Skip to the content
2 layers46.2 × 31 mmBoard v09, the printed circuit board in 3D

High-voltage power and trigger stage for a microcontroller-controlled capacitor discharge ignition (CDI) system, intended for small engines.

Size
46.2 × 31 mm
Copper layers
2
Thickness
1.6 mm
Parts
37
Nets
23
Pads
79
Tracks, vias
156, 8
Routed
Yes
KiCad
KiCad 7 (file 20221018)
Created
20 Oct 2026
Updated
21 Oct 2026

Overview

Board v09 is an open-source printed circuit board by nelsonyamamoto, from the nelsonyamamoto/uC-CDI repository on GitHub. It is a 2-layer board of 46.2 × 31 mm with 37 parts on 23 nets, routed with 156 tracks and 8 vias.

It is built around the LM2577T-ADJ, 2N7002K and UF4007. Its parts include 10 resistors, 10 diodes, 6 capacitors, 2 transistors and 1 IC.

Main components

3

README

README.md

uC-CDI

High-voltage power and trigger stage for a microcontroller-controlled capacitor discharge ignition (CDI) system, intended for small engines. An external MCU controls the charge enable and spark timing; this board generates the high voltage, stores the discharge energy, and fires the ignition coil. Board revision: v0.9.

Hardware

Charging stage

  • LM2577T-ADJ switching regulator (U1) configured as a flyback/boost converter, driving custom transformer T1 (22 T / 330 T / 21 T windings on an E20 core) to generate the high-voltage rail
  • UF4007 fast-recovery rectifiers (D2, D6, D7) in the HV path
  • 1.5 µF discharge/storage capacitor (C4)
  • Charge-voltage regulation through zener feedback into the LM2577 FB pin (D2/D4 network), with 120 V (D10), 200 V (D9) and 24 V (D4) zener clamps

Discharge / trigger stage

  • TIC116 SCR (Q3) dumps the storage capacitor into the ignition coil
  • Isolated gate drive through pulse transformer T2 (1P:1S)
  • 2N7002K small-signal MOSFET (Q2) in the trigger path, driven by the external MCU timing signal
  • Separate grounds (GND / GND1) isolating the control side from the ignition side

Interface

External connections (power in, trigger in, HV output to the coil, grounds) are broken out on through-hole test-point pads TP1–TP6.

Repository contents

FileDescription
board-v09.kicad_proKiCad 7 project file
board-v09.kicad_schSchematic
board-v09.kicad_pcbPCB layout (mixed SMD/THT)

Requirements

  • KiCad 7 or later

Warning

This board generates and stores several hundred volts. The 1.5 µF discharge capacitor can hold a lethal charge after power is removed — verify it is fully discharged before handling.

Status

Work in progress — schematic and PCB layout exist (v0.9). No firmware in this repository.

License

No license file is currently included; the design files are provided as-is.

