

ECAD for SRAD Avionics hardware
- Size
- 69.5 × 62.6 mm
- Copper layers
- 4
- Thickness
- 1.61 mm
- Parts
- 70
- Nets
- 114
- Pads
- 322
- Tracks, vias
- 596, 82
- Pours
- 9
- Routed
- Yes
- KiCad
- KiCad 8.0 (file 20240108)
- Created
- 21 Sep 2026
- Updated
- 7 Nov 2026
Overview
GPS Module is an open-source printed circuit board by Queens-Rocket-Engineering-Team, from the Queens-Rocket-Engineering-Team/av-hardware repository on GitHub. It is a 4-layer board of 69.5 × 62.6 mm with 70 parts on 114 nets, routed with 596 tracks and 82 vias.
It is built around the STM32F103CBT6, ISO1042BQDWVRQ1 and TPM8837C-SO1R, with the W25Q128JVSIQ, AMS1117-3.3 and 1N5819WS among its other parts. Its parts include 23 capacitors, 15 resistors, 9 ICs, 6 diodes and 4 connectors. It belongs with the radio and wireless boards and the STM32 boards of this library.
Main components
10STM32F103CBT6
LQFP-48(7x7)-40℃~+85℃ 128KB 12bit 20KB 2V~3.6V 32 Bit 37 72MHz ARM Cortex-M3 Built-in FLASH LQFP-48(7x7) Microcontrollers (MCU/MPU/SOC) ROHSSTMicroelectronicsMicrocontrollers (MCU/MPU/SOC)ISO1042BQDWVRQ1
SOP-8-300mil-40℃~+125℃ 1 1.71V~5.5V、4.5V~5.5V 4.1mA 5Mbps 73.4mA CAN Transceiver TXD dominant timeout、ESD protection、Undervoltage Protection、Thermal shutdown protection、Bus fault protection SOP-8-300mil Isolated CAN Transceivers ROHSTexas InstrumentsCAN TransceiversTPM8837C-SO1R
SOP-8-40℃~+125℃ 1.8V~5.5V 850mΩ SOP-8 Brushed DC Motor Drivers ROHS3PEAKBrushed DC Motor DriversW25Q128JVSIQ
SOIC-8-208mil-40℃~+85℃ 100,000 cycles 120ms@(32KB) 128Mbit 133MHz 1uA 2.7V~3.6V 20 Years 3ms Power-on reset、Hardware write protection、Software write protection、Write enable latch、Absolute write protection SPI SOIC-8-208mil NOR FLASH ROHSWinbondNOR FLASHAMS1117-3.3
SOT-223-40℃~+125℃ 0.003%Vout 1 1.1V@(800mA) 15V 1A 3.3V 5mA 72dB@(120Hz) Fixed Over Current Protection、Short Circuit Protection、Thermal shutdown Positive SOT-223 Voltage Regulators - Linear, Low Drop Out (LDO) Regulators ROHSAdvanced Monolithic SystemsVoltage Regulators - Linear, Low Drop Out (LDO) Regulators1N5819WS
SOD-3231 Independent 1A 25A 40V 500uA@40V 600mV@1A SOD-323 Schottky Diodes ROHSGuangdong HottechSchottky DiodesWS2812B
5mm X 5mm Surface Mount RGB LED with Intelligent ControlWorldsemiUncategorisedGT8E-6P-2H(55)
SMDWire To Board ConnectorHirose ElectricPS1240P02BT
插件,D=12.2mm-10℃~+70℃ 12.2mm 30V 3V 4kHz 5mm 7.8mm 70dB Passive (Externally Driven) Piezoelectric 插件,D=12.2mm Buzzers ROHSTDKBuzzersX322516MMB4SI
SMD3225-4P-40℃~+85℃ 10pF 16MHz 50Ω Crystal Oscillator ±10ppm ±20ppm SMD3225-4P Crystals ROHSYXCCrystals
README
prop/LCMHydra/README.md[Board Name]

