

EEE3088F HAT
See a 3D render of the PCB from KiCad below,
- Size
- 96 × 70 mm
- Copper layers
- 2
- Thickness
- 1.6 mm
- Parts
- 84
- Nets
- 133
- Pads
- 307
- Tracks, vias
- 414, 65
- Pours
- 2
- Routed
- Yes
- KiCad
- KiCad 6 (file 20211014)
- Created
- 25 Feb 2022
- Updated
- 23 May 2022
Overview
EEE3088F HAT is an open-source printed circuit board by rb-jones, from the rb-jones/EEE3088F_HAT repository on GitHub, published under the CC-BY-4.0 licence. It is a 2-layer board of 96 × 70 mm with 84 parts on 133 nets, routed with 414 tracks and 65 vias.
It is built around the ALS-PDIC15-21B/TR8, CH340G and DS18B20Z, with the AT24C256C-SSHL-T, LM393DR2GH and TP4056-42-ESOP8 among its other parts. Its parts include 24 resistors, 15 capacitors, 11 connectors, 9 diodes and 8 ICs.
Main components
11ALS-PDIC15-21B/TR8
SMD-4P,3.2x1.6mm-40℃~+85℃ 1.5V~5.5V SMD-4P,3.2x1.6mm Ambient Light Sensors ROHSEverlight ElectronicsAmbient Light SensorsCH340G
SOP-16-40℃~+85℃ 2Mbps 3.3V、5V USB 2.0 USB to UART SOP-16 USB Converters ROHSWCH (Nanjing Qinheng Microelectronics)USB ConvertersDS18B20Z
SOIC-8-55℃~+125℃ 12bit 2.5V~5.5V 750ms Single-bus ±0.4℃ SOIC-8 Temperature Sensors ROHSUMWTemperature SensorsAT24C256C-SSHL-T
SOIC-8-40℃~+85℃ 1,000,000 cycles 1.7V~5.5V 1MHz 256Kbit 40 Years 5ms Hardware write protection function、Noise suppression function I2C SOIC-8 EEPROM ROHSMicrochip TechnologyEEPROMLM393DR2GH
SOP-8ESD Protection SOP-8 Comparators ROHSonsemiComparatorsTP4056-42-ESOP8
ESOP-8-40℃~+85℃ 1 1A 2uA 4.2V 4V~8V Charging IC Lithium Battery Support ESOP-8 Battery Management ROHSTOPPOWERBattery ManagementTXS0108EPWR
UncategorisedUnknown maker1N5819WS
SOD-3231 Independent 1A 25A 40V 500uA@40V 600mV@1A SOD-323 Schottky Diodes ROHSGuangdong HottechSchottky DiodesAO3401A
SOT-231 P-Channel 14nC@10V 30V 47mΩ@10V、60mΩ@4.5V、85mΩ@2.5V 4A 55pF 645pF 80pF 900mV SOT-23 MOSFETs ROHSAlpha & Omega SemiconductorMOSFETsMMBT3904
SOT-23-55℃~+150℃ 1 NPN 100 100nA 200mA 200mW 300MHz 300mV 40V 6V NPN SOT-23 Bipolar (BJT) ROHSJiangsu Changjing Electronics Technology (CJ)Bipolar (BJT)YSX321SL
SMD3225-4PSMD3225-4P New Arrivals ROHSYXCUncategorised
README
README.mdAutonomous Plant Monitoring HAT for Discovery Board with STM32F051x8
This repository will be updated at each stage of the design process, and where necessary changes are made.
Group Members:
- Ryan Jones (JNSRYA006)
- Alex Cargill (CRGALE002)
- Devlin Trafford (TRFDEV001)
Project Details
This project is part of a project for EEE3088F in 2022
This project will design a HAT (Hardware Attached on Top) for a STM Discovery Board which uses the STM32F051x8. The use case for this HAT is for semi-autonomous indoor plant growing. It will have a temperature sensor located as close to the plant as possible as well as a light sensor facing the main direction which the plant receives light from . These sensors will connect to a STM Discovery board, which will act as the brain of the system. This design was created for small scale agricultural setups. Appropriate user stories were applied to develop the Specifications. Given these use cases, the PCB is able to:
- Monitor the temperature around a plant
- Get precise readings of the light level a plant is receiving.
See a 3D render of the PCB from KiCad below,
Repository Structure
Each sub-folder contains different aspects relating to different parts of the project
- PCB: The KiCad Project, Schematics, PCB & Layout and Project Libraries
- Firmware: Any software developed for the hardware or instructions on where to find relevant sofware in cases where it makes more sense to have this in its own dedicated repo
- Docs: Project documentation, Draft documents, ERC & DRC reports, project handins, schematic screenshot & documents and component datasheets
- Production: The final gerber files, BOM, Budget, or anything required by the fabrication houses
- Simulation: Any simulation files (SPICE) or design stage generated results (matlab or excel)
- CAD: Any 3D models or mechanical designs for enclosures or support
Hardware Requirements
- STMDiscovery Board with an STM32F051x8 μC
