

Core v mini mcu spiboot fpga
PMOD integrating an external SPI flash and an FTDI based programmer for the flash & JTAG debugger for x-heep
- Size
- 38.5 × 40 mm
- Copper layers
- 4
- Thickness
- 4.69 mm
- Parts
- 39
- Nets
- 58
- Pads
- 201
- Tracks, vias
- 539, 60
- Pours
- 3
- Routed
- Yes
- KiCad
- KiCad 6 (file 20211014)
- Created
- 6 Mar 2023
- Updated
- 6 Mar 2023
Overview
Core v mini mcu spiboot fpga is an open-source printed circuit board by esl-epfl, from the esl-epfl/x-heep-programmer-pmod repository on GitHub, published under the CC-BY-SA-4.0 licence. It is a 4-layer board of 38.5 × 40 mm with 39 parts on 58 nets, routed with 539 tracks and 60 vias.
It is built around the FT4232HL and LP2985-33DBV. Its parts include 18 capacitors, 9 resistors, 3 ICs, 3 connectors and 2 inductors. It belongs with the interfaces and adapters and fPGA and programmable logic boards and the FPGA and CPLD boards of this library.
Main components
2FT4232HL
QFP64Quad High Speed USB to Multipurpose UART/MPSSE ICFTDIUncategorisedLP2985-33DBV
SOT-23-5-40℃~+125℃@(Tj) 1 150mA 16V 3.3V 30uVrms 45dB@(1kHz) 575mV@(150mA) 850uA Fixed Over Current Protection、Short Circuit Protection、Thermal shutdown、Enable control、Noise bypass terminal Positive SOT-23-5 Voltage Regulators - Linear, Low Drop Out (LDO) Regulators ROHSTexas InstrumentsVoltage Regulators - Linear, Low Drop Out (LDO) Regulators
README
README.mdThis repository contains the HEEP programmer PMOD
This PMOD pcb provides the following features:
- An OpenOCD compatible JTAG programmer for debugging the RISC-V core
- An 128 MBIT (Q)SPI flash chip as well as an iceprog compatible programmer for the flash (the programmer has been derived from the excellent icebreaker board)
- Two UARTs

Parts
39| Qty | Value | Footprint | References |
|---|---|---|---|
| 11 | 100n | Capacitor_SMD:C_0603_1608Metric | C1, C2, C3, C4, C6, C9, C10, C11, C12, C13, C14 |
| 6 | 10k | Resistor_SMD:R_0603_1608Metric | R7, R9, R10, R11, R12, R13 |
| 2 | 30p | Capacitor_SMD:C_0603_1608Metric | C15, C16 |
| 2 | 4.7u | Capacitor_SMD:C_0805_2012Metric | C7, C8 |
| 2 | 600n | Inductor_SMD:L_0805_2012Metric | L1, L2 |
| 2 | Conn_02x06_Odd_Even | Connector_PinHeader_2.54mm:PinHeader_2x06_P2.54mm_Horizontal | PMOD1, PMOD2 |
| 1 | 10n | Capacitor_SMD:C_0603_1608Metric | C17 |
| 1 | 10u | Capacitor_SMD:C_0603_1608Metric | C18 |
| 1 | 12k 1% | Resistor_SMD:R_0603_1608Metric | R6 |
| 1 | 2k2 | Resistor_SMD:R_0603_1608Metric | R8 |
| 1 | 3.3u | Capacitor_SMD:C_0805_2012Metric | C5 |
| 1 | 51k | Resistor_SMD:R_0603_1608Metric | R1 |
| 1 | Conn_01x02 | Connector_PinHeader_2.54mm:PinHeader_1x02_P2.54mm_Vertical | JSPICS1 |
| 1 | Conn_01x03 | Connector_PinHeader_2.54mm:PinHeader_1x03_P2.54mm_Vertical | J2 |
| 1 | Conn_02x10_Odd_Even | Connector_PinHeader_2.54mm:PinHeader_2x10_P2.54mm_Vertical | J1 |
| 1 | Crystal_GND24 | Crystal:Crystal_SMD_3225-4Pin_3.2x2.5mm | Y1 |
| 1 | FT4232HL | Package_QFP:LQFP-64_10x10mm_P0.5mm | U2 |
| 1 | LP2985-3.3 | Package_TO_SOT_SMD:SOT-23-5 | U4 |
| 1 | USB Micro | Connector_USB:USB_Micro-B_Molex-105017-0001 | P1 |
| 1 | W25Q | Package_SO:SOIC-8_5.23x5.23mm_P1.27mm | U3 |
Similar boards
- 2 layers58.4 × 50 mm

- 2 layers170 × 170 mm

- 4 layers84 × 62 mm

Quad AMBE3000
m1geo/Quad-AMBE3000
A PCB for four DVSI AMBE-3000R Vocoders for use with WebSDRs/Audio transcoding
200 parts19MIT - 4 layers60 × 60 mm

- 2 layers50 × 50 mm

Quad serial
jamesfowkes/quad-serial-breakout
A quad USB-to-serial breakout board based on the FT4232 IC
53 parts15 - 4 layers144.3 × 143.8 mm

- 2 layers100 × 73.2 mm

Ml dev board
coon42/magic-lantern-dev-kit
A dev kit for connection and communication with the service port of Canon EOS cameras.
56 parts8 - 2 layers79.5 × 50 mm

Questions
How big is the Core v mini mcu spiboot fpga PCB?
It measures 38.5 × 40 mm and has 4 copper layers, 4.69 mm thick.
What parts does the Core v mini mcu spiboot fpga use?
39 parts, built around the FT4232HL and LP2985-33DBV. The full list of its parts is on this page, with links to each part's symbol and footprint where PCBKit's library has them.
Where can I download the Core v mini mcu spiboot fpga KiCad files?
From the esl-epfl/x-heep-programmer-pmod repository on GitHub, at the commit this page was made from: the board is pcb/core-v-mini-mcu-spiboot-fpga.kicad_pcb and its schematic pcb/core-v-mini-mcu-spiboot-fpga.kicad_sch. PCBKit opens the board in the browser, with nothing to install.
Can I use the Core v mini mcu spiboot fpga design in my own project?
Its repository publishes it under the CC-BY-SA-4.0 licence: you may reuse it on that licence's terms (keep the author's notice, and for a copyleft licence share your changes alike).