

Tv070hat
Raspberry Pi 5 HAT for Steam Deck LCD
- Size
- 56.5 × 65 mm
- Copper layers
- 4
- Thickness
- 1.61 mm
- Parts
- 54
- Nets
- 85
- Pads
- 299
- Tracks, vias
- 889, 182
- Pours
- 22
- Routed
- Yes
- KiCad
- KiCad 9.0 (file 20241229)
- Created
- 12 Aug 2026
- Updated
- 13 Aug 2026
Overview
Tv070hat is an open-source printed circuit board by ScandentLLC, from the ScandentLLC/tv070wxm-hat repository on GitHub, published under the CC0-1.0 licence. It is a 4-layer board of 56.5 × 65 mm with 54 parts on 85 nets, routed with 889 tracks and 182 vias.
It is built around the SN74LV1T34DBV, TPS92380PWP and TLV75718PDBV, with the TLV75733PDBV and TXS0104EPW among its other parts. Its parts include 18 capacitors, 14 resistors, 7 ICs, 3 connectors and 1 diode. It belongs with the lEDs and displays boards of this library.
Main components
5SN74LV1T34DBV
SOT-23-5-40℃~+125℃ 1 1 1.6V~5.5V 10uA 5.5ns@5V,15pF 74LV 8mA 8mA Level shifting Push-pull Unidirectional SOT-23-5 Buffers, Drivers, Receivers, Transceivers ROHSTexas InstrumentsBuffers, Drivers, Receivers, TransceiversTPS92380PWP
HTSSOP-20-40℃~+125℃ 0V~40V 120mA 3 300kHz~2.2MHz 4.5V~40V Built-in DC-DC PWM SEPIC、Boost HTSSOP-20 LED Drivers ROHSTexas InstrumentsLED DriversTLV75718PDBV
SOT-23-5-40℃~+125℃@(Tj) 1 1.8V 1A 40uA 45dB@(100kHz) 5.5V 71.5uVrms Fixed Positive Under Voltage Lockout、Over Current Protection、Over Temperature Protection、Soft Start、Enable SOT-23-5 Voltage Regulators - Linear, Low Drop Out (LDO) Regulators ROHSTexas InstrumentsVoltage Regulators - Linear, Low Drop Out (LDO) RegulatorsTLV75733PDBV
SOT-23-5-40℃~+125℃@(Tj) 1 1A 3.3V 40uA 46dB@(100kHz) 5.5V 650mV@(1A) 71.5uVrms Fixed Positive Under Voltage Lockout、Over Current Protection、Over Temperature Protection、Soft Start SOT-23-5 Voltage Regulators - Linear, Low Drop Out (LDO) Regulators ROHSTexas InstrumentsVoltage Regulators - Linear, Low Drop Out (LDO) RegulatorsTXS0104EPW
TSSOP-14-40℃~+85℃ 1 1.65V~3.6V 2.3V~5.5V 24Mbps 4 Automatic direction detection、Output enable high-impedance、Integrated pull-up resistor Bidirectional Level translator Push-Pull、Open-drain TSSOP-14 Translators, Level Shifters ROHSTexas InstrumentsTranslators, Level Shifters
README
README.mdTV070WXM-HAT
A Raspberry Pi 5 HAT form-factor adapter that connects the BOE TV070WXM-TV1-3GP1 MIPI-DSI LCD touch panel (the same display used in the LCD Steam Deck) to a Raspberry Pi 5.
![]() | ![]() |
| Front | Back |
Description
The TV070WXM-HAT breaks out a MIPI-DSI + touch interface so you can drive the BOE TV070WXM-TV1-3GP1 panel (the original Steam Deck LCD) directly from a Raspberry Pi 5. Two flat-flex cables carry DSI/touch between the Pi's DISP connector, the HAT, and the panel, and a 3D-printed bracket holds the whole stack together behind the display.
What's in this repo
- KiCad project — schematic (with full BOM), board layout, and Gerbers, ready to send to a fab.
- 3D-printable bracket — a simple STEP that sandwiches the Pi 5, HAT, and panel into one rigid assembly.
- Linux Kernel patch — a patch containing the driver and DTS files needed to make the display work on Linux.
Parts needed for assembly
[!WARNING] This HAT is only expected to work with the official Raspberry Pi 5 27 W (5.1 V / 5 A) USB-C power supply. Other power supplies will cause instability and brownouts unless they support 5 A current via USB-PD negotiation This is incredibly rare.
| Qty | Item | Digi-Key P/N | Notes |
|---|---|---|---|
| 1 | BOE TV070WXM-TV1-3GP1 panel | — | The Steam Deck LCD panel |
| 1 | Raspberry Pi 5 (with SD card) | — | |
| 1 | Raspberry Pi 5 official 27 W PSU | — | Required — see warning above |
| 1 | TV070WXM-HAT | — | This project — fab it from the included Gerbers |
| 1 | FFC, Pi 5 ↔ HAT | 2073-05-22-D-0030-A-4-06-4-T-ND | 22-pin, 0.5 mm, 30 mm, opposite-side contacts (GCT type D) |
| 1 | FFC, HAT ↔ display panel | WM9283-ND | Molex 0150150239 — 39-pin, 0.3 mm, 2" |
| 1 | 3D-printed bracket | — | STEP in this repo |
| 4 | 8mm M2.5X0.45 flat head screws | McMaster P/N 92010A018 | Source : McMaster Carr |
| 4 | 2.54 mm round nylon spacers | 492-1768-ND | Between bracket and Pi 5 |
| 4 | 11 mm M2.5×0.45 F/F standoffs | R25-1001102-ND | Between Pi 5 and HAT (See note about accommodating heatsink/cooler) |
| 4 | 8 mm M2.5×0.45 M/F standoffs | AE10794-ND | Above the HAT — the feet the assembly stands on |
Assembly