- 1 x MicroUSB to USB-A Cable
- 1x MiniUSB to USB-A Cable
- 8x Male to Female Jumpers
Software Requirements
- Computer
- Windows, Linux or MACOS
- STM32Cube IDE
- PuTTY
How to short the UVLO circuit
-
On the LHS of the board, remove resistor R12 & R10 using pliers and twisting and pulling the resistors
-
Q1 & IC1 (Circled in Orange) are the MOSFET & Op-Amp in the UVLO circuit that needs to be removed by soldering one end of a wire to the top pad (Pad 2) of R12 to the top pad (Pad 2) of R10 (Circled in Green)
How to connect the power module to the rest of the board
- On the top, RHS of the board, solder a wire between TP9 OR the +3V pin pad and the right hand pin of J7
- This will connect the power from the power module to the rest of the circuit
- If connected correctly, when a battery is inserted or a USB is connected, a Red diode (D9) will turn on to indicate the sensing and microcontroller sub-circuits are receiving power.
How to connect the PCB to the STMDiscovery Board
The following locations on the PCB need to be soldered to the male end of the jumper:
(Refer to the KiCad PCB file here for the exact location of these)
- PA1
- PA2
- PA9
- PA10
- PB6
- PB7
The female end of these jumpers are then connected to the corresponding pins on the STMDiscovery board.
How to connect the PCB & STMDiscovery to your computer using UART
- Download and install CH340 drivers
- Plug the device to your computer using a USB port.
- Check that the device is visible under ports in the Device Manager (for Windows),
- Create a serial connection with a baud rate of 18400bits/s in PuTTY
How to send your first data to the board!
- After connecting the board using the above instructions,
- Type “Hello HAT” into the console and press ENTER.
- The device will dump all information collected since the last time the device was connected to a USB host device in the terminal window
Contributing to this project
You're more than welcome to contribute to this project! Please take a look at our CONTRIBUTING.md file linked here
License
Parts
84| Qty | Value | Footprint | References |
|---|---|---|---|
| 11 | TestPoint | TestPoint:TestPoint_Pad_D2.0mm | TP1, TP2, TP3, TP4, TP5, TP6, TP7, TP8, TP9, TP10, TP11 |
| 9 | 0R | 0R:RESC2013X65N | R1, R2, R3, R4, R5, R10, R11, R12, R16 |
| 8 | Conn_01x02_Male | conn_Molex_01_02_vert:53398-0271 | J6, J7, J8, J9, J10, J11, J12, J13 |
| 5 | 10uF | 10uF_0804:CAPC2012X145N | C1, C2, C3, C4, C10 |
| 5 | 1k | 1k:RESC1608X55N | R8, R9, R14, R17, R18 |
| 4 | 1.5k | 4k7:RESC2013X65N | R21, R22, R23, R24 |
| 4 | 4.7k | 4k7:RESC2013X65N | R6, R7, R19, R20 |
| 3 | 10nF | Capacitor_SMD:C_0402_1005Metric | C7, C8, C9 |
| 3 | 1N5819WS | Diode_SMD:D_SOD-323 | D2, D3, D4 |
| 3 | LED | LED_SMD:LED_0805_2012Metric | D7, D8, D9 |
| 2 | 100n | Capacitor_SMD:C_0402_1005Metric | C12, C13 |
| 2 | 1u | 1uF_0804:CAPC1608X90N | C5, C6 |
| 2 | 22p | 22pF_0804:CAPC1608X90N | C14, C15 |
| 2 | Conn_01x33_Female | Connector_PinSocket_2.54mm:PinSocket_1x33_P2.54mm_Vertical | J2, J3 |
| 2 | Red LED | Red_LED:LEDC1608X70N | D1, D6 |
| 1 | 10k | 10k:RESC1005X40N | R15 |
| 1 | 18650 Battery | bat_holder:KEYSTONE-1042 | BT1 |
| 1 | 1k2 | 1k:RESC1608X55N | R13 |
| 1 | 47n | 47nF_0804:CAPC1608X90N | C11 |
| 1 | ALS-PDIC15-21B/TR8 | ALS_Light:LED-SMD_1206-4P-L3.2-W1.5-TR | U3 |
| 1 | AO3401A | AO3401A:SOT95P280X125-3N | Q2 |
| 1 | AT24C256C-SSHL-T | 3088_uC:SOIC127P600X175-8N | IC3 |
| 1 | CH340G | 3088_uC:SOIC127P600X180-16N | U4 |
| 1 | DS18B20Z | Package_SO:SOIC-8_3.9x4.9mm_P1.27mm | U2 |
| 1 | Green LED | Green_LED:LEDC1608X50N | D5 |
| 1 | HT75xx-1-SOT89 | Package_TO_SOT_SMD:SOT-89-3 | U1 |
| 1 | LM393DR2G | LMS393DRG:SOIC127P600X175-8N | IC2 |
| 1 | LOGO | 3088_aux_fps:github | G*** |
| 1 | LOGO | 3088_aux_fps:qr_code | G*** |
| 1 | MICROXNJ | 3088_power:SHOUHAN_MICROXNJ | J5 |
| 1 | MMBT3904 | Package_TO_SOT_SMD:SOT-23 | Q1 |
| 1 | TP4056-42-ESOP8 | TP4506:SOIC127P600X175-9N | IC1 |
| 1 | TXS0108EPWR | 3088_uC:SOP65P640X120-20N | IC4 |
| 1 | YSX321SL | 3088_uC:YSX321SL | Y1 |
Similar boards
- 2 layers30 × 126.9 mm

