2 layers21.3 × 52 mm
2 layers60.1 × 97.1 mm
Pideck
piraticus/piDeck- Size
- 60.1 × 97.1 mm
- Copper layers
- 2
- Thickness
- 1.6 mm
- Parts
- 43
- Nets
- 296
- Pads
- 469
- Tracks, vias
- 0, 0
- Routed
- Not yet
- KiCad
- KiCad 9.0 (file 20241229)
- Created
- 27 Mar 2025
- Updated
- 11 Jul 2025
Overview
Pideck is an open-source printed circuit board by piraticus, from the piraticus/piDeck repository on GitHub. It is a 2-layer board of 60.1 × 97.1 mm with 43 parts on 296 nets.
It is built around the RP2040, GD25Q16ETIGR and RT9742GGJ5, with the RT9742SNGV, TXS0108EPW and ABM8-272-T3 among its other parts. Its parts include 23 capacitors, 7 resistors, 6 ICs, 4 connectors and 1 crystal. It belongs with the RP2040 and Raspberry Pi (Linux) boards of this library.
Main components
8
RP2040
LQFN-56(7x7)12bit 133MHz 30 LQFN-56(7x7) Microcontrollers (MCU/MPU/SOC) ROHSRaspberry PiMicrocontrollers (MCU/MPU/SOC)
GD25Q16ETIGR
SOP-8-40℃~+85℃ 100,000 cycles 11uA 133MHz 150ms@(32KB) 16Mbit 2.7V~3.6V 20 Years 400us SPI SOP-8 NOR FLASH ROHSGigaDevice Semicon BeijingNOR FLASH
RT9742GGJ5
TSOT-23-5-40℃~+85℃ 1 1A 2.7V~6V 70mΩ Active High High Side Switch Short-Circuit Protection(SCP)、Undervoltage Protection(UVP)、Overcurrent Protection(OCP)、Over Temperature Protection TSOT-23-5 Power Distribution Switches ROHSRichtek TechPower Distribution Switches
RT9742SNGV
SOT-23-3-40℃~+85℃ 1 2.7V~6V 500mA 70mΩ Active High High Side Switch Short-Circuit Protection(SCP)、Undervoltage Protection(UVP)、Overcurrent Protection(OCP)、Over Temperature Protection SOT-23-3 Power Distribution Switches ROHSRichtek TechPower Distribution Switches
TXS0108EPW
TSSOP-20-40℃~+85℃ 1 1.4V~3.6V 1.65V~5.5V 60Mbps 8 Automatic direction detection、Output enable high-impedance、Integrated pull-up resistor Bidirectional Level translator Push-Pull、Open-drain TSSOP-20 Translators, Level Shifters ROHSTexas InstrumentsTranslators, Level Shifters
ABM8-272-T3
SMD3225-4P-40℃~+85℃ 10pF 12MHz 50Ω SMD crystal oscillator ±30ppm ±30ppm SMD3225-4P Crystals ROHSAbraconCrystals
ARJM11D7-502-AB-EW2
插件-40℃~+85℃ 1 Gold Non-PoE Phosphor bronze RJ45 Jack Right Angle Shielded With LED 插件 Ethernet Connectors / Modular Connectors (RJ45 RJ11) ROHSAbraconEthernet Connectors / Modular Connectors (RJ45 RJ11)
BAT-HLD-001-THM
插件插件 Button And Strip Battery Connector ROHSTE ConnectivityButton And Strip Battery Connector
README
README.mdpiDeck
Parts
43| Qty | Value | Footprint | References |
|---|---|---|---|
| 13 | 100nF | Capacitor_SMD:C_0603_1608Metric_Pad1.08x0.95mm_HandSolder | C4, C5, C7, C8, C9, C10, C11, C12, C13, C14, C20, C22, C23 |
| 7 | 1uF | Capacitor_SMD:C_0603_1608Metric_Pad1.08x0.95mm_HandSolder | C1, C2, C3, C6, C15, C18, C19 |
| 2 | 10K | Resistor_SMD:R_0603_1608Metric_Pad0.98x0.95mm_HandSolder | R1, R3 |
| 2 | 15pF | Capacitor_SMD:C_0603_1608Metric_Pad1.08x0.95mm_HandSolder | C16, C17 |
| 2 | 27.4k | Resistor_SMD:R_0603_1608Metric_Pad0.98x0.95mm_HandSolder | R4, R5 |
| 2 | 470 | Resistor_SMD:R_0603_1608Metric_Pad0.98x0.95mm_HandSolder | R6, R7 |
| 1 | 10uF | Capacitor_SMD:C_0603_1608Metric_Pad1.08x0.95mm_HandSolder | C21 |
