
Ladcp star circuit
pedrolpena/ladcp_interface
Break out boards to make charging and configuring LADCP's cleaner and easier.

Break out boards to make charging and configuring LADCP's cleaner and easier.
Ladcp interface box is an open-source printed circuit board by pedrolpena, from the pedrolpena/ladcp_interface repository on GitHub, published under the GPL-3.0 licence. It is a 2-layer board of 92 × 41 mm with 42 parts on 64 nets, routed with 308 tracks and 41 vias.
It is built around the MAX3232ID and FT4232HL. Its parts include 22 capacitors, 7 connectors, 4 ICs, 2 resistors and 1 crystal. It belongs with the interfaces and adapters boards of this library.
| Qty | Value | Footprint | References |
|---|---|---|---|
| 16 | .1uF | Capacitor_SMD:C_0805_2012Metric_Pad1.18x1.45mm_HandSolder | C1, C2, C4, C5, C6, C7, C8, C9, C10, C11, C12, C15, C16, C17, C18, C19 |
| 3 | 4.7uF | Capacitor_Tantalum_SMD:CP_EIA-2012-12_Kemet-R_Pad1.30x1.05mm_HandSolder | C13, C14, C20 |
| 2 | FerriteBead_Small | Inductor_SMD:L_0805_2012Metric_Pad1.15x1.40mm_HandSolder | FB1, FB2 |
| 2 | MountingHole | MountingHole:MountingHole_2.1mm | H1, H2 |
| 1 | +12V | TerminalBlock_Phoenix:TerminalBlock_Phoenix_PT-1,5-2-5.0-H_1x02_P5.00mm_Horizontal | J7 |
| 1 | 12K | Resistor_SMD:R_0805_2012Metric_Pad1.20x1.40mm_HandSolder | R2 |
| 1 | 12V LDO | Package_TO_SOT_SMD:SOT-23 | U5 |
| 1 | 1K | Resistor_SMD:R_0805_2012Metric_Pad1.20x1.40mm_HandSolder | R1 |
| 1 | 3.3V regulator | Package_TO_SOT_SMD:TO-252-3_TabPin2 | U2 |
| 1 | 3.3uF | Capacitor_SMD:C_0805_2012Metric_Pad1.18x1.45mm_HandSolder | C3 |
| 1 | 50V 10uF | Capacitor_THT:CP_Radial_D6.3mm_P2.50mm | C22 |
| 1 | 50V 1uF | Capacitor_THT:CP_Radial_D4.0mm_P1.50mm | C21 |
| 1 | AMMETER | TerminalBlock_Phoenix:TerminalBlock_Phoenix_PT-1,5-2-5.0-H_1x02_P5.00mm_Horizontal | J5 |
| 1 | CHARGER | TerminalBlock_Phoenix:TerminalBlock_Phoenix_PT-1,5-2-5.0-H_1x02_P5.00mm_Horizontal | J3 |
| 1 | CRYSTAL | Oscillator:Oscillator_SMD_ECS_2520MV-xxx-xx-4Pin_2.5x2.0mm | X1 |
| 1 | FT4232H | Package_QFP:LQFP-64_10x10mm_P0.5mm | U1 |
| 1 | LOGO | ladcp_interface_box:noaa_logo_8x8 | G*** |
| 1 | LOGO | ladcp_interface_box:noaa_logo | G*** |
| 1 | MAX3232 | Package_SO:TSSOP-16_4.4x5mm_P0.65mm | U3 |
| 1 | SWITCH | TerminalBlock_Phoenix:TerminalBlock_Phoenix_PT-1,5-2-5.0-H_1x02_P5.00mm_Horizontal | J4 |
| 1 | TERM BLK 8POS SIDE ENTRY 5MM PCB | TerminalBlock_Phoenix:TerminalBlock_Phoenix_PT-1,5-8-5.0-H_1x08_P5.00mm_Horizontal | J1 |
| 1 | USB_B_Mini | Connector_USB:USB_Mini-B_Wuerth_65100516121_Horizontal | J2 |
| 1 | VOLT METER | TerminalBlock_Phoenix:TerminalBlock_Phoenix_PT-1,5-2-5.0-H_1x02_P5.00mm_Horizontal | J6 |

pedrolpena/ladcp_interface
Break out boards to make charging and configuring LADCP's cleaner and easier.



m1geo/Quad-AMBE3000
A PCB for four DVSI AMBE-3000R Vocoders for use with WebSDRs/Audio transcoding


jamesfowkes/quad-serial-breakout
A quad USB-to-serial breakout board based on the FT4232 IC


coon42/magic-lantern-dev-kit
A dev kit for connection and communication with the service port of Canon EOS cameras.

esl-epfl/x-heep-programmer-pmod
PMOD integrating an external SPI flash and an FTDI based programmer for the flash & JTAG debugger for x-heep
It measures 92 × 41 mm and has 2 copper layers, 1.6 mm thick.
42 parts, built around the MAX3232ID and FT4232HL. The full list of its parts is on this page, with links to each part's symbol and footprint where PCBKit's library has them.
From the pedrolpena/ladcp_interface repository on GitHub, at the commit this page was made from: the board is ladcp_interface_box/ladcp_interface_box/ladcp_interface_box.kicad_pcb and its schematic ladcp_interface_box/ladcp_interface_box/ladcp_interface_box.kicad_sch. PCBKit opens the board in the browser, with nothing to install.
Its repository publishes it under the GPL-3.0 licence: you may reuse it on that licence's terms (keep the author's notice, and for a copyleft licence share your changes alike).