2 layers79 × 38 mm
Ethersweep
Neumi/ethersweep
Open Source, easy to use Ethernet connected stepper motor controller. Built in FreeCAD, KiCAD and Arduino.
111 parts587
4 layers79 × 38 mm
Ethersweep
Neumi/ethersweep587Open Source, easy to use Ethernet connected stepper motor controller. Built in FreeCAD, KiCAD and Arduino.
- Size
- 79 × 38 mm
- Copper layers
- 4
- Thickness
- 1.6 mm
- Parts
- 111
- Nets
- 124
- Pads
- 488
- Tracks, vias
- 1,174, 149
- Pours
- 4
- Routed
- Yes
- KiCad
- KiCad 7 (file 20221018)
- Created
- 19 Mar 2020
- Updated
- 23 Apr 2025
Overview
Ethersweep is an open-source printed circuit board by Neumi, from the Neumi/ethersweep repository on GitHub. It is a 4-layer board of 79 × 38 mm with 111 parts on 124 nets, routed with 1,174 tracks and 149 vias.
It is built around the CP2102N-A01-GQFN28R, TMC2209-LA and W5500, with the R1M and HR911105A among its other parts. Its parts include 39 capacitors, 30 resistors, 11 connectors, 6 ICs and 6 diodes. It belongs with the robots and motor control and interfaces and adapters boards and the STM32 boards of this library.
Main components
5
CP2102N-A01-GQFN28R
QFN-28-EP(5x5)-40℃~+85℃ 13.7mA 195uA 3Mbps 3V~3.6V Transceiver USB 2.0 QFN-28-EP(5x5) USB Converters ROHSSilicon LabsUSB Converters
TMC2209-LA
QFN-28-EP_5x5QFN-28-EP(5x5) SMT ROHSAnalog DevicesUncategorised
W5500
LQFP-48_7x7-40℃~+85℃ 10BASE-T、100BASE-TX 3.3V 32KB SPI SPI Wake-up function、Programmable LED indication、Low-power mode Yes LQFP-48(7x7) Ethernet Controllers ROHSWIZNETEthernet Controllers
R1M
SOD-123FL-55℃~+150℃ 1 Independent 1.3V@1A 1A 1kV 500ns 5uA SOD-123FL Fast Recovery / High Efficiency Diodes ROHSMDMFast Recovery / High Efficiency Diodes
HR911105A
插件0℃~+70℃ 1 Filtered Gold Non-PoE Phosphor bronze RJ45 Jack Right Angle Shielded With LED 插件 Ethernet Connectors / Modular Connectors (RJ45 RJ11) ROHSHANRUNEthernet Connectors / Modular Connectors (RJ45 RJ11)
README
electronic_design/development/ethersweep407_CAN/readme.mdVersion 4.6.0
Current development files.
Parts
111| Qty | Value | Footprint | References |
|---|---|---|---|
| 15 | C100nF | Capacitor_SMD:C_0402_1005Metric | C12, C14, C15, C16, C17, C18, C19, C20, C21, C22, C29, C32, C37, C41, C42 |
| 8 | MountingHole_Pad | MountingHole:MountingHole_3.2mm_M3_Pad_Via | H1, H2, H3, H4, H5, H6, H7, H8 |
| 6 | R10k | Resistor_SMD:R_0402_1005Metric | R3, R16, R24, R27, R28, R29 |
| 5 | C100nF | Capacitor_SMD:C_0603_1608Metric | C1, C6, C23, C27, C38 |
| 5 | R330 | Resistor_SMD:R_0603_1608Metric | R13, R19, R20, R25, R26 |
| 4 | LED | LED_SMD:LED_0603_1608Metric | D1, D2, D3, D4 |
| 4 | R33 | Resistor_SMD:R_0603_1608Metric | R4, R5, R6, R7 |
| 4 | R49.9 | Resistor_SMD:R_0603_1608Metric | R9, R10, R18, R23 |
| 2 | AVR-ISP-6 | Connector_IDC:IDC-Header_2x03_P2.54mm_Vertical | J1, J8 |
| 2 | C10uF | Capacitor_SMD:C_1206_3216Metric | C31, C40 |
| 2 | C10uF | Capacitor_SMD:C_0805_2012Metric | C26, C30 |
| 2 | C18pF | Capacitor_SMD:C_0402_1005Metric | C33, C34 |
| 2 | C22pF | Capacitor_SMD:C_0402_1005Metric | C8, C10 |
| 2 | C6.8nF | Capacitor_SMD:C_0402_1005Metric | C7, C13 |
| 2 | Conn_01x03_Male | Connector_JST:JST_EH_S3B-EH_1x03_P2.50mm_Horizontal | J4, J5 |
| 2 | R100mOHM | Resistor_SMD:R_2010_5025Metric | R11, R12 |
| 2 | R10k | Resistor_SMD:R_0603_1608Metric | R1, R2 |
| 2 | R1M | Resistor_SMD:R_0402_1005Metric | R14, R21 |
| 2 | R1k | Resistor_SMD:R_0402_1005Metric | R17, R30 |
| 1 | 3.3V | TestPoint:TestPoint_Pad_D2.0mm | TP1 |
| 1 | AS5600 | modules:AS5600 | U5 |
| 1 | BOOT_0 | TestPoint:TestPoint_Pad_D2.0mm | TP6 |
| 1 | BOOT_1 | TestPoint:TestPoint_Pad_D2.0mm | TP5 |
| 1 | C10nF | Capacitor_SMD:C_0603_1608Metric | C5 |
| 1 | C10nF | Capacitor_SMD:C_0402_1005Metric | C35 |
| 1 | C1nF | Capacitor_SMD:C_1206_3216Metric | C3 |
| 1 | C2.2-4.7uF ceramic | Capacitor_SMD:C_1206_3216Metric | C11 |