Parts

37
QtyValueFootprintReferences
6TestPointTestPoint:TestPoint_THTPad_2.5x2.5mm_Drill1.2mmTP1, TP2, TP3, TP4, TP5, TP6
41N4148Diode_SMD:D_MiniMELFD1, D3, D5, D8
310kResistor_SMD:R_0805_2012Metric_Pad1.20x1.40mm_HandSolderR3, R6, R9
22K2Resistor_SMD:R_0805_2012Metric_Pad1.20x1.40mm_HandSolderR5, R7
11.5uFLibrary:C_Rect_L22mm_W8.5mm_P20.00mm_MKTC4
1100RResistor_SMD:R_0805_2012Metric_Pad1.20x1.40mm_HandSolderR4
1100nFCapacitor_SMD:C_1206_3216Metric_Pad1.33x1.80mm_HandSolderC6
1100uFCapacitor_SMD:CP_Elec_6.3x9.9C5
110RResistor_SMD:R_0805_2012Metric_Pad1.20x1.40mm_HandSolderR2
110nFCapacitor_SMD:C_0805_2012Metric_Pad1.18x1.45mm_HandSolderC2
1120VDiode_THT:D_DO-41_SOD81_P2.54mm_Vertical_KathodeUpD10
1200VDiode_THT:D_DO-41_SOD81_P2.54mm_Vertical_KathodeUpD9
122T, 330T, 18TLibrary:Transformer_THT_E20_1P_2ST1
124VDiode_THT:D_DO-41_SOD81_P2.54mm_Vertical_KathodeUpD4
12N7002KPackage_TO_SOT_SMD:SOT-23Q2
1470nFCapacitor_SMD:C_1206_3216Metric_Pad1.33x1.80mm_HandSolderC1
147nFCapacitor_SMD:C_0805_2012Metric_Pad1.18x1.45mm_HandSolderC3
14k7Resistor_SMD:R_0805_2012Metric_Pad1.20x1.40mm_HandSolderR1
168kResistor_THT:R_Axial_DIN0309_L9.0mm_D3.2mm_P2.54mm_VerticalR10
168kResistor_SMD:R_0805_2012Metric_Pad1.20x1.40mm_HandSolderR8
1LM2577T-ADJPackage_TO_SOT_THT:TO-220F-5_P3.4x2.06mm_StaggerOdd_Lead1.86mm_VerticalU1
1TIC116Package_TO_SOT_THT:TO-220-3_VerticalQ3
1Transformer_1P_1SPackage_DIP:DIP-4_W10.16mm_LongPadsT2
1UF4007Diode_THT:D_DO-41_SOD81_P5.08mm_Vertical_KathodeUpD7
1UF4007Diode_THT:D_DO-41_SOD81_P2.54mm_Vertical_AnodeUpD2
1UF4007Diode_THT:D_DO-41_SOD81_P3.81mm_Vertical_AnodeUpD6

Similar boards

  • 2 layers65 × 44 mmDC DC Boost Converter, the printed circuit board in 3D

    DC DC Boost Converter

    chnChris-229/DC-DC-Boost-Converter

    A custom DC-DC boost converter designed in KiCad using the LM2577-ADJ switching regulator.

    11 parts
  • 2 layers90.2 × 44.4 mmEnergieplatine, the printed circuit board in 3D

    Energieplatine

    entwickler-brandenburg/Tutorprojekt_Energieplatine

    41 parts
  • 2 layers68 × 89 mmParanoiaBox, the printed circuit board in 3D

    ParanoiaBox

    profdc9/ParanoiaBox

    A standalone elliptic curve/AES file encryption and decryption device

    60 parts17
  • 2 layers96.3 × 98 mmAquarium, the printed circuit board in 3D

    Aquarium

    baranovskiykonstantin/aquarium

    Control the lighting and the heating of the aquarium.

    73 parts11
  • 2 layers100 × 70 mmMotorDriver, the printed circuit board in 3D

    MotorDriver

    JeyRunner/actonator

    3D printable robot actuator with belt-driven gearbox and custom FOC driver board.

    177 parts10MIT
  • 2 layers156.5 × 67.5 mmNixieScanDisplay, the printed circuit board in 3D

    NixieScanDisplay

    profdc9/NixieClock

    A Nixie clock that uses IN-14 tubes and very generic components that can be easily sourced.

    106 parts10
  • 4 layers147.8 × 77 mm2xBLDCPicoV3, the printed circuit board in 3D

    2xBLDCPicoV3

    AmericanRework/Pico-2x-BLDC

    One RP2040 Pico drives two brushless motors! SimpleFOC + Halls + 2304 drivers + TO-220 mosfets or IGBTs. Plugs directly into 450x automower motors.

    135 parts7
  • 2 layers373 × 132.3 mmSolarinverter, the printed circuit board in 3D

    Solarinverter

    cpipero/solarinverter

    Kicad Project to build a programmable Solar Inverter

    370 parts5CC0-1.0

Questions

How big is the Board v09 PCB?

It measures 46.2 × 31 mm and has 2 copper layers, 1.6 mm thick.

What parts does the Board v09 use?

37 parts, built around the LM2577T-ADJ, 2N7002K and UF4007. The full list of its parts is on this page, with links to each part's symbol and footprint where PCBKit's library has them.

Where can I download the Board v09 KiCad files?

From the nelsonyamamoto/uC-CDI repository on GitHub, at the commit this page was made from: the board is board-v09.kicad_pcb and its schematic board-v09.kicad_sch. PCBKit opens the board in the browser, with nothing to install.

Can I use the Board v09 design in my own project?

Its repository states no licence, so its author keeps all rights: ask nelsonyamamoto before reusing the design.