
OSO BOOK B1
joeycastillo/The-Open-Book
For details on how to build, test and use Open Book, I've made documentation available here.

solid-state CD-ROM drive for the Commodore CDTV
MatshitaPico is an open-source printed circuit board by na103, from the na103/MatshitaPico repository on GitHub. It is a 4-layer board of 218.4 × 110 mm with 66 parts on 155 nets, routed with 872 tracks and 62 vias.
It is built around the 74LS245SC, 10067847-011RLF and BAT54, with the MBR120 among its other parts. Its parts include 23 resistors, 20 capacitors, 6 ICs, 3 connectors and 2 diodes. It belongs with the retro computing and games boards and the RP2040 and FPGA and CPLD boards of this library.
MatshitaPico is a solid-state replacement for the optical CD-ROM drive of the Commodore CDTV: BIN/CUE disc images stored on a microSD card take the place of the optical mechanism.
Why: many CDTV drives have a worn-out laser and cannot be repaired, and no drop-in replacement has ever existed. This project keeps these machines alive.
This repository contains the CPLD design (HDL), technical documentation, RP2350 firmware, KiCad hardware project of beta board and the Amiga-side
mpdisk.device+ boot CD builder for hardfiles.
Because of the limited turnout in the project's closed beta testing, I have decided to open MatshitaPico testing up to the whole Amiga community.
The final version should not differ much from this first one, apart from an ATF1508 CPLD in a TQFP-100 package, programmable in-circuit through a JTAG connector. The key point for the final version is the PCB layout: it must be designed together with a 3D-printed mounting bracket. The original eject button could also be reused as a control button.
This first version is installable — as you can see from the photos here — but several modifications are needed to fit it. When I laid out the PCB I did not worry about its dimensions.
The CDTV service manual contains no schematic for the CD-ROM subsystem: all of the CD-ROM electronics (CD-DSP, the Sanyo LC8951 decoder, the drive's own microcontroller) live on a PCB inside the drive mechanism, not on the motherboard. The motherboard only carries the host side — the DMAC (U36), the 6525/TPI (U32) and glue logic — which talks to the drive through connector CN9 (42 pins, sheet 10 of schematic #252605).
→ CN9 is the emulation point. The device plugs into CN9 and pretends to be the entire drive. The LC8951 does not interpret commands (it is a host↔µC FIFO mailbox); the replacement emulates both the LC8951 host interface and the drive µC command protocol (the proprietary CDTV/Sony command set).
CDTV (CN9, 5 V TTL)
| DB0-7, _HWR/_HRD/_CMD/_STEN/_DTEN/DRQ/_ENABLE/_STCH + RESET
v
CPLD ATF1508AS (5 V, 128 macrocells, PLCC84, JTAG; socketed, programmed out of circuit)
| - real-time 5 V front-end; host-interface FSM (DRQ mode)
| - clock division C16M -> BCLK/LRCK; SCOR / subcode generation
| <- level shifting 5 V <-> 3.3 V (SN74CBTD16211 bus switch, no DIR, 5 V clamp)
v
MCU RP2350 / Raspberry Pi Pico 2 (3.3 V)
- drive command protocol - BIN/CUE from SD
- I2S audio 44.1 kHz (PIO) - subcode Q - UI (NEXT + LED)
+ 16.9344 MHz crystal oscillator (C16M, DIP14 metal-can 5 V TTL)Key constraint: the CN9 bus is 5 V TTL and the RP2350 is not 5 V-tolerant, so a
native 5 V front-end is required (ATF1508AS, the AS variant, not ASV). The CPLD
performs four things in parallel — master clock, I2S audio, subcode, host DMA — plus command
glue logic; the heavy protocol logic runs on the RP2350.
The CPLD is the only chip that faces CN9 (a pure 5 V domain). It contains:
clkgen — derives the audio clocks (BCLK, LRCK, frame sync) from the C16M
master clock (16.9344 MHz = 384 x 44.1 kHz), so the audio stays phase-coherent with the
motherboard DAC (Sanyo LC7883M).host_if — the LC8951-style host-interface FSM: it captures host commands (async latch
on the rising edge of _HWR), drives status replies over _HRD/_STEN, and runs the DMA
data path in DRQ mode (DRQ high = byte ready). EOP is not on CN9 — the DMAC counts
it — so ending a sector is just lowering DRQ.SBCP/SCOR/EFFK; SCCK is a host input) and
buffering of DATA/EMPHASIS from the RP2350.cdtv.cpp from WinUAE (plus cdtvcr.cpp for the CDTV-CR variant) is a complete emulation of
the DMAC + 6525 + LC8951 + command protocol. It is the executable specification the
firmware is ported from. (The WinUAE sources are not redistributed here — see the WinUAE
project.) The CDTV extended ROM is the real host-side protocol engine.