[!NOTE] This HAT is also compatible with the CM4 IO board, but it would require a much longer FFC between the DISP1 of the CM4 IO board and the J2 of the HAT to work. However, the hardware documentation focuses exclusively on the Raspberry Pi 5. The software documentation below includes instructions for the CM4.
Step 1 — Mount the Pi 5 to the bracket
Using the screws, the white plastic spacers, and the female-to-female standoffs, secure the Raspberry Pi 5 to the bracket. The stack order at each corner is: screw → spacer → Pi 5 → standoff.
![]() | ![]() |
Step 2 — Connect and mount the HAT
[!NOTE] To fit a Raspberry Pi 5 heatsink/active cooler between the Pi 5 and the HAT, you'll need a taller GPIO header extender and longer standoffs to clear the cooler's height. For the GPIO extender, consider Digikey P/N 1568-16763-ND, and for the longer standoffs (alternative to the 11mm standoffs), consider 25mm (Digikey P/N AE10862-ND) or 30mm (Digikey P/N 732-10626-ND)
Plug the small FFC ZIF cable into the CAM/DISP1 connector on the Pi 5, and plug the other end into the HAT. Seat the ZIF cable before mounting the HAT onto the 40-pin header — it's much easier that way. Then mount the HAT onto the Pi 5 and screw the male-female standoffs into the corners of the HAT. These are the legs the assembly stands on.
![]() | ![]() |
Step 3 — Connect the panel
Place the bracket on top of the display, then plug in the second FFC ZIF connector between the HAT and the display panel. Turn the assembly around and the hardware is ready.
Driver / software
The display will not light up on hardware alone — it needs a Linux kernel panel driver and matching device-tree overlays.
This repository includes the interim kernel patch:
linux-rpi-6.12.y-panel-boe-tv070wxm.patch
The long-term plan is to submit the driver to Linux mainline. Until that happens, apply the patch against the raspberrypi/linux tree's rpi-6.12.y branch.
Building the kernel
The patch was developed against the rpi-6.12.y branch (commit 5f23da14d91d4ba66604ec75453564e4e2afc57e) and applies cleanly to the tip of that branch as of commit f5a99b95354d38db209003a7d00560e5091ba94a.
-
Obtain the Raspberry Pi kernel sources for the
rpi-6.12.ybranch. -
Apply the patch:
bash git apply linux-rpi-6.12.y-panel-boe-tv070wxm.patch(or
patch -p1 < linux-rpi-6.12.y-panel-boe-tv070wxm.patch) -
Enable the driver in your kernel
.config:text CONFIG_DRM_PANEL_BOE_TV070WXM=m -
Build and install the kernel the same way you normally build a custom Raspberry Pi kernel. See the official Raspberry Pi documentation if necessary.
Once the driver is accepted upstream you can simply use a Raspberry Pi or mainline kernel that already contains it.
[!TIP] If using a custom kernel before the driver is accepted upstream, use an alternative kernel name such as
kernel_2712-custom.imgand edit config.txt to specifykernel=kernel_2712-custom.img. Without this, system updates will replace the kernel, causing black screens on reboot from the lack of a driver. Also, you will likely want to regenerate a corresponding initramfs using update-initramfs.
Device-tree overlays (config.txt)
[!NOTE] Unlike official HAT/HAT+ accessories, this does not include an ID EEPROM for auto-loaded overlays.
Raspberry Pi 5 (and CM5)
Add the following lines to /boot/firmware/config.txt:
display_auto_detect=0
dtoverlay=vc4-kms-v3d-pi5
dtoverlay=boe-tv070wxm-pi5The Raspberry Pi 5 instructions are expected to work on the CM5 as well, but it is untested.
Compute Module 4
Add the following lines to /boot/firmware/config.txt:
display_auto_detect=0
dtoverlay=vc4-kms-v3d
dtoverlay=boe-tv070wxmX11 configuration (rotation & touch)
[!NOTE] Only X11 is tested. Current Raspberry Pi OS defaults to Wayland. Switch to X11 in raspi-config (Advanced Options → Wayland) before using the config below.
On the Steam Deck, screen rotation is handled by drm_panel_orientation_quirks.c using DMI data that does not exist on the Raspberry Pi, and touch-input rotation is performed in userspace. Consequently an X11 configuration file is required (unless you prefer the display's native portrait orientation). The Linux kernel obtains a landscape orientation from the DTS for the kernel console, but nothing else uses that.
Raspberry Pi 5 (and CM5)
Install the following file:
cat << 'END' | sudo tee /usr/share/X11/xorg.conf.d/95-touch-rotate.conf
Section "Monitor"
