2 layers89 × 107.5 mm
2 layers89 × 107.5 mm
Protosync with teardrops
r8bx/protosync- Size
- 89 × 107.5 mm
- Copper layers
- 2
- Thickness
- 1.6 mm
- Parts
- 61
- Nets
- 63
- Pads
- 231
- Tracks, vias
- 456, 60
- Pours
- 248
- Routed
- Yes
- KiCad
- KiCad 9.0 (file 20241229)
- Created
- 21 May 2026
- Updated
- 22 May 2026
Overview
Protosync with teardrops is an open-source printed circuit board by r8bx, from the r8bx/protosync repository on GitHub. It is a 2-layer board of 89 × 107.5 mm with 61 parts on 63 nets, routed with 456 tracks and 60 vias.
It is built around the ADS1015IDGS, SN74LVC2G14DBV and CAT24C256LI, with the H11L1 among its other parts. Its parts include 16 resistors, 14 capacitors, 9 connectors, 8 ICs and 3 switches.
Main components
4
ADS1015IDGS
VSSOP-10-0.5mm-40℃~+125℃ 0.5LSB 12 128Hz、250Hz、490Hz、920Hz、1.6kHz、2.4kHz、3.3kHz 1MHz 2 2V~5.5V 2uA 3.3kHz 5ppm/℃ 6.144V Built-in Built-in I2C Sigma-Delta Support Yes VSSOP-10-0.5mm Analog to Digital Converters (ADC) ROHSTexas InstrumentsAnalog To Digital Converters (ADC)
SN74LVC2G14DBV
SOT-23-6-40℃~+125℃ 1.4V~3.7V 1.65V~5.5V 10uA 2 2 300mV~1.4V 32mA 32mA 4.7ns@5V,50pF 74LVC Series Schmitt trigger SOT-23-6 Inverters ROHSTexas InstrumentsInverters
CAT24C256LI
PDIP-81,000,000 cycles 1.8V~5.5V 100 Years 256Kbit 400kHz 5ms Hardware write protection function、Noise suppression function、Built-in power-on reset (POR) I2C PDIP-8 EEPROM ROHSonsemiEEPROM
H11L1
DIP-6-55℃~+100℃ 1 1.6mA 1Mbit/s 250mW 3V~15V 5kV DC DIP-6 Logic Output Optoisolators ROHSEverlight ElectronicsLogic Output Optoisolators
Parts
61| Qty | Value | Footprint | References |
|---|---|---|---|
| 6 | 1n | Capacitor_SMD:C_0805_2012Metric_Pad1.18x1.45mm_HandSolder | C7, C8, C9, C12, C13, C14 |
| 5 | 0.1u | Capacitor_SMD:C_0805_2012Metric_Pad1.18x1.45mm_HandSolder | C2, C4, C5, C6, C11 |
| 5 | AudioJack3 | footprints_global:SJ13513SMTTR | J2, J3, J4, J5, J6 |
| 4 | 10k | Resistor_SMD:R_0805_2012Metric_Pad1.20x1.40mm_HandSolder | R5, R6, R7, R13 |
| 4 | 1k | Resistor_SMD:R_0805_2012Metric_Pad1.20x1.40mm_HandSolder | R8, R9, R10, R14 |
| 4 | 1k@100 MHz | Inductor_SMD:L_0805_2012Metric_Pad1.15x1.40mm_HandSolder | FB1, FB2, FB3, FB4 |
| 4 | 3.9k | Resistor_SMD:R_0805_2012Metric_Pad1.20x1.40mm_HandSolder | R11, R12, R15, R16 |
| 4 | MountingHole_2.7mm_M2.5 | MountingHole:MountingHole_2.7mm_M2.5 | MH1, MH2, MH3, MH4 |
| 4 | SN74LVC2G14DBV | Package_TO_SOT_SMD:SOT-23-6 | U2, U3, U4, U5 |
| 3 | SW_Push | footprints_global:SW_Cherry_MX_PCB | SW1, SW2, SW3 |
| 2 | 100u | Capacitor_SMD:C_0805_2012Metric_Pad1.18x1.45mm_HandSolder | C1, C3 |
| 2 | Conn_01x02_Pin | Connector_PinHeader_2.54mm:PinHeader_1x02_P2.54mm_Vertical | J8, J9 |
| 1 | 100n | Capacitor_SMD:C_0805_2012Metric_Pad1.18x1.45mm_HandSolder | C10 |
| 1 | 10R | Resistor_SMD:R_0805_2012Metric_Pad1.20x1.40mm_HandSolder | R4 |
