
IOT development board
vinod-gunda/4_layer_IOT_Development_Board
4-layer ESP32-C3 development board designed using KiCad

A compact 4-layer IoT development board built around the ESP32-C3, integrating environmental sensing, local storage, USB-C power with LiPo battery management, and a programming/debug interface on a single board.
ESP - 32 IOT PCB is an open-source printed circuit board by Raghav9git, from the Raghav9git/ESP-32-IoT-PCB-Board- repository on GitHub, published under the MIT licence. It is a 4-layer board of 90 × 54 mm with 82 parts on 88 nets, routed with 639 tracks and 72 vias.
It is built around the ESP32-C3-WROOM-02-H4, BME280 and CP2102N-A02-GQFN20R, with the MAX4466EXK+T, W25Q32JVSSIQ and GSD090012SEU among its other parts. Its parts include 31 resistors, 22 capacitors, 7 ICs, 6 diodes and 5 connectors. It belongs with the home automation and IoT boards and the ESP32 and RISC-V boards of this library.
A compact 4-layer IoT development board built around the ESP32-C3, integrating environmental sensing, local storage, USB-C power with LiPo battery management, and a programming/debug interface on a single board. Designed in KiCad 10.0.
This is a multi-domain hardware project that brings power electronics, mixed-signal sensor front-ends, digital interfaces, and RF-module integration together on one board — and routes them on a 4-layer stackup with dedicated power and ground planes.
The goal of this board is a self-contained, battery-capable IoT platform: an ESP32-C3 (Wi-Fi + BLE) as the brain, surrounded by the supporting subsystems a real IoT device needs — clean regulated power, safe battery charging, local data storage, environmental sensors, and a robust USB programming path.
It was built as a deliberate skill-development project to practice end-to-end PCB design across several engineering domains in a single, non-trivial board, rather than a series of isolated single-function boards.
MCU: ESP32-C3-WROOM-02 module — Wi-Fi + Bluetooth LE Power input: USB-C connector (power + data), with input fuse protection Battery: LiPo battery connector with onboard charge management (MCP73871) and power-path control Regulation: 3.3 V LDO (LM1117) for the logic rail, sourced from the 5 V USB rail Programming/Debug: CP2102N USB-to-UART bridge with automatic boot/reset (DTR/RTS) circuit Storage: microSD card slot (SPI) + onboard SPI flash (W25Q32) Sensors:
BME280 — temperature, humidity, barometric pressure TEMT6000 — ambient light Electret microphone + MAX4466 pre-amplifier — audio/sound level
User interface: Boot and Reset buttons (with RC debounce), status LEDs, I²C OLED display header, GPIO breakout header Debug: Test points on key SPI/SD signals Protection: USB data-line ESD protection (USBLC6) PCB: 4-layer design with dedicated power and ground planes
ItemDetailMicrocontrollerESP32-C3-WROOM-02 (Wi-Fi + BLE)PCB layers4 (signal / GND plane / power plane / signal)Power inputUSB-C (5 V) and LiPo batteryLogic rail3.3 V (LM1117 LDO)ChargingMCP73871 LiPo charger / power pathUSB–UART bridgeCP2102NStoragemicroSD (SPI) + W25Q32 SPI flashSensorsBME280, TEMT6000, MAX4466 mic ampInterfacesI²C, SPI, UART, GPIO headerDesign toolKiCad 10.0
The board is organized as a set of interacting subsystems. Each block exists for a specific reason:
USB-C delivers 5 V, passed through a fuse for input protection. The MCP73871 handles LiPo charging and automatic power-path switching between USB power and battery, so the board runs from USB when connected and from battery otherwise. The LM1117 LDO derives the clean 3.3 V logic rail from the 5 V rail. Input and output decoupling capacitors sit close to the regulator for stability.
The ESP32-C3-WROOM-02 is the core — a single-chip Wi-Fi + BLE module. It runs from the 3.3 V rail with local decoupling, and exposes the SPI, I²C, UART, and GPIO interfaces that connect to the rest of the board.
A CP2102N USB-to-UART bridge provides the serial programming/debug interface over USB-C. The DTR/RTS auto-reset circuit (two transistors) automatically drives the EN and BOOT lines during flashing, so firmware can be uploaded without manually pressing buttons — the standard ESP programming convenience circuit. USBLC6 ESD protection guards the USB data lines.
A microSD slot (SPI) provides removable local storage for data logging, and an onboard W25Q32 SPI flash offers fixed storage for configuration or firmware data. Test points on the SPI/SD lines allow probing during bring-up.
BME280 — digital environmental sensor (temperature, humidity, pressure) on the I²C/SPI bus. TEMT6000 — analog ambient light sensor feeding an ADC input. Electret mic + MAX4466 — an analog audio front-end; the MAX4466 amplifies the microphone signal to a usable level for the ADC.
The analog sensor front-ends are the mixed-signal portion of the design, where layout and grounding affect signal quality.
Boot and Reset buttons with RC debounce, status LEDs for power/operation indication, an I²C header for an OLED display, and a GPIO breakout header for expansion.
