Skip to the content
4 layers84 × 62 mmQuad AMBE3000, the printed circuit board in 3D

A PCB for four DVSI AMBE-3000R Vocoders for use with WebSDRs/Audio transcoding

Size
84 × 62 mm
Copper layers
4
Thickness
1.6 mm
Parts
200
Nets
381
Pads
1,083
Tracks, vias
1,747, 465
Pours
10
Routed
Yes
KiCad
KiCad 7 (file 20221018)
Created
20 Feb 2024
Updated
12 Mar 2024

Overview

Quad AMBE3000 is an open-source printed circuit board by m1geo, from the m1geo/Quad-AMBE3000 repository on GitHub, published under the MIT licence. It is a 4-layer board of 84 × 62 mm with 200 parts on 381 nets, routed with 1,747 tracks and 465 vias.

It is built around the 74AVC9112DCH, TPS7A8001DRBR and 74HC595D, with the AT93C46D-TH-T, FT4232HL and AO3400A among its other parts. Its parts include 108 capacitors, 49 resistors, 10 ICs, 9 diodes and 5 transistors. It belongs with the audio and music boards of this library.

Main components

6

README

README.md

Quad-AMBE3000

A PCB for four DVSI AMBE-3000R (or AMBE-3003) Vocoders for use with WebSDRs/Audio transcoding.

Using four AMBE-3000R parts was cheaper than using a single AMBE-3003, which was the original plan. This is useful for VHF, UHF, SHF WebSDR platforms that decode D-Star, DMR, YSF, NXDN, P25, etc. A soft-codec approach based on mbelib can be used, but appeared to give poorer decode audio when tested.

Using four AMBE-3003 parts gives a total of 12 similtaneous transcode streams. the '3003 part requires 1V9 instead of 1V8. You may also benefit from increasing the S_COM_RATE to 921,600kbps, by changing S_COM_RATE0 from low to high. See the devices respective datasheets.

The DVSI AMBE parts can be purchased in low volume from the DVSI Inc. Hardware Product Pricing page. You will need to create a purchase order to buy from DVSI.

Assembly

The design schematic include details for JLCPCB assembly, who assembled mine. You'll likely have to reflow the DVSI AMBE-3000R part yourself, which I did with a PCB reflow hotplate, but you can do any way you wish.

Each schematic component has a JLCPCB Parts/LCSC part number (Cxxxxxx), which can be exported to the BoM using the extra field "LCSC".

Schematic

PDF schematic can be found here

Images

Front PCB

OpenWebRX CodecServer

3D Renders

Front Render

Rear Render

Parts

200
QtyValueFootprintReferences
82100nCapacitor_SMD:C_0603_1608MetricC1, C11, C101, C102, C103, C104, C105, C106, C107, C108, C109, C110, C111, C112, C114, C115 +66
1710kResistor_SMD:R_0603_1608MetricR17, R18, R20, R25, R29, R30, R31, R34, R35, R36, R39, R40, R41, R44, R45, R46 +1
1210uCapacitor_SMD:C_0603_1608MetricC33, C34, C37, C54, C55, C58, C75, C76, C79, C96, C97, C100
104u7Capacitor_SMD:C_0603_1608MetricC6, C8, C15, C21, C22, C25, C27, C28, C29, C32
9330RResistor_SMD:R_0603_1608MetricR9, R10, R11, R12, R13, R14, R15, R16, R49
533RResistor_SMD:R_0603_1608MetricR1, R2, R3, R4, R5
5AO3400APackage_TO_SOT_SMD:SOT-23Q1, Q2, Q3, Q4, Q5
424k9Resistor_SMD:R_0603_1608MetricR32, R37, R42, R47
45R1Resistor_SMD:R_0603_1608MetricR33, R38, R43, R48
4600R/100MInductor_SMD:L_0805_2012MetricFB1, FB2, FB3, FB4
4AMBE-3000RPackage_QFP:LQFP-128_14x14mm_P0.4mmU7, U8, U9, U10
4GRNLED_SMD:LED_0603_1608MetricD1, D3, D5, D7
4HW RSTJumper:SolderJumper-2_P1.3mm_Open_RoundedPad1.0x1.5mmJP1, JP2, JP3, JP4
4M3MountingHole:MountingHole_3.2mm_M3_Pad_ViaH1, H2, H3, H4
4REDLED_SMD:LED_0603_1608MetricD2, D4, D6, D8
330k9Resistor_SMD:R_0603_1608MetricR23, R24, R26
210nCapacitor_SMD:C_0603_1608MetricC23, C30
212kResistor_SMD:R_0603_1608MetricR22, R28
21kResistor_SMD:R_0603_1608MetricR19, R21
230pCapacitor_SMD:C_0603_1608MetricC10, C13
25k1Resistor_SMD:R_0603_1608MetricR7, R8
2LOGOLOGOG***, G***
2TPS7A8001DRBRPackage_DFN_QFN:Texas_DRB0008AU5, U6
112MCrystal:Crystal_SMD_3225-4Pin_3.2x2.5mmY1
115kResistor_SMD:R_0603_1608MetricR27
129.4912MHzOscillator:Oscillator_SMD_Abracon_ASV-4Pin_7.0x5.1mmX1
174AVC9112DCHPackage_SO:VSSOP-8_2.4x2.1mm_P0.5mmU1
174HC595DPackage_SO:SO-16_3.9x9.9mm_P1.27mmU2
1AT93C46D-TH-TPackage_SO:TSSOP-8_4.4x3mm_P0.65mmU3
1FT4232HLPackage_QFP:LQFP-64_10x10mm_P0.5mmU4
1USB_CConnector_USB:USB_C_Receptacle_GCT_USB4110J1
1WHTLED_SMD:LED_0603_1608MetricD9

