Skip to the content
3214

LM1117MPX-3.3

Texas InstrumentsExtended

0℃~+125℃ 1 1.2V@(800mA) 15V 3.3V 5mA 75dB@(120Hz) 800mA Fixed Over Current Protection、Over Temperature Protection Positive SOT-223-4 Voltage Regulators - Linear, Low Drop Out (LDO) Regulators ROHS

Part id
ti/LM1117MPX-3.3
Category
Voltage Regulators, Linear, Low Drop Out (LDO) Regulators
Package
SOT-223-4
Pins
4
In stock
35,937 at JLCPCB (C9662)
Used on
51 open-source boards

Overview

The LM1117MPX-3.3 is a voltage Regulators, Linear, Low Drop Out (LDO) Regulator made by Texas Instruments in a SOT-223-4 package with 4 pins. 0℃~+125℃ 1 1.2V@(800mA) 15V 3.3V 5mA 75dB@(120Hz) 800mA Fixed Over Current Protection、Over Temperature Protection Positive SOT-223-4 Voltage Regulators - Linear, Low Drop Out (LDO) Regulators ROHS.

PCBKit's library has its KiCad symbol (dk_PMIC-Voltage-Regulators-Linear:LM1117MPX-3_3_NOPB, from Digikey) and its footprint (Source_Footprints:SOT-223, from Digikey), ready for a KiCad board. 35,937 are in stock at JLCPCB (part C9662). 51 open-source boards in 48 repositories on GitHub use it.

Symbol

1ADJ/GND2VOUT3VIN4VOUT
dk_PMIC-Voltage-Regulators-Linear:LM1117MPX-3_3_NOPBFrom Digikey

Footprint

3214
Source_Footprints:SOT-223From Digikey

From the datasheet

13
Supply, most
15 V · VIN, recommended operating max · p. 4
Supply, absolute maximum
20 V · VIN, absolute maximum · p. 4
Junction, hottest
150 °C · TJ, absolute maximum · p. 4
Takes working
5 mA · typical quiescent current, VIN ≤ 15V, TJ = 25°C · p. 6
Gives
800 mA · rated continuous output current · p. 1
Current limit
1.2 A · typical, VIN – VOUT = 5V, TJ = 25°C · p. 5
Output
3.3 V · typical fixed output, IOUT = 10mA, VIN = 5V, TJ = 25°C · p. 5
Dropout
1.1 V · typical at IOUT = 100mA, TJ = 25°C · p. 5
Dropout
1.15 V · typical at IOUT = 500mA, TJ = 25°C · p. 5
Dropout
1.2 V · typical at IOUT = 800mA, TJ = 25°C · p. 5
Junction to air (DCY)
61.6 K/W · junction to ambient · p. 4
Junction to board (DCY)
10.4 K/W · junction to board · p. 4
Junction to case (DCY)
42.5 K/W · junction to case, top · p. 4

