2 layers114 × 56.6 mm
ProbeBoardPublicV5
novintic/FlukeEmu-FluCom
HW/SW solution for Fluke 9010 mainframe emulation
76 parts27GPL-2.0
2 layers114 × 56.7 mm
FluCom5
novintic/FlukeEmu-FluCom27HW/SW solution for Fluke 9010 mainframe emulation
- Size
- 114 × 56.7 mm
- Copper layers
- 2
- Thickness
- 1.6 mm
- Parts
- 49
- Nets
- 73
- Pads
- 258
- Tracks, vias
- 608, 91
- Pours
- 2
- Routed
- Yes
- KiCad
- KiCad 8.0 (file 20240108)
- Created
- 9 Apr 2022
- Updated
- 16 Feb 2025
Overview
FluCom5 is an open-source printed circuit board by novintic, from the novintic/FlukeEmu-FluCom repository on GitHub, published under the GPL-2.0 licence. It is a 2-layer board of 114 × 56.7 mm with 49 parts on 73 nets, routed with 608 tracks and 91 vias.
It is built around the SN74LV1T34DBV, B0505S-1W and TXS0104EPW, with the BSS138 and B320 among its other parts. Its parts include 10 capacitors, 10 resistors, 10 connectors, 7 ICs and 5 diodes.
Main components
5
SN74LV1T34DBV
SOT-23-5-40℃~+125℃ 1 1 1.6V~5.5V 10uA 5.5ns@5V,15pF 74LV 8mA 8mA Level shifting Push-pull Unidirectional SOT-23-5 Buffers, Drivers, Receivers, Transceivers ROHSTexas InstrumentsBuffers, Drivers, Receivers, Transceivers
B0505S-1W
SIP-4-45℃~+85℃ 1 1.5kV 100uF 1W 200mA 23mA 4.5V~5.5V 5V 60mVp-p 77kHz 79% SIP-4 Isolated Power Modules ROHSEVISUNIsolated Power Modules
TXS0104EPW
TSSOP-14-40℃~+85℃ 1 1.65V~3.6V 2.3V~5.5V 24Mbps 4 Automatic direction detection、Output enable high-impedance、Integrated pull-up resistor Bidirectional Level translator Push-Pull、Open-drain TSSOP-14 Translators, Level Shifters ROHSTexas InstrumentsTranslators, Level Shifters
BSS138
SOT-23-55℃~+150℃ 1 N-channel 1.1Ω@10V、1.2Ω@4.5V 1.2V 1.7nC@10V 17.5pF 340mA 350mW 50V 6.5pF N-Channel SOT-23 MOSFETs ROHShongjiachengMOSFETs
B320
SMC(DO-214AB)-55℃~+150℃ 1 Independent 100A 100uA@20V 20V 3A 500mV@3A SMC(DO-214AB) Schottky Diodes ROHSDiodes IncorporatedSchottky Diodes
README
README.mdFlukeEmu-FluCom
A HW/SW solution for Fluke 9010 mainframe emulation
The Idea is to use a Raspberry Pi to run a Fluke 9010a emulator in software and interface with the hardware (pods) by means of an add on board/hat (basically to shift the levels and provide power to the pod). So far we have progressed from a proof of concept to a pretty solid and stable emulation.
The advantages of using an approach like this are many, amongst them:
- cheap Fluke 9010a mainframe replacement using modern technology and thereby adding stuff like network capability, wireless LAN, remote access/VNC, bluetooth etc ‚for free‘
- the interface board can supply all the power rails to the pod so only one 12V wall adapter is needed to power the RaspberryPi and the pods
- the whole setup is portable and compact, you could in theory put the whole thing inside your cabinet/UUT and comfortably use VNC to remote control the Fluke. You could also run the thing ‚headless‘ making it even smaller.
For further instruction on the fluCom board, please check: FlukeEmu-FluCom/fluCom/readme.md
For further instruction on the flukeEmuWx software, please check: FlukeEmu-FluCom/flukeEmuWx/readme.md
Credits
We would like to credit Adam Courchesne (@onecircuit) for coming up with the idea of a Fluke emulator and hardware combination and of course for being the first one to actually write one and make it available.
