed circuit board by RobertPHeller, from the RobertPHeller/RPi-RRCircuits repository on GitHub. It is a 2-layer board of 65 × 56 mm with 29 parts on 27 nets, routed with 203 tracks and 32 vias.
It is built around the MCP2551-I/P, LM78L05ACZ and MCP2515-I, with the RJ45 among its other parts. Its parts include 9 capacitors, 6 connectors, 3 resistors, 3 ICs and 2 diodes. It belongs with the ESP32 boards of this library.
This is a SMD variant of 16DriverOutputHAT.
| Qty | Value | Footprint | References |
|---|---|---|---|
| 4 | RPi_Hat:RPi_Hat_Mounting_Hole | H1, H2, H3, H4 | |
| 3 | .1 uf | C1 | C3, C7, C8 |
| 2 | 22 pf | C2 | C2, C4 |
| 2 | 60 Ohms | R1 | R2, R3 |
| 2 | DIODESCH | D3 | D1, D2 |
| 2 | RJ45 | RJ45_8N-S | J5, J6 |
| 1 | 0.33 uf | C1V7 | C5 |
| 1 | 10 uf | C1V5 | C1 |
| 1 | 10K Ohms | R1 | R1 |
| 1 | 12 Volts | bornier2 | T1 |
| 1 | 15 uf | C1 | C6 |
| 1 | 16 MHz | HC-49V | X1 |
| 1 | 47 nf | C1 | C9 |
| 1 | LM78L05ACZ | TO92 | U3 |
| 1 | MCP2515 | DIP-18__300 | U1 |
| 1 | MCP2551 | DIP-8__300 | U2 |
| 1 | PWR Select | PIN_ARRAY_3X1 | J3 |
| 1 | RPi_GPIO | RPi_Hat:Pin_Header_Straight_2x20 | J0 |
| 1 | SPI Select | PIN_ARRAY_3X1 | J1 |
| 1 | Termination | PIN_ARRAY_2X2 | J4 |

RobertPHeller/RPi-RRCircuits
A collection of circuit designs for various MCUs, not just Raspberry Pis relating to Model Railroading

RobertPHeller/RPi-RRCircuits
A collection of circuit designs for various MCUs, not just Raspberry Pis relating to Model Railroading

RobertPHeller/RPi-RRCircuits
A collection of circuit designs for various MCUs, not just Raspberry Pis relating to Model Railroading

RobertPHeller/RPi-RRCircuits
A collection of circuit designs for various MCUs, not just Raspberry Pis relating to Model Railroading

RobertPHeller/RPi-RRCircuits
A collection of circuit designs for various MCUs, not just Raspberry Pis relating to Model Railroading

RobertPHeller/RPi-RRCircuits
A collection of circuit designs for various MCUs, not just Raspberry Pis relating to Model Railroading

RobertPHeller/RPi-RRCircuits
A collection of circuit designs for various MCUs, not just Raspberry Pis relating to Model Railroading

RobertPHeller/RPi-RRCircuits
A collection of circuit designs for various MCUs, not just Raspberry Pis relating to Model Railroading

RobertPHeller/RPi-RRCircuits
A collection of circuit designs for various MCUs, not just Raspberry Pis relating to Model Railroading

RobertPHeller/RPi-RRCircuits
A collection of circuit designs for various MCUs, not just Raspberry Pis relating to Model Railroading

RobertPHeller/RPi-RRCircuits
A collection of circuit designs for various MCUs, not just Raspberry Pis relating to Model Railroading

RobertPHeller/RPi-RRCircuits
A collection of circuit designs for various MCUs, not just Raspberry Pis relating to Model Railroading


sharst/metaldetector-shield
Hardware and Software for a custom build metaldetector + pressure sensing shield

WATonomous/interfacing-mono
repo for all firmware, ROS nodes, messages, and schematics to live





knoerk/MicroGasExchange
Software, Circuits and PCB for microcontroller based gas exchange system
It measures 65 × 56 mm and has 2 copper layers, 1.6 mm thick.
29 parts, built around the MCP2551-I/P, LM78L05ACZ, MCP2515-I and RJ45. The full list of its parts is on this page, with links to each part's symbol and footprint where PCBKit's library has them.
From the RobertPHeller/RPi-RRCircuits repository on GitHub, at the commit this page was made from: the board is CANHat/CANHat.kicad_pcb. PCBKit opens the board in the browser, with nothing to install.
Its repository states no licence, so its author keeps all rights: ask RobertPHeller before reusing the design.