What it is and has

2
Output current
800mA · p. 1
Protection
电流限制和热保护 · p. 1

Around it

1
cap 至少 10µF
between VOUT and GND; 钽电容器;改善瞬态响应和稳定性。 · p. 1

Specifications

49
ParameterConditionsAs printedPage
最大输入电压(VIN 至 GND) VINmax 20 V4
结温 (TJ)(2) TJmax 150 °C4
贮存温度,Tstg Tstgmin -65 · max 150 °C4
静电放电 V(ESD)人体放电模型 (HBM),符合 ANSI/ESDA/JEDEC JS-001 标准(1);±2000 Vmax 2000 V4
输入电压(VIN 至 GND) VINmax 15 V4
结温 (TJ)(1) TJLM1117min 0 · max 125 °C4
结至环境热阻 RθJADCY (SOT-223), 4 个引脚typ 61.6 °C/W4
结至外壳(顶部)热阻 RθJC(top)DCY (SOT-223), 4 个引脚typ 42.5 °C/W4
结至电路板热阻 RθJBDCY (SOT-223), 4 个引脚typ 10.4 °C/W4
结至顶部特征参数 ψJTDCY (SOT-223), 4 个引脚typ 2.9 °C/W4
结至电路板特征参数 ψJBDCY (SOT-223), 4 个引脚typ 10.3 °C/W4
输出电压 VOUTLM1117-3.3; IOUT = 10mA,VIN = 5V,TJ = 25°Cmin 3.267 · typ 3.3 · max 3.333 V5
输出电压 VOUTLM1117-3.3; 0 ≤ IOUT ≤ 800mA,4.75V ≤ VIN ≤ 10V; TJ = 25°Ctyp 3.3 V5
输出电压 VOUTLM1117-3.3; 0 ≤ IOUT ≤ 800mA,4.75V ≤ VIN ≤ 10V; 在 0°C 至 125°C 的结温范围内测得min 3.235 · max 3.365 V5
线路调节(3) ΔVOUTLM1117-3.3; IOUT = 0mA,4.75V ≤ VIN ≤ 15V; TJ = 25°Ctyp 1 mV5
线路调节(3) ΔVOUTLM1117-3.3; IOUT = 0mA,4.75V ≤ VIN ≤ 15V; 在 0°C 至 125°C 的结温范围内测得max 6 mV5
负载调节(3) ΔVOUTLM1117-3.3; VIN = 4.75V,0 ≤ IOUT ≤ 800mA; TJ = 25°Ctyp 1 mV5
负载调节(3) ΔVOUTLM1117-3.3; VIN = 4.75V,0 ≤ IOUT ≤ 800mA; 在 0°C 至 125°C 的结温范围内测得max 10 mV5
压降电压(4) VIN – VOUTIOUT = 100mA; TJ = 25°Ctyp 1.1 V5
压降电压(4) VIN – VOUTIOUT = 100mA; 在 0°C 至 125°C 的结温范围内测得max 1.2 V5
压降电压(4) VIN – VOUTIOUT = 500mA; TJ = 25°Ctyp 1.15 V5
压降电压(4) VIN – VOUTIOUT = 500mA; 在 0°C 至 125°C 的结温范围内测得max 1.25 V5
压降电压(4) VIN – VOUTIOUT = 800mA; TJ = 25°Ctyp 1.2 V5
压降电压(4) VIN – VOUTIOUT = 800mA; 在 0°C 至 125°C 的结温范围内测得max 1.3 V5
电流限值 ILIMITVIN – VOUT = 5V,TJ = 25°Cmin 800 · typ 1200 · max 1500 mA5
静态电流LM1117-3.3; VIN ≤ 15V; TJ = 25°Ctyp 5 mA6
静态电流LM1117-3.3; VIN ≤ 15V; 在 0°C 至 125°C 的结温范围内测得max 10 mA6
热调节TA = 25°C,30ms 脉冲typ 0.01 · max 0.1 %/W6
纹波调节fRIPPLE = 120Hz,VIN – VOUT = 3V,VRIPPLE = 1VPP; TJ = 25°Ctyp 75 dB6
纹波调节fRIPPLE = 120Hz,VIN – VOUT = 3V,VRIPPLE = 1VPP; 在 0°C 至 125°C 的结温范围内测得min 60 dB6
温度稳定性除非另有说明,否则 TJ = 25°Ctyp 0.5 %6
长期稳定性TA = 125°C,1000 小时typ 0.3 %6
RMS 输出噪声(VOUT 的百分比),10Hz ≤ f ≤ 10kHz; TJ = 25°Ctyp 0.003 %6
热阻 θJASOT-223; 布局 1; 顶面铜面积 0.0123 in2; 底面铜面积 0 in2typ 136 °C/W19
热阻 θJASOT-223; 布局 2; 顶面铜面积 0.066 in2; 底面铜面积 0 in2typ 123 °C/W19
热阻 θJASOT-223; 布局 3; 顶面铜面积 0.3 in2; 底面铜面积 0 in2typ 84 °C/W19
热阻 θJASOT-223; 布局 4; 顶面铜面积 0.53 in2; 底面铜面积 0 in2typ 75 °C/W19
热阻 θJASOT-223; 布局 5; 顶面铜面积 0.76 in2; 底面铜面积 0 in2typ 69 °C/W19
热阻 θJASOT-223; 布局 6; 顶面铜面积 1 in2; 底面铜面积 0 in2typ 66 °C/W19
热阻 θJASOT-223; 布局 7; 顶面铜面积 0 in2; 底面铜面积 0.2 in2typ 115 °C/W19
热阻 θJASOT-223; 布局 8; 顶面铜面积 0 in2; 底面铜面积 0.4 in2typ 98 °C/W19
热阻 θJASOT-223; 布局 9; 顶面铜面积 0 in2; 底面铜面积 0.6 in2typ 89 °C/W19
热阻 θJASOT-223; 布局 10; 顶面铜面积 0 in2; 底面铜面积 0.8 in2typ 82 °C/W19
热阻 θJASOT-223; 布局 11; 顶面铜面积 0 in2; 底面铜面积 1 in2typ 79 °C/W20
热阻 θJASOT-223; 布局 12; 顶面铜面积 0.066 in2; 底面铜面积 0.066 in2typ 125 °C/W20
热阻 θJASOT-223; 布局 13; 顶面铜面积 0.175 in2; 底面铜面积 0.175 in2typ 93 °C/W20
热阻 θJASOT-223; 布局 14; 顶面铜面积 0.284 in2; 底面铜面积 0.284 in2typ 83 °C/W20
热阻 θJASOT-223; 布局 15; 顶面铜面积 0.392 in2; 底面铜面积 0.392 in2typ 75 °C/W20
热阻 θJASOT-223; 布局 16; 顶面铜面积 0.5 in2; 底面铜面积 0.5 in2typ 70 °C/W20

