
Pcbcard
haohaohaoyan/pcb-badge
An RP2350A devboard and NFC card in the exact same footprint as my county's school-mandated ID badges. This was supposed to work with them but I suspect the cards are actually low-frequency and those are harder to…

This is a custom PCB badge that you can change the details of through to be displayed on an e-ink display. It also has a customizable NFC tag
Custom PCB Badge is an open-source printed circuit board by nilaynagh8-del, from the nilaynagh8-del/Customizable-PCB-Badge repository on GitHub, published under the MIT licence. It is a 6-layer board of 113.7 × 61.3 mm with 110 parts on 148 nets, routed with 2,088 tracks and 257 vias.
It is built around the RP2040, W25Q128JVSIQ and ST25DV04K-IER8C3, with the SK6812MINI-E among its other parts. Its parts include 56 diodes, 21 capacitors, 10 resistors, 5 connectors and 4 ICs. It belongs with the lEDs and displays boards and the RP2040 boards of this library.
A customizable PCB badge with built in NFC & games!
| Mode (long-press SW4 to cycle) | What happens |
|---|---|
| 1. Flappy | Flappy-bird on the LED grid. SW3 = flap, SW4 = restart. Speeds up as you score. |
| 2. Pong | 2-player pong, first to 5. SW3 = left paddle, SW4 = right paddle. |
| 3. NFC | Pick one of 3 payloads with SW3 (URL / text / vCard), write it to the ST25DV tag with SW4. Green frame = tag present, red = not detected. Green sweep = write verified OK. |
| 4. Demo | Rainbow across the whole grid. |
SW2 toggles the 6 THT LEDs at any time, in any mode – it's wired straight to GPIO13.
The NFC tag behaves like a normal Type-5 NDEF tag: after a write, tapping it to a phone opens the URL, shows the text, or offers the contact card.
Customizing the NFC payloads
Edit the three strings near the top of badge-firmware.ino:
static const char *NFC_PAYLOAD_URL = "https://hackclub.com";
static const char *NFC_PAYLOAD_TEXT = "Hello to whoever taps this badge!";
static const char *NFC_PAYLOAD_VCARD = "BEGIN:VCARD\nVERSION:3.0\nFN:YOUR NAME...";URI prefixes are auto-detected (https://, http://www., tel:, mailto: …)
and encoded compactly per the NDEF spec. Writes are verified by read-back; the
password session re-opens between attempts if the first write fails. Firmware
size per payload is capped at 254 bytes (TLV short form) but the payload
themselves are clamped to 200 bytes each — plenty for a URL, a message, and a
contact card on the 512-byte ST25DV04K.
the PCB is pretty compact and tightly packed together with many components, which forced me to make this PCB 6 layers. I used 2 GND planes, one on the top layer and another on the bottom. For the NFC antenna I used a plugin to generate me one with copper wire routing to make it part of the PCB itself so it doesn't require an external antenna. here are some photos of the design below.
Main MCU Components
LEDs and buttons for games
E-ink Display
NFC tag components
LED for fun lighting on the front
Final PCB Design
PCB front and back
The software of this device is pretty simple all you have to do is hold the BOOTSEL button on the board and drop the the Badge-firmware.ino.uf2 onto the device. You will then be able to upload you're ID and play games etc.
| #Part | #Price |
|---|---|
| 1x rp2040 | $0.76 |
| 1x W25Q128JVS | $5.99 |
| 1x USB-C 2.0 receptacle | $0.74 |
| 50x SK6812MINI LEDS | $11.98 |
| 1x ST25DV04K-IER8C3 | $1.10 |
| 6x 5mm THT LED | $3.30 |
| 3x PTS645Sx43SMTR92 Switches | $1.08 |
| 1x KMR2 switch | $0.67 |
| 14x 0402 0.1uf capacitors | $1.40 |
| 3x 0603 10uf capacitors | $0.63 |
| 4x 0402 15pf capacitors | $0.52 |
| 1x NCP1117ST33T3G | $0.65 |
| 2x 5.1k 0402 resistors | $0.20 |
| 2x 27 ohm 0402 resistors | $0.20 |
| 2x 1k 0402 resistors | $0.20 |
| 1x 10k 0402 resistors | $0.11 |
| 2x 4.7k 0402 resistors | $0.10 |
| 1x 470 ohm 0402 resistors | $0.11 |
| 1x E-ink Display | $23.03 |
| Total Price of Parts (excluding PCB) | $52.77 |
This project is open source. If anything you make out of this does not work or has any issues, I sincerely apologize, but at the end of the day that's on you. Big shout out to Hack Club for giving me the opportunity to make this project. I would also like to thank Kai Pereira, as my project is heavily inspired his PCB badge in many ways.
| Qty | Value | Footprint | References |
|---|---|---|---|
| 50 | SK6812MINI | LED_SMD:LED_SK6812MINI_PLCC4_3.5x3.5mm_P1.75mm | D49, D50, D51, D52, D53, D54, D55, D56, D57, D58, D59, D60, D61, D62, D63, D64 +34 |
| 13 | 0.1uf | Capacitor_SMD:C_0402_1005Metric_Pad0.74x0.62mm_HandSolder | C1, C2, C3, C4, C5, C6, C7, C8, C9, C10, C11, C12, C17 |
| 8 | LOGO | LOGO | , , , , , , G***, G*** |
| 6 | LED | LED_THT:LED_D5.0mm | D1, D2, D3, D4, D9, D10 |
| 4 | 15pf | Capacitor_SMD:C_0402_1005Metric_Pad0.74x0.62mm_HandSolder | C15, C16, C19, C20 |
| 3 | 10uf | Capacitor_SMD:C_0603_1608Metric_Pad1.08x0.95mm_HandSolder | C13, C14, C18 |
| 3 | SW_Push | Button_Switch_SMD:SW_SPST_PTS645Sx43SMTR92 | SW2, SW3, SW4 |
| 2 | 1k | Resistor_SMD:R_0402_1005Metric_Pad0.72x0.64mm_HandSolder | R5, R6 |
| 2 | 27 | Resistor_SMD:R_0402_1005Metric_Pad0.72x0.64mm_HandSolder | R3, R4 |
| 2 | 4.7k | Resistor_SMD:R_0402_1005Metric_Pad0.72x0.64mm_HandSolder | R8, R9 |
| 1 | 100nf | Capacitor_SMD:C_0402_1005Metric_Pad0.74x0.62mm_HandSolder | C21 |
| 1 | 10k | Resistor_SMD:R_0402_1005Metric_Pad0.72x0.64mm_HandSolder | R7 |
| 1 | 12mhz | Crystal:Crystal_SMD_3225-4Pin_3.2x2.5mm_HandSoldering | Y1 |
| 1 | 5.1K | Resistor_SMD:R_0402_1005Metric_Pad0.72x0.64mm_HandSolder | R1 |
| 1 | 5.1k | Resistor_SMD:R_0402_1005Metric_Pad0.72x0.64mm_HandSolder | R2 |
| 1 | 70 | Resistor_SMD:R_0402_1005Metric_Pad0.72x0.64mm_HandSolder | R10 |
| 1 | Antenna_Loop | Connector_PinHeader_2.54mm:PinHeader_1x02_P2.54mm_Vertical_SMD_Pin1Left | AE1 |
| 1 | Conn_01x08 | Connector_PinHeader_2.54mm:PinHeader_1x08_P2.54mm_Vertical | J5 |
| 1 | Conn_01x11_MountingPin | Connector_PinHeader_2.54mm:PinHeader_1x11_P2.54mm_Vertical | J8 |
| 1 | Conn_01x15_MountingPin | Connector_PinHeader_2.54mm:PinHeader_1x15_P2.54mm_Vertical | J3 |
| 1 | Conn_02x20_Odd_Even | Connector_PinHeader_2.54mm:PinHeader_2x20_P2.54mm_Vertical | J2 |
| 1 | NCP1117-3.3_SOT223 | Package_TO_SOT_SMD:SOT-223-3_TabPin2 | U2 |
| 1 | RP2040 | Package_DFN_QFN:QFN-56-1EP_7x7mm_P0.4mm_EP3.2x3.2mm | U1 |
| 1 | ST25DV04K-IER8C3 | Package_DFN_QFN:DFN-8-1EP_3x2mm_P0.5mm_EP1.36x1.46mm | U4 |
| 1 | SW_Push | Button_Switch_SMD:SW_Push_1P1T_NO_CK_KMR2 | SW1 |
| 1 | USB_C_Receptacle_USB2.0_14P | Connector_USB:USB_C_Receptacle_HRO_TYPE-C-31-M-12 | J1 |
| 1 | W25Q128JVS | Package_SO:SOIC-8_5.3x5.3mm_P1.27mm | U3 |