Overview
Brief description of the board, its purpose, and its role within the [System Name] system.
Electrical Characteristics
| Parameter | Value |
|---|
Specifications
MCU
- Part:
- Architecture:
- Clock:
- Memory:
Communications
Other/Peripherals
- Sensors:
- Storage:
- Connectors:
System Partitioning
Brief, abstract overviews of the different subsystems across the board. Think of the board as the main system.
- A subsytem could be the board's power, the controlling cirucit of a main peripheral, etc.
[Partition Name]
Description of the subsytem and its function.
[Partition Name]
Description of the substeym and its function.
...
Hardware
Major Hardware Components
- [Component]: Description ...
Major Circuits
[Circuit]
- Description, supporting calculations, snippet of circuit.
History
- Any relevant information on the board's histroy: issues, etc.
Status
Status: [Development / Review / Shipped / Assembly / Testing / Validated / ]
Revision: [Revision]
Changelog
[Revision]
- Description of change | Date
- Description of change | Date ...
QRET, 2026-2027
Parts
70| Qty | Value | Footprint | References |
|---|---|---|---|
| 4 | 100n | Capacitor_SMD:C_0402_1005Metric | C11, C14, C15, C16 |
| 4 | 1uF | Capacitor_SMD:C_0603_1608Metric | C1, C2, C4, C6 |
| 3 | 100nF | Capacitor_SMD:C_0603_1608Metric | C7, C13, C21 |
| 3 | 10k | Resistor_SMD:R_0603_1608Metric | R2, R3, R13 |
| 3 | 10uF | Capacitor_SMD:C_0603_1608Metric | C19, C28, C29 |
| 3 | LM66100DCKR | LMR66100:SC-70-6_Handsoldering | U4, U5, U6 |
| 2 | 0.1u | Capacitor_SMD:C_0603_1608Metric | C8, C9 |
| 2 | 100k | Resistor_SMD:R_0603_1608Metric | R19, R20 |
| 2 | 10p | Capacitor_SMD:C_0603_1608Metric | C3, C20 |
| 2 | 1N5819WS | Diode_SMD:D_SOD-323 | D1, D2 |
| 2 | 1uF | Capacitor_SMD:C_0805_2012Metric | C12, C18 |
| 2 | 2.2k | Resistor_SMD:R_0603_1608Metric | R5, R6 |
| 2 | 5.1k | Resistor_SMD:R_0603_1608Metric | R14, R15 |
| 2 | WS2812B | LED_SMD:LED_WS2812B_PLCC4_5.0x5.0mm_P3.2mm | D5, D9 |
| 1 | 1.5k | Resistor_SMD:R_0603_1608Metric | R8 |
| 1 | 100R | Resistor_SMD:R_0805_2012Metric | FB1 |
| 1 | 100uF | Capacitor_SMD:CP_Elec_6.3x5.9 | C5 |
| 1 | 10n | Capacitor_SMD:C_0603_1608Metric | C17 |
| 1 | 10uF | Capacitor_SMD:CP_Elec_4x5.4 | C10 |
| 1 | 1k | Resistor_SMD:R_0603_1608Metric | R16 |
| 1 | 22k | Resistor_SMD:R_0603_1608Metric | R1 |
| 1 | 3.3k | Resistor_SMD:R_0603_1608Metric | R4 |
| 1 | 3V3 | TestPoint:TestPoint_Pad_1.5x1.5mm | TP7 |
| 1 | 47k | Resistor_SMD:R_0603_1608Metric | R10 |
| 1 | 680 | Resistor_SMD:R_0603_1608Metric | R7 |
| 1 | AMS1117-3.3 | Package_TO_SOT_SMD:SOT-223-3_TabPin2 | U10 |
| 1 | CP2102N-Axx-xQFN28 | Package_DFN_QFN:QFN-28-1EP_5x5mm_P0.5mm_EP3.35x3.35mm | U2 |
| 1 | DB_LED (YLW) | LED_SMD:LED_0603_1608Metric | D8 |
| 1 | GND | TestPoint:TestPoint_Pad_1.5x1.5mm | TP6 |
| 1 | GT8E-6P-2H(55) | footprints:CONN_GT8E-6P-2H(55) | J1 |
| 1 | ISO1042BQDWVR | ISO1042:SOIC-8 ISO1042BDWV | U9 |
| 1 | PA2 | TestPoint:TestPoint_Pad_1.5x1.5mm | TP10 |
| 1 | PA3 | TestPoint:TestPoint_Pad_1.5x1.5mm | TP11 |
| 1 | PA4 | TestPoint:TestPoint_Pad_1.5x1.5mm | TP4 |
| 1 | PS1240P02BT | footprints:Buzzer_12.6x9.5RM5.0 | BZ1 |
| 1 | PWR_LED (GRN) | LED_SMD:LED_0805_2012Metric | D4 |
| 1 | STM32F103CBT6 | Package_QFP:LQFP-48_7x7mm_P0.5mm | U1 |
| 1 | SWD_01x04_Pin | SWD_Header:SWD_PinHeader_1x04_P2.54mm_Horizontal_SMD | J2 |
| 1 | SW_STM_BOOT_MODE | Button_Switch_SMD:SW_Push_1P1T_XKB_TS-1187A | SW2 |
| 1 | SW_STM_RESET | Button_Switch_SMD:SW_Push_1P1T_XKB_TS-1187A | SW1 |
| 1 | Stack Male Edge Connector | Connector_PCBEdge:BUS_PCIexpress_x1 | J4 |
| 1 | TPM8837C-SO1R | footprints:SOP-8_TPK | U7 |
| 1 | USB_C_Female_USB2_Small | footprints:USB_C_DB-108PWB | J6 |
| 1 | VSTACK | TestPoint:TestPoint_Pad_1.5x1.5mm | TP1 |
| 1 | VSWD | TestPoint:TestPoint_Pad_1.5x1.5mm | TP3 |
| 1 | VUSB | TestPoint:TestPoint_Pad_1.5x1.5mm | TP2 |
| 1 | W25Q128JVS | Package_SO:SOIC-8_5.23x5.23mm_P1.27mm | U3 |
| 1 | X322516MMB4SI | Crystal:Crystal_SMD_3225-4Pin_3.2x2.5mm | Y1 |
More from Queens-Rocket-Engineering-Team/av-hardware
6- 4 layers69.5 × 60 mm