| 1 | C22nF | Capacitor_SMD:C_0603_1608Metric | C4 |
| 1 | C22nF 50V | Capacitor_SMD:C_0402_1005Metric | C9 |
| 1 | C4.7uF | Capacitor_SMD:C_0402_1005Metric | C36 |
| 1 | C4.7uF | Capacitor_SMD:C_1206_3216Metric | C2 |
| 1 | CP2102N-A01-GQFN28 | Package_DFN_QFN:QFN-28-1EP_5x5mm_P0.5mm_EP3.35x3.35mm | U2 |
| 1 | C_330uF | Capacitor_SMD:CP_Elec_10x10 | C39 |
| 1 | Conn_01x02_Male | Connector_AMASS:AMASS_XT30PW-M_1x02_P2.50mm_Horizontal | J2 |
| 1 | Conn_01x04_Female | Connector_JST:JST_EH_S4B-EH_1x04_P2.50mm_Horizontal | J9 |
| 1 | Conn_01x04_Female | Connector_PinHeader_2.54mm:PinHeader_1x04_P2.54mm_Vertical | J3 |
| 1 | Conn_01x07_Female | Connector_PinHeader_2.54mm:PinHeader_1x07_P2.54mm_Vertical | J6 |
| 1 | Conn_01x07_Male | Connector_PinHeader_2.54mm:PinHeader_1x07_P2.54mm_Vertical | J7 |
| 1 | Crystal | Crystal:Crystal_SMD_5032-2Pin_5.0x3.2mm | Y3 |
| 1 | Crystal_25MHz | Crystal:Crystal_SMD_3225-4Pin_3.2x2.5mm | Y2 |
| 1 | DD4012SA | modules:DD4012SA | U4 |
| 1 | D_TVS_30V | Diode_SMD:D_SOD-123 | D6 |
| 1 | D_TVS_5V | Diode_SMD:D_SOD-123 | D5 |
| 1 | GND | TestPoint:TestPoint_Pad_D2.0mm | TP2 |
| 1 | HR911105A | modules:HANRUN_HR911105A | J10 |
| 1 | L600OHM | Inductor_SMD:L_0805_2012Metric | L1 |
| 1 | R10 | Resistor_SMD:R_0603_1608Metric | R8 |
| 1 | R12K4 | Resistor_SMD:R_0603_1608Metric | R22 |
| 1 | R1k | Resistor_SMD:R_0603_1608Metric | R15 |
| 1 | RX | TestPoint:TestPoint_Pad_D2.0mm | TP3 |
| 1 | STM32F103C8Tx | Package_QFP:LQFP-48_7x7mm_P0.5mm | U3 |
| 1 | SW_BOOT_0 | Button_Switch_SMD:SW_SPST_B3U-3000P | SW2 |
| 1 | SW_Push | Button_Switch_SMD:SW_SPST_B3U-3000P | SW1 |
| 1 | TMC2209-LA | KiCad:TMC2209-LA | U7 |
| 1 | TX | TestPoint:TestPoint_Pad_D2.0mm | TP4 |
| 1 | USB_B_Micro | Connector_USB:USB_Micro-AB_Molex_47590-0001 | J11 |
| 1 | W5500 | Package_QFP:LQFP-48_7x7mm_P0.5mm | U6 |
More from Neumi/ethersweep
3- 4 layers79 × 38 mm
Ethersweep
Neumi/ethersweep
Open Source, easy to use Ethernet connected stepper motor controller. Built in FreeCAD, KiCAD and Arduino.
110 parts587 - 4 layers38 × 38 mm
Ethersweep
Neumi/ethersweep
Open Source, easy to use Ethernet connected stepper motor controller. Built in FreeCAD, KiCAD and Arduino.
24 parts587
Similar boards
- 2 layers123 × 87.5 mm
FastLOGIC
Neumi/fastLOGIC
An affordable Arduino-based board designed for straightforward (industrial) logic control, ideal for building small-scale automation and control solutions.
180 parts23MIT - 2 layers89.9 × 64 mm
- 2 layers
TUSS4470 shield
Neumi/open_echo
Open Source echo sounder / depth sounder / SONAR for bathymetry and research. Arduino based and compatible.
51 parts530 - 4 layers42 × 42 mm
- 4 layers72.6 × 170 mm
OpenJBOD RP2040
OpenJBOD/rp2040
This repository contains the hardware design files OpenJBOD RP2040 Baseboard.
129 parts87CERN-OHL-P-2.0 - 4 layers83.2 × 15.7 mm
- 4 layers44.3 × 95.9 mm
- 2 layers200 × 170 mm
Routing R1
ddasdkimo/rack-atx-controller
10-host isolated ATX rack controller hardware planning, interactive 3D model and wiring documentation
698 parts
Questions
How big is the Ethersweep PCB?
It measures 79 × 38 mm and has 4 copper layers, 1.6 mm thick.
What parts does the Ethersweep use?
111 parts, built around the CP2102N-A01-GQFN28R, TMC2209-LA, W5500 and R1M. The full list of its parts is on this page, with links to each part's symbol and footprint where PCBKit's library has them.
Where can I download the Ethersweep KiCad files?
From the Neumi/ethersweep repository on GitHub, at the commit this page was made from: the board is electronic_design/development/ethersweep406/ethersweep.kicad_pcb and its schematic electronic_design/development/ethersweep402/ethersweep.kicad_sch. PCBKit opens the board in the browser, with nothing to install.
Can I use the Ethersweep design in my own project?
Its repository states no licence, so its author keeps all rights: ask Neumi before reusing the design.