Pins, by the datasheet

4
1 ADJ/GND
固定输出版本的接地引脚。 · p. 3
2 VOUT
稳压器的输出电压引脚。 · p. 3
3 VIN
稳压器的输入电压引脚。 · p. 3
4 VOUT
稳压器的输出电压引脚。 · p. 3

Open-source boards using it

51See all 51
  • 4 layers71.9 × 55.5 mmRISKYMSXCart, the printed circuit board in 3D

    RISKYMSXCart

    arkadiuszmakarenko/RISKYMSX

    RISKY MSX Cartridge based on WCH CH32V303V chip. It is 256KB cart programmed using USB Fat32 flash drive

    39 parts23
  • 4 layers32.8 × 100 mmWmk, the printed circuit board in 3D

    Wmk

    arkadiuszmakarenko/RISKYREA1200

    ReAmiga1200USBHID CH32V203C based USB HID.

    23 parts11
  • 4 layers200.5 × 70.9 mmALL, the printed circuit board in 3D

    ALL

    eddyem/IR-controller

    Clone of same project from sourceforge

    138 parts6GPL-3.0
  • 4 layers60.6 × 72.3 mmESP32, the printed circuit board in 3D

    ESP32

    KirtiChickamath/ESP32-IoT-sensor-board

    ESP32- IoT sensor board. 4-layer PCB, designed in KiCad . Features LiPo charging, USB-C, SPI flash, SD card, BME280, and more.

    90 parts2
  • 4 layers89 × 54.5 mmESP32 sensor board, the printed circuit board in 3D

    ESP32 sensor board

    andreschaparro/udemy-advanced-pcb-design-with-kicad-9

    93 parts1
  • 4 layers77.5 × 59.5 mmIOT, the printed circuit board in 3D

    IOT

    aryan-asit/Telemetry-iot-project

    In this project , a 4 layer custom pcb is made for Telematics

    85 parts1
  • 4 layers96.5 × 54.4 mmESP32-IoT, the printed circuit board in 3D

    ESP32-IoT

    ddennis18/ESP32-IoT-DevBoard

    An ESP32-C3 based IoT controller board designed in KiCad. The board combines wireless control, sensor interfaces, local storage, audio/light sensing, USB connectivity, and single-cell Li-ion battery support on a compact…

    88 parts1MIT
  • 4 layers82.9 × 53.8 mmESP32 IoT Project, the printed circuit board in 3D

    ESP32 IoT Project

    EngMeesh/ESP32_IoT_Dev_Board

    A custom 4-layer IoT development board based on the ESP32-C3, featuring integrated LiPo battery management, a CP2102N USB-UART bridge, MicroSD support, and onboard environmental/audio sensors for embedded engineering…

    92 parts1MIT

Parts like it

8

Questions

Is there a KiCad symbol and footprint for the LM1117MPX-3.3?

Yes. The symbol is dk_PMIC-Voltage-Regulators-Linear:LM1117MPX-3_3_NOPB and the footprint Source_Footprints:SOT-223, both drawn on this page. PCBKit places them on a board for you when you design with it.

What package is the LM1117MPX-3.3?

SOT-223-4, with 4 pins. Its footprint is drawn on this page.

Where is the LM1117MPX-3.3 datasheet?

Texas Instruments publishes it: the Datasheet link on this page opens it.

Where can I order the LM1117MPX-3.3?

JLCPCB lists it as part C9662, with 35,937 in stock; the sellers' links on this page open their listings.

What can replace the LM1117MPX-3.3?

Parts like it in the library: the LD1117S33C by STMicroelectronics, the AMS1117-3.3 by Advanced Monolithic Systems, the AMS1117-3.3 by UMW and the AMS1117-3.3V by MSKSEMI. Check their datasheets: a part that fits the footprint may still differ in its ratings.

Which open-source boards use the LM1117MPX-3.3?

51 boards in 48 repositories on GitHub; the most starred are listed on this page, with their KiCad files.