The 198 most common of 200 parts.

Similar boards

  • 4 layers100 × 100 mmENGR357-receiverDesign, the printed circuit board in 3D

    ENGR357-receiverDesign

    jaronbrown/SDR_Receiver_Design

    The microPython module to control the SI5351, si5351.py, was provided by https://github.com/thaaraak/Tinypico-Radio/tree/master.

    132 parts1
  • 4 layers70 × 92.8 mmFE 8CH, the printed circuit board in 3D

    FE 8CH

    osqzss/PocketSDR

    The Pocket SDR FE device includes 2, 4, or 8 RF frontend channels, supporting the GNSS L1 band (1525 - 1610 MHz) or L2/L5/L6 bands (1160 - 1290 MHz). For these signal bands, refer to GNSS Signal Bands.

    238 parts17
  • 4 layers33.5 × 66.8 mmNet bmp, the printed circuit board in 3D

    Net bmp

    elagil/net-bmp

    An Ethernet-connected SWD/JTAG debug adapter (blackmagic probe)

    97 parts3GPL-3.0
  • 4 layers76 × 76.9 mmDsp amplifier x4, the printed circuit board in 3D

    Dsp amplifier x4

    blus-audio/hardware

    Audio hardware

    179 parts1CERN-OHL-S-2.0
  • 4 layers100 × 62 mmBreakout adc, the printed circuit board in 3D

    Breakout adc

    pbozeman/vanilla-ice40

    Hardware design and verilog sample files for Lattice ICE40 development boards and expansion boards.

    109 parts6MIT
  • 2 layers87.3 × 100 mmYuho, the printed circuit board in 3D

    Yuho

    shin-waseda/yuho-kicad_file

    138 parts
  • 2 layers100 × 40 mmSwitch board, the printed circuit board in 3D

    Switch board

    pavelpernicka/cvut_materialy

    71 parts
  • 2 layers100 × 102.6 mmDSP Regulator HAT RevB, the printed circuit board in 3D

    DSP Regulator HAT RevB

    Phil-CIA/Development-Station-Power-Supply

    3 channel bench supply with current and voltage plotting

    163 parts

Questions

How big is the Quad AMBE3000 PCB?

It measures 84 × 62 mm and has 4 copper layers, 1.6 mm thick.

What parts does the Quad AMBE3000 use?

200 parts, built around the 74AVC9112DCH, TPS7A8001DRBR, 74HC595D and AT93C46D-TH-T. The full list of its parts is on this page, with links to each part's symbol and footprint where PCBKit's library has them.

Where can I download the Quad AMBE3000 KiCad files?

From the m1geo/Quad-AMBE3000 repository on GitHub, at the commit this page was made from: the board is Quad-AMBE3000.kicad_pcb and its schematic Quad-AMBE3000.kicad_sch. PCBKit opens the board in the browser, with nothing to install.

Can I use the Quad AMBE3000 design in my own project?

Its repository publishes it under the MIT licence: you may reuse it on that licence's terms (keep the author's notice, and for a copyleft licence share your changes alike).