4-layer stackup with dedicated ground and power planes for clean power distribution and a solid low-impedance ground return — important on a board mixing RF, analog sensors, and digital interfaces. Mixed-signal layout — separating noisy digital and switching activity from the analog sensor front-ends. USB & ESD considerations — controlled USB data routing and dedicated ESD protection. Net classes for differentiated trace widths (power vs. signal). Test points on key debug nets for hardware bring-up. Compact, thoughtful component placement following the power and signal flow.
~80% complete.
Multi-page hierarchical schematic — complete, ERC passing Footprint assignment Component placement 4-layer stackup and plane setup Routing (power and signal) Copper zones / ground pour Final silkscreen pass (labels, polarity marks, board info) Final DRC sign-off Manufacturing output (Gerbers / drill files) Fabrication and bring-up testing
Remaining work is finishing/polish: silkscreen cleanup, a final DRC pass, and generating manufacturing files.
This project was built to practice the full PCB workflow on a realistic, multi-domain board:
Multi-page hierarchical schematic design Power electronics: LDO regulation, LiPo charge management, power-path design Mixed-signal design: analog sensor front-ends alongside digital interfaces RF module integration: ESP32-C3 placement and supporting circuitry Digital interfaces: SPI (flash, SD), I²C (sensors, OLED), UART (programming) USB & ESD: USB-C, USB-to-UART bridge, data-line protection 4-layer PCB layout: stackup, dedicated power/ground planes, copper zones Net classes, trace-width selection, and DRC-driven debugging Reading and applying datasheets for component configuration
KiCad 10.0 — schematic capture and PCB layout Component symbols, footprints, and 3D models sourced from KiCad libraries and standard component vendors
This board was built as a learning project to develop hands-on PCB design skills across power, mixed-signal, and digital domains. The design follows and adapts a published KiCad IoT development-board reference/tutorial as a starting point, which I used to study how a complete, multi-subsystem board is architected, laid out on four layers, and prepared for manufacturing.
License
Released under the MIT License. See LICENSE for details.
| Qty | Value | Footprint | References |
|---|---|---|---|
| 12 | 0.1uF | Capacitor_SMD:C_0805_2012Metric | C2, C5, C8, C10, C12, C14, C15, C16, C17, C18, C21, C22 |
| 12 | 10k | Resistor_SMD:R_0805_2012Metric | R1, R2, R19, R22, R23, R24, R25, R26, R27, R33, R34, R36 |
| 5 | 470 | Resistor_SMD:R_0805_2012Metric | R7, R8, R9, R14, R18 |
| 4 | 10uF | Capacitor_Tantalum_SMD:CP_EIA-3216-18_Kemet-A | C3, C4, C7, C13 |
| 4 | 50 | Resistor_SMD:R_0805_2012Metric | R10, R15, R16, R17 |
| 3 | 1uF | Capacitor_SMD:C_0805_2012Metric | C6, C11, C23 |
| 3 | LTST-C170KRKT | LTST-C170KRKT:DIOC200X125X110 | D1, D4, D5 |
| 2 | 4k7 | Resistor_SMD:R_0805_2012Metric | R20, R21 |
| 2 | 5k1 | Resistor_SMD:R_0805_2012Metric | R3, R4 |
| 2 | BC817 | Package_TO_SOT_SMD:SOT-23 | Q2, Q3 |
| 2 | LTST-C170KGKT | LTST-C170KGKT:DIOC200X125X110 | D2, D6 |
| 1 | 0.1uf | Capacitor_SMD:C_0805_2012Metric | C1 |
| 1 | 0ZCH0110AF2E | 0ZCH0110AF2E:FUSC3225X100N | F1 |
| 1 | 100k | Resistor_SMD:R_0805_2012Metric | R28 |
| 1 | 1k | Resistor_SMD:R_0805_2012Metric | R11 |
| 1 | 1nF | Capacitor_SMD:C_0805_2012Metric | C24 |
| 1 | 20k | Resistor_SMD:R_0805_2012Metric | R6 |
| 1 | 22k1 | Resistor_SMD:R_0805_2012Metric | R12 |
| 1 | 2k | Resistor_SMD:R_0805_2012Metric | R5 |
| 1 | 4.7uF | Capacitor_Tantalum_SMD:CP_EIA-3216-18_Kemet-A | C9 |
| 1 | 47k5 | Resistor_SMD:R_0805_2012Metric | R13 |
| 1 | B2B-PH-SM4-TB | B2B-PH-SM4-TB:JST_B2B-PH-SM4-TB | J2 |
| 1 | BME280 | Package_LGA:Bosch_LGA-8_2.5x2.5mm_P0.65mm_ClockwisePinNumbering | U2 |
| 1 | Boot | USLPT2819DT2TR:SW_USLPT2819DT2TR | S1 |
| 1 | CMC-5042PF-AC | CMC-5042PF-AC:CUI_CMC-5042PF-AC | MK1 |
| 1 | CP2102N-A02-GQFN20R | CP2102N-A02-GQFN20R:SILABS_CP2102N-A02-GQFN20R | U4 |
| 1 | Conn_01x04_Pin | Connector_PinHeader_2.54mm:PinHeader_1x05_P2.54mm_Vertical | J6 |
| 1 | Conn_01x05_Pin | Connector_PinHeader_2.54mm:PinHeader_1x05_P2.54mm_Vertical | J5 |
| 1 | ESP32-C3-WROOM-02-H4 | ESP32-C3-WROOM-02-H4:MODULE_ESP32-C3-WROOM-02-H4 | U3 |
| 1 | GSD090012SEU | GSD090012SEU:AMPHENOL_GSD090012SEU | J3 |
| 1 | LM1117MPX-3.3 | LM1117MPX-3.3:VREG_LM1117MPX-3.3 | VR1 |
| 1 | LTST-C170TBKT | LTST-C170TBKT:DIOC200X125X110 | D3 |
| 1 | MAX4466EXK | MAX4466EXK:SOT65P210X110-5N | U7 |
| 1 | MCP73871-2CAI_ML | MCP73871-2CAI_ML:QFN50P400X400X100-21N | U1 |
| 1 | Reset | USLPT2819DT2TR:SW_USLPT2819DT2TR | S2 |
| 1 | SS-52400-003 | SS-52400-003:BELFUSE_SS-52400-003 | J1 |
| 1 | TEMT6000X01 | TEMT6000X01:TRANS_TEMT6000X01 | Q1 |
| 1 | USBLC6-2SC6 | PCM_Package_TO_SOT_SMD_AKL:SOT-23-6 | U5 |
| 1 | W25Q32JVSSIQ | W25Q32JVSSIQ:SOIC127P790X216-8N | U6 |
The 79 most common of 82 parts.