- 2 layers36.9 × 48.9 mm

RS485 Controller
tomrodinger/RS485_Controller
This integrates an ESP32-S3 module with an RS485 interface, so that it can be used to control Gearotons Servomotors or other RS485 devices
113 partsMIT - 4 layers100 × 70 mm

SEM
Serhio4522/SEM_hitachi-
Digitization of a Hitachi scanning electron microscope (SEM) — hardware design, FPGA firmware, and analog frontend schematics.
288 parts1 - 2 layers100 × 100 mm

EEE3088F PROJECT
xNiDx/EEE3088F-PROJECT
The door unlocks if there is an object in close proximity and a certain sound is pplayed for some time. This is to be paired with a device that emits a sound, which is not in the scope of this project.
64 partsMIT - 2 layers80 × 75 mm

Planta control
cesar191/diseno_PCB
diseño de una pcb de control el cual puede tener diferentes estructuras
55 parts - 2 layers100 × 100 mm

Hour meter board microfit can handroute
ilomon10/embedded-totalizer-hour-meter
ESP32 engine hour meter & totalizer: firmware, SensorFrame protocol, Node host tools, KiCad PCB and a Deno device simulator
152 parts - 4 layers42.8 × 36.8 mm

- 2 layers36 × 45.8 mm

Xiaomao
tigard-tools/xiaomao
Xiǎomāo is a development board geared toward hardware hacking and hardware implant design that can safely interfacing with a wide range of logic levels
84 parts37CERN-OHL-S-2.0
Questions
How big is the EEE3088F HAT PCB?
It measures 96 × 70 mm and has 2 copper layers, 1.6 mm thick.
What parts does the EEE3088F HAT use?
84 parts, built around the ALS-PDIC15-21B/TR8, CH340G, DS18B20Z and AT24C256C-SSHL-T. The full list of its parts is on this page, with links to each part's symbol and footprint where PCBKit's library has them.
Where can I download the EEE3088F HAT KiCad files?
From the rb-jones/EEE3088F_HAT repository on GitHub, at the commit this page was made from: the board is PCB/main/main.kicad_pcb and its schematic PCB/main/main.kicad_sch. PCBKit opens the board in the browser, with nothing to install.
Can I use the EEE3088F HAT design in my own project?
Its repository publishes it under the CC-BY-4.0 licence: you may reuse it on that licence's terms (keep the author's notice, and for a copyleft licence share your changes alike).