See also
Parts
49| Qty | Value | Footprint | References |
|---|---|---|---|
| 8 | 0.1uF | Capacitor_SMD:C_0805_2012Metric_Pad1.18x1.45mm_HandSolder | C1, C2, C3, C4, C5, C6, C9, C10 |
| 5 | 10K | Resistor_SMD:R_0805_2012Metric_Pad1.20x1.40mm_HandSolder | R2, R3, R4, R5, R14 |
| 4 | LED_Small | LED_SMD:LED_0805_2012Metric_Pad1.15x1.40mm_HandSolder | D2, D3, D4, D5 |
| 3 | 300R | Resistor_SMD:R_0805_2012Metric_Pad1.20x1.40mm_HandSolder | R10, R11, R13 |
| 3 | TXS0104EPW | Package_SO:SOIC-14_3.9x8.7mm_P1.27mm | U1, U2, U3 |
| 2 | BSS138 | Package_TO_SOT_SMD:SOT-23 | Q1, Q2 |
| 2 | Conn_01x02_Pin | Connector_PinHeader_2.54mm:PinHeader_1x02_P2.54mm_Vertical | J9, J10 |
| 2 | SN74LV1T34DBV | Package_TO_SOT_SMD:SOT-23-5 | U6, U7 |
| 1 | 10uF | Capacitor_SMD:C_0805_2012Metric_Pad1.18x1.45mm_HandSolder | C8 |
| 1 | 12V in | TerminalBlock:TerminalBlock_bornier-2_P5.08mm | J7 |
| 1 | 12V in Barrel Jack | Connector_BarrelJack:BarrelJack_Horizontal | J8 |
| 1 | 4.7uF | Capacitor_SMD:C_0805_2012Metric_Pad1.18x1.45mm_HandSolder | C7 |
| 1 | 700R | Resistor_SMD:R_0805_2012Metric_Pad1.20x1.40mm_HandSolder | R12 |
| 1 | B0505S | Converter_DCDC:Converter_DCDC_muRata_CRE1xxxxxxSC_THT | U5 |
| 1 | B320 | Diode_SMD:D_SMC | D1 |
| 1 | CK1408 | FluCom3:CK1408 | U4 |
| 1 | Conn_02x08_Top_Bottom | Connector_PinHeader_2.54mm:PinHeader_2x08_P2.54mm_Vertical | J3 |
| 1 | DB25_Female | Connector_Dsub:DSUB-25_Female_Horizontal_P2.77x2.54mm_EdgePinOffset9.40mm | J4 |
| 1 | Debug | Fluke6809POD:PinHeader_2x13_P2.54mm_Vertical_Fluke_Numbering_mirrored | J2 |
| 1 | Jumper_NC_Small | Connector_PinHeader_2.54mm:PinHeader_1x02_P2.54mm_Vertical | JP4 |
| 1 | OE | Connector_PinHeader_2.54mm:PinHeader_1x02_P2.54mm_Vertical | JP1 |
| 1 | Onboard -5V | Connector_PinHeader_2.54mm:PinHeader_1x02_P2.54mm_Vertical | JP3 |
| 1 | POWER | TerminalBlock:TerminalBlock_bornier-5_P5.08mm | J5 |
| 1 | PWset | Connector_PinHeader_2.54mm:PinHeader_2x04_P2.54mm_Vertical | J6 |
| 1 | R_Small | Resistor_SMD:R_0805_2012Metric_Pad1.20x1.40mm_HandSolder | R1 |
| 1 | Raspberry_Pi_2_3 | Connector_PinHeader_2.54mm:PinHeader_2x20_P2.54mm_Vertical | J1 |
| 1 | SW_Push | Button_Switch_SMD:SW_Push_1P1T_NO_CK_KMR2 | SW1 |
| 1 | TestPoint | Connector_PinHeader_2.54mm:PinHeader_1x01_P2.54mm_Vertical | TP1 |
More from novintic/FlukeEmu-FluCom
1Similar boards
- 4 layers56.5 × 65 mm
- 2 layers99.5 × 99.5 mm
ESP32 master
kwiecinski/BMS-and-offgrid-photovoltaic-management-system
Project contains BMS for lead-acid batteries and ESP-based board used to pull information from EASUN offgrid inverter, energy meters and sensors.
147 parts3MIT - 2 layers161.5 × 106 mm
WaccaProtocolTranslator
FizzyApple12/Waccon
A repository for all of the files in my design for an open-source touch ring controller.
108 parts33 - 2 layers103.1 × 125.6 mm
Esp32 usb hid 0805
adamwuqwq/esp32-macropad
A low budget macro numpad based on ESP32 and CH9329.
118 parts8MIT - 2 layers160 × 238.5 mm
- 2 layers100 × 80 mm
- 4 layers101.2 × 47.9 mm
Dashcam
Stevemwa/FMS_ESP32
This is a fleet management system that sends vehicle location data over to Firebase Cloud
129 parts - 2 layers33 × 74.9 mm
Smart penetrometer
ARTS-Laboratory/SPECIES
Design and development of a deployable UAV smart penetrometer
20 parts6CC-BY-SA-4.0
Questions
How big is the FluCom5 PCB?
It measures 114 × 56.7 mm and has 2 copper layers, 1.6 mm thick.
What parts does the FluCom5 use?
49 parts, built around the SN74LV1T34DBV, B0505S-1W, TXS0104EPW and BSS138. The full list of its parts is on this page, with links to each part's symbol and footprint where PCBKit's library has them.
Where can I download the FluCom5 KiCad files?
From the novintic/FlukeEmu-FluCom repository on GitHub, at the commit this page was made from: the board is FluCom/KiCAD8/FluCom5.kicad_pcb and its schematic FluCom/KiCAD8/FluCom5.kicad_sch. PCBKit opens the board in the browser, with nothing to install.
Can I use the FluCom5 design in my own project?
Its repository publishes it under the GPL-2.0 licence: you may reuse it on that licence's terms (keep the author's notice, and for a copyleft licence share your changes alike).