Identifier "DSI-2"
Option "Rotate" "left"
EndSection
Section "InputClass"
Identifier "Steam Deck Touchscreen"
MatchProduct "hid-over-i2c 2808:1015"
MatchIsTouchscreen "on"
Option "TransformationMatrix" "0 -1 1 1 0 0 0 0 1"
EndSection
ENDThis is expected to work on the CM5 as well, but it is untested.
After a reboot the panel should display text in a landscape orientation with a working touchscreen.
Compute Module 4
Install the following file:
cat << 'END' | sudo tee /usr/share/X11/xorg.conf.d/95-touch-rotate.conf
Section "Monitor"
Identifier "DSI-1"
Option "Rotate" "left"
EndSection
Section "InputClass"
Identifier "Steam Deck Touchscreen"
MatchProduct "hid-over-i2c 2808:1015"
MatchIsTouchscreen "on"
Option "TransformationMatrix" "0 -1 1 1 0 0 0 0 1"
EndSection
ENDAfter a reboot the panel should display text in a landscape orientation with a working touchscreen.
Purpose
We originally developed this for our own internal use at Scandent LLC. The first iteration was an adapter board for the CM4 IO that we created as a development artifact that allowed us to bring up the Steam Deck LCD on the CM4 without investing into a full custom CM4 carrier board spin before we knew whether it would work.
We love open source and wish to share what we can with others for their reuse. Thus, after we confirmed that this worked, we redesigned our adapter board into a HAT form factor. It is our hope that others will find what we have done useful and incorporate it into their own projects. This includes the creation of commercial versions. For that reason, we have selected the CC0-1.0 license for our hardware, to ensure that there are no barriers to third party use.
For those who do incorporate this into their own CM4/CM5 carrier boards, note that very careful attention must be given to the MIPI DSI lane lengths and signal integrity.
License
Unless otherwise specified, files in this repository are licensed under the CC0-1.0 license. See LICENSE.
The linux kernel patch is the primary (and at the time of writing, the only) exception. It is licensed under the GPLv2.
Credits
- Hardware engineering / documentation — Akshay Athalye
- Software engineering / documentation — Richard Yao
- HAT Evaluation / Comments — Jeff Geerling
Parts
54| Qty | Value | Footprint | References |
|---|---|---|---|
| 5 | 0 | Resistor_SMD:R_0402_1005Metric | R8, R9, R10, R11, R13 |
| 4 | 10k | Resistor_SMD:R_0603_1608Metric | R2, R4, R12, R14 |
| 3 | 10u | Capacitor_SMD:C_0805_2012Metric | C5, C6, C8 |
| 3 | 10u | Capacitor_SMD:C_1206_3216Metric | C9, C10, C11 |
| 3 | 1u | Capacitor_SMD:C_0603_1608Metric | C1, C2, C7 |
| 2 | 0.1u | Capacitor_SMD:C_0603_1608Metric | C15, C16 |
| 2 | 0.1u | Capacitor_SMD:C_0402_1005Metric | C13, C14 |
| 2 | 0.47u | Capacitor_SMD:C_0603_1608Metric | C3, C4 |
| 2 | 1u | Capacitor_SMD:C_0402_1005Metric | C17, C18 |
| 2 | Gnd | TestPoint:TestPoint_Pad_1.0x1.0mm | TP3, TP4 |
| 2 | SN74LV1T34DBV | Package_TO_SOT_SMD:SOT-23-5 | U4, U6 |
| 1 | 0 | Resistor_SMD:R_0603_1608Metric | R1 |
| 1 | 100V, 1A | Diode_SMD:D_SMA | D1 |
| 1 | 100k | Resistor_SMD:R_0603_1608Metric | R7 |
| 1 | 10n | Capacitor_SMD:C_0402_1005Metric | C12 |
| 1 | 10u | tvo70-hat:L_BMRF00060630 | L1 |
| 1 | 120k | Resistor_SMD:R_0603_1608Metric | R5 |
| 1 | 22Pos FFC(0.5mm) | tvo70-hat:Hirose_FH12-22S-0.5SH_1x22-1MP_P0.50mm_Horizontal | J2 |
| 1 | 39 POS FFC(0.3mm) | tvo70-hat:Hirose-FH26W-39S-0.3SHW(60)-Flipped | J3 |
| 1 | 42.2k | Resistor_SMD:R_0603_1608Metric | R3 |
| 1 | 562k | Resistor_SMD:R_0603_1608Metric | R6 |
| 1 | 5V | TestPoint:TestPoint_Pad_1.0x1.0mm | TP1 |
| 1 | DRst | TestPoint:TestPoint_Pad_1.0x1.0mm | TP7 |
| 1 | FLT | TestPoint:TestPoint_Pad_1.0x1.0mm | TP9 |
| 1 | HAT_Outline | tvo70-hat:TV070_HAT+ | U7 |
| 1 | NetTie_2 | NetTie:NetTie-2_SMD_Pad2.0mm | NT1 |
| 1 | PWM | TestPoint:TestPoint_Pad_1.0x1.0mm | TP2 |
| 1 | Raspberry_Pi_GPIO | Connector_PinSocket_2.54mm:PinSocket_2x20_P2.54mm_Vertical | J5 |
| 1 | TInt | TestPoint:TestPoint_Pad_1.0x1.0mm | TP6 |
| 1 | TLV75718PDBV | Package_TO_SOT_SMD:SOT-23-5 | U2 |
| 1 | TLV75733PDBV | Package_TO_SOT_SMD:SOT-23-5 | U1 |
| 1 | TPS92380 | tvo70-hat:PWP0020A-IPC_C | U3 |
| 1 | TRst | TestPoint:TestPoint_Pad_1.0x1.0mm | TP5 |
| 1 | TXS0104EPW | Package_SO:TSSOP-14_4.4x5mm_P0.65mm | U5 |
| 1 | Vled | TestPoint:TestPoint_Pad_1.0x1.0mm | TP8 |
Similar boards
- 4 layers100 × 100 mm