- 2 layers141.6 × 70 mm

- 4 layers69.5 × 62.6 mm

- 4 layers69.5 × 62.6 mm

- 2 layers50 × 65 mm

- 2 layers69.5 × 98.5 mm

Similar boards
- 4 layers69.5 × 62.6 mm

Sensors Module
Queens-Rocket-Engineering-Team/Avionics-23-26
QRET Avionics hardware, firmware, and documentation for 2023 to 2025.
197 parts4 - 4 layers69.5 × 62.6 mm

Power Module
Queens-Rocket-Engineering-Team/av-power
QRET Avionics PCBs and firmware for delivering power to SRAD PCBs
136 parts1 - 4 layers42 × 65 mm

Icarus Flight Computer
daedalus-ind/icarus-hardware
Hardware of the onboard flight computer for the Icarus rocket.
106 parts2MIT - 2 layers37 × 37 mm

F7FC
Momozavur/F7FC-V0.1
Open the appropriate .kicadpro file in KiCad; .pro entries are legacy projects. Keep schematics, boards, local libraries, library tables, and supporting files together.
69 parts - 4 layers130 × 85 mm

Rapid Core RCP
Arockiyalipson/Rapid-CoreX
A PCB Board with Various Communication protocols
170 partsMIT - 2 layers175 × 120 mm

JackOfAllTradesV2p0
czalinski/ThlHwTestDevices
KiCad designs, firmware and documentation for circuits that support testing of electrical hardware, such as HASS and HALT testing.
172 partsMIT - 2 layers87 × 75 mm

Stylophone
VikeshSubra/FreesideElectronics
Circuits, code, and docs related to projects and classes for the Freeside Atlanta Makerspace
80 parts - 2 layers154.7 × 113 mm

DeskMixer
RaduAndre/DeskMixer
DeskMixer is a software that allows control of application volumes with real sliders, and action mapping on buttons using arduino like platforms. The project was inspired originally by deej.
113 parts3
Questions
How big is the GPS Module PCB?
It measures 69.5 × 62.6 mm and has 4 copper layers, 1.61 mm thick.
What parts does the GPS Module use?
70 parts, built around the STM32F103CBT6, ISO1042BQDWVRQ1, TPM8837C-SO1R and W25Q128JVSIQ. The full list of its parts is on this page, with links to each part's symbol and footprint where PCBKit's library has them.
Where can I download the GPS Module KiCad files?
From the Queens-Rocket-Engineering-Team/av-hardware repository on GitHub, at the commit this page was made from: the board is recovery/GPSModule/GPS_Module.kicad_pcb and its schematic libraries/prop/PT_module.kicad_sch. PCBKit opens the board in the browser, with nothing to install.
Can I use the GPS Module design in my own project?
Its repository states no licence, so its author keeps all rights: ask Queens-Rocket-Engineering-Team before reusing the design.