| 1 | 1k | Resistor_SMD:R_0603_1608Metric_Pad0.98x0.95mm_HandSolder | R2 |
| 1 | ABM8-272-T3 | ABM8-272-T3:ABM8-272-T3_ABR | X1 |
| 1 | AP7312-1828W6-7 | AP7312-1828W6-7:SOT26_DIO | U2 |
| 1 | ARJM11D7-502-AB-EW2 | ARJM11D7-502-AB-EW2:ABRACON_ARJM11D7-502-AB-EW2 | J2 |
| 1 | BAT-HLD-001-THM | BAT-HLD-001-THM:BAT_BAT-HLD-001-THM | BT1 |
| 1 | BM20B_0.8_-34DS-0.4V_53_ | HIROSE_BM20B_0.8_-34DS-0.4V_53_:HIROSE_BM20B_0.8_-34DS-0.4V_53_ | J1 |
| 1 | ComputeModule5-CM5 | CM5IO:Raspberry-Pi-5-Compute-Module | Module1 |
| 1 | GD25Q16ETIGR | Package_SO:SOP-8_3.9x4.9mm_P1.27mm | U3 |
| 1 | HDMI_D_1.4 | Connector_Video:HDMI_Micro-D_Molex_46765-1x01 | J3 |
| 1 | Micro_SD_Card_Det2 | Connector_Card:microSD_HC_Hirose_DM3AT-SF-PEJM5 | J4 |
| 1 | RP2040 | Package_DFN_QFN:QFN-56-1EP_7x7mm_P0.4mm_EP3.2x3.2mm | U1 |
| 1 | RT9742GGJ5 | Package_TO_SOT_SMD:SOT-23-5 | U4 |
| 1 | RT9742SNGV | Package_TO_SOT_SMD:TSOT-23_HandSoldering | U6 |
| 1 | TXS0108EPW | Package_SO:TSSOP-20_4.4x6.5mm_P0.65mm | U5 |
More from piraticus/piDeck
1Similar boards
- 2 layers100 × 100 mm
- 4 layers50 × 16 mm
System board
proegssilb/lightsaber-hardware
PCBs and other files for lightsaber soundboard hardware.
72 parts2CERN-OHL-S-2.0 - 8 layers74 × 128 mm
Limejig
taskx6004/limejig
Open-source LimeJig fixture firmware, host tools, KiCad source, and synthetic test examples
92 parts1MIT - 6 layers125 × 125 mm
Libreboard broken
256foundation/libreboard
Open Source Bitcoin Mining Control Board
193 parts21CERN-OHL-S-2.0 - 4 layers80 × 70 mm
CM4IOv5
vega-d/CM4-nano-carrierboard
A simplified carrier board for RPI CM4 module featuring reduced footprint.
66 parts11GPL-3.0 - 6 layers47 × 105 mm
CompactPi
loganrf/compactPi
compactPi is a project to develop a compact Raspberry Pi Compute Module carrier suitable for ArduPilot applications. It's primarily targeted at marine applications (ArduSub/ArduRover).
127 parts2CERN-OHL-S-2.0 - 4 layers59.7 × 78 mm
CM5IO
Distaff/RPi_CM_Drone_Board
Source of the CM5-based drone controller used for onboard image processing, communication, and high-level automation. Originally created for IARC2026 (drone engineering competition), used in other competitions as well.
65 parts1MIT - 4 layers100 × 100 mm
Netherrack
nimitvijayvargee/netherrack
A Compute Module 5 Carrier board to use as a minecraft server!
65 parts1MIT
Questions
How big is the Pideck PCB?
It measures 60.1 × 97.1 mm and has 2 copper layers, 1.6 mm thick.
What parts does the Pideck use?
43 parts, built around the RP2040, GD25Q16ETIGR, RT9742GGJ5 and RT9742SNGV. The full list of its parts is on this page, with links to each part's symbol and footprint where PCBKit's library has them.
Where can I download the Pideck KiCad files?
From the piraticus/piDeck repository on GitHub, at the commit this page was made from: the board is electronics/pideck/pideck.kicad_pcb and its schematic electronics/keyboard_hat/pideck.kicad_sch. PCBKit opens the board in the browser, with nothing to install.
Can I use the Pideck design in my own project?
Its repository states no licence, so its author keeps all rights: ask piraticus before reusing the design.