haohaohaoyan/pcb-badge
An RP2350A devboard and NFC card in the exact same footprint as my county's school-mandated ID badges. This was supposed to work with them but I suspect the cards are actually low-frequency and those are harder to…

PowerPlane/insert-coin
The "Insert Coin" cards are PCB-as-business-card builds where the coin cell is the user interaction: slide it into the holder and the card boots, blinks, listens, taps NFC, then sleeps.

frewden/F1-NFC-Powered-PCB
Batteryless Formula 1-inspired NFC PCB with energy harvesting, ATtiny1616 and charlieplexed LED lighting, designed in KiCad.


SANJEEV306/pcb_business_card
A NFC business card with ST25DV NFC/RFID tag IC. ST25DV works with 13.5 MHz spiral coil in 2.54 mm thickness 2 layer PCB board.

wrickert/NFCBusiness
Using NFC to create a PCB business card that does not need a battery

Bastardkb/Dilemma
The Dilemma is a vertical stagger low-profile keyboard with mods.

weteor/Qazikat
qaz-like keyboard with offset space, arrow cluster and ISO-enter
It measures 113.7 × 61.3 mm and has 6 copper layers, 1.6 mm thick.
110 parts, built around the RP2040, W25Q128JVSIQ, ST25DV04K-IER8C3 and SK6812MINI-E. The full list of its parts is on this page, with links to each part's symbol and footprint where PCBKit's library has them.
From the nilaynagh8-del/Customizable-PCB-Badge repository on GitHub, at the commit this page was made from: the board is PCB/Custom PCB Badge.kicad_pcb and its schematic PCB/Custom PCB Badge.kicad_sch. PCBKit opens the board in the browser, with nothing to install.
Its repository publishes it under the MIT licence: you may reuse it on that licence's terms (keep the author's notice, and for a copyleft licence share your changes alike).