| 1 | 1N914 | Diode_SMD:D_MiniMELF_Handsoldering | D1 |
| 1 | 220R | Resistor_SMD:R_0805_2012Metric_Pad1.20x1.40mm_HandSolder | R2 |
| 1 | 33R | Resistor_SMD:R_0805_2012Metric_Pad1.20x1.40mm_HandSolder | R3 |
| 1 | 470R | Resistor_SMD:R_0805_2012Metric_Pad1.20x1.40mm_HandSolder | R1 |
| 1 | ADS1015IDGS | Package_SO:VSSOP-10_3x3mm_P0.5mm | U7 |
| 1 | CAT24C256 | Package_SO:TSSOP-8_4.4x3mm_P0.65mm | U6 |
| 1 | Conn_01x03_Pin | Connector_PinHeader_2.54mm:PinHeader_1x03_P2.54mm_Vertical | J7 |
| 1 | GPIO | Connector_PinSocket_2.54mm:PinSocket_2x20_P2.54mm_Vertical | J1 |
| 1 | H11L1 | Package_DIP:DIP-6_W8.89mm_SMDSocket_LongPads | U1 |
| 1 | ID_WP | Jumper:SolderJumper-2_P1.3mm_Open_Pad1.0x1.5mm | JP1 |
| 1 | lib_RV142FPF | footprints_global:RV142FPF40B120K0B10K004 | RV1 |
| 1 | ~ | footprints_global:Waveshare_2inch_LCD Module | U8 |
More from r8bx/protosync
1Similar boards
- 2 layers70 × 73.1 mm
Neopico hd
fliperama86/neopico-hd
Digital video and audio capture with HDMI output for Neo Geo MVS arcade hardware using Raspberry Pi Pico 2
37 parts90Unlicense - 4 layers68.5 × 89.9 mm
- 2 layers37 × 70.9 mm
Opendiag
maximus64/opendiag-hardware
OpenDIAG - Open Source OBD2 Interface (Hardware)
148 parts5CERN-OHL-S-2.0 - 4 layers45 × 53 mm
OpenTRV ESP
mpiraux/OpenTRV-ESP
An open-source and open-hardware thermostatic radiator valve based on the ESP32C6 and the 28BYJ-48 stepper motor.
64 parts2CERN-OHL-P-2.0 - 2 layers9.4 × 31.9 mm
Robot mainboard
offmor/RoboTheater
Code, hardware designs, and documentation for RoboTheater: A tabletop multi-robot platform that translates LLM-generated scripts into robot motion and multimedia output.
23 parts2MIT - 2 layers40 × 70 mm
KinetiCoreDC
axpaul/KinetiCoreDC
Compact STM32G0-based DC motor controller board featuring TI DRV8874 H-bridge drivers, RS485 communication, optoisolated I/O, and hardware power protection.
183 parts1CERN-OHL-S-2.0 - 4 layers140.6 × 108.1 mm
- 2 layers71.1 × 100.3 mm
Questions
How big is the Protosync with teardrops PCB?
It measures 89 × 107.5 mm and has 2 copper layers, 1.6 mm thick.
What parts does the Protosync with teardrops use?
61 parts, built around the ADS1015IDGS, SN74LVC2G14DBV, CAT24C256LI and H11L1. The full list of its parts is on this page, with links to each part's symbol and footprint where PCBKit's library has them.
Where can I download the Protosync with teardrops KiCad files?
From the r8bx/protosync repository on GitHub, at the commit this page was made from: the board is protosync-hardware/protosync_with_teardrops.kicad_pcb and its schematic protosync-hardware/buttons.kicad_sch. PCBKit opens the board in the browser, with nothing to install.
Can I use the Protosync with teardrops design in my own project?
Its repository states no licence, so its author keeps all rights: ask r8bx before reusing the design.