vinod-gunda/4_layer_IOT_Development_Board
4-layer ESP32-C3 development board designed using KiCad

krishnaverma24/ESP32-4Layer-PCB-Design
This project is a custom-designed PCB integrating the ESP32 microcontroller with multiple sensors on a single board. The goal was to create a compact, versatile hardware platform for IoT and embedded system experiments.

ashfaque-ur-rahman/ESP32-Multi-Sensor-PCB
ESP32-based multi-sensor PCB with temperature/humidity, light, and microphone sensors — 4 layer Board — KiCad design based on Tech Explorations tutorial


aryan-asit/Telemetry-iot-project
In this project , a 4 layer custom pcb is made for Telematics

EngMeesh/ESP32_IoT_Dev_Board
A custom 4-layer IoT development board based on the ESP32-C3, featuring integrated LiPo battery management, a CP2102N USB-UART bridge, MicroSD support, and onboard environmental/audio sensors for embedded engineering…

SarthakDas2006/ESP32-C3-IoT-Embedded-Custom_PCB
4-layer ESP32-C3 based custom embedded IoT PCB featuring onboard temperature & humidity, light, and audio sensing, USB Type-C, Li-Po charging, and external flash memory.

JoseSanchez122/ESP32_custom_board
Custom ESP32-WROOM-32 PCB with DHT22 (temperature/humidity), BH1750 (light), and MPU-6050 (motion) sensors, 3.3V regulator, USB-C/battery input, Wi-Fi/Bluetooth, GPIO/I2C pins, LED, and reset button, for compact IoT…
It measures 90 × 54 mm and has 4 copper layers, 1.6 mm thick.
82 parts, built around the ESP32-C3-WROOM-02-H4, BME280, CP2102N-A02-GQFN20R and MAX4466EXK+T. The full list of its parts is on this page, with links to each part's symbol and footprint where PCBKit's library has them.
From the Raghav9git/ESP-32-IoT-PCB-Board- repository on GitHub, at the commit this page was made from: the board is Current files/ESP - 32 IOT PCB.kicad_pcb and its schematic Current files/ESP - 32 IOT PCB.kicad_sch. PCBKit opens the board in the browser, with nothing to install.
Its repository publishes it under the MIT licence: you may reuse it on that licence's terms (keep the author's notice, and for a copyleft licence share your changes alike).