- 6 layers100 × 75 mm

STM32H743
sneakylizard123-4/STM32H743
This board puts an STM32H743XIH6 and an iCE40 UP5K on the same PCB. The H743 handles control, USB, Ethernet, storage, and audio.
171 partsCERN-OHL-P-2.0 - 2 layers114 × 56.7 mm

- 2 layers23.5 × 34 mm

Mouse
AzumahJr7/Wireless-Mouse
This projects contains files for creating your own wireless mouse. Software applications that would be used are SolidWorks and KiCad
17 parts1 - 4 layers50 × 37.5 mm

- 2 layers66 × 33 mm

- 2 layers137 × 105 mm

Lijnsensor
Stan-debakker/grap-6TWEA
Daarnaast moest ik ervoor zorgen dat de nieuwe sensoren correct werken. Ik ben gestart met experimenteren via Arduino IDE, zie "codearduinoIDE".
30 parts - 4 layers219 × 108.5 mm

Z80DevBoard
gianluca-rainis/Z80DevBoard
An advanced development board for the Z80 microprocessor, powered by an RP2040.
182 parts7CERN-OHL-S-2.0
Questions
How big is the Tv070hat PCB?
It measures 56.5 × 65 mm and has 4 copper layers, 1.61 mm thick.
What parts does the Tv070hat use?
54 parts, built around the SN74LV1T34DBV, TPS92380PWP, TLV75718PDBV and TLV75733PDBV. The full list of its parts is on this page, with links to each part's symbol and footprint where PCBKit's library has them.
Where can I download the Tv070hat KiCad files?
From the ScandentLLC/tv070wxm-hat repository on GitHub, at the commit this page was made from: the board is tv070hat.kicad_pcb and its schematic mipi-lanes.kicad_sch. PCBKit opens the board in the browser, with nothing to install.
Can I use the Tv070hat design in my own project?
Its repository publishes it under the CC0-1.0 licence: you may reuse it on that licence's terms (keep the author's notice, and for a copyleft licence share your changes alike).