0x01 seek · 0x02 read · 0x04/0x05 motor on/off · 0x09/0x0a play LSN/MSF ·
0x0b play track range · 0x82 clear-error · 0x84 mode set · 0x85 mode sense ·
0x86 capacity · 0x87 subq · 0x8a read TOC · 0xa2/0xa3 front panel.
The full, byte-level command reference — including the vendor 0x6x hardfile page — is in
docs/drive-commands.md.
The device is functionally complete on real hardware: data boot, persistent disc change, CD audio (play / pause / skip / stop), CD+G graphics, and the activity LED all work on a real CDTV.
mpdisk.device)With the firmware built with ENABLE_MPDISK, .hdf hard-disk images in the root of the SD
card become read/write Amiga units MPD0..MPD3, served through the CD controller itself
(no extra hardware). A small boot CD loads mpdisk.device, mounts the hardfiles and hands the
system over to MPD0:, so a CDTV can run Workbench from a writable disk. The Amiga sources and
the boot CD builder are in amiga/ and tools/ — see
amiga/README.md.
Thankyou to all the people who have support this project.
Andrea Quagliarini, Mirco Gaggiottini, Carlo Santagostino, Federico Di Dato.
This work is licensed under the Creative Commons Attribution 4.0 International License
(CC BY 4.0). See LICENSE. You are free to share and adapt the material for any
purpose, provided you give appropriate credit.
If you found this my work useful, please consider buying me a cup of coffee if you want:

| Qty | Value | Footprint | References |
|---|---|---|---|
| 17 | 100nF | Capacitor_SMD:C_1206_3216Metric_Pad1.33x1.80mm_HandSolder | C1, C2, C3, C4, C5, C6, C7, C8, C10, C11, C12, C13, C17, C18, C19, C20 +1 |
| 8 | 47K | Resistor_SMD:R_1206_3216Metric_Pad1.30x1.75mm_HandSolder | R4, R5, R6, R7, R8, R9, R10, R11 |
| 6 | 100R | Resistor_SMD:R_1206_3216Metric_Pad1.30x1.75mm_HandSolder | R15, R17, R18, R19, R20, R21 |
| 4 | 10K | Resistor_SMD:R_1206_3216Metric_Pad1.30x1.75mm_HandSolder | R1, R2, R3, R22 |
| 2 | 10uF | Capacitor_THT:CP_Radial_D5.0mm_P2.50mm | C15, C16 |
| 2 | 1K | Resistor_SMD:R_1206_3216Metric_Pad1.30x1.75mm_HandSolder | R14, R16 |
| 2 | 470R | Resistor_SMD:R_1206_3216Metric_Pad1.30x1.75mm_HandSolder | R12, R13 |
| 2 | 74LS244_Split | Package_SO:SOIC-20W_7.5x12.8mm_P1.27mm | U4, U6 |
| 1 | 0R/100R | Resistor_SMD:R_1206_3216Metric_Pad1.30x1.75mm_HandSolder | R23 |
| 1 | 10067847-011RLF | MatshitaPico_Library:10067847011RLF | SD1 |
| 1 | 16.9344M | Oscillator:Oscillator_DIP-14 | Y1 |
| 1 | 1K | Resistor_THT:R_Array_SIP5 | RN2 |
| 1 | 2-1825027-0 | MatshitaPico_Library:218250270 | SW1 |
| 1 | 2.2K | Resistor_THT:R_Array_SIP9 | RN1 |
| 1 | 47uF | Capacitor_THT:CP_Radial_D5.0mm_P2.50mm | C14 |
| 1 | 61204021721 | MatshitaPico_Library:61204021721 | J2 |
| 1 | 641737-1 | MatshitaPico_Library:641737-1 | J1 |
| 1 | 74LS245 | Package_SO:SOIC-20W_7.5x12.8mm_P1.27mm | U3 |
| 1 | 74LS541 | Package_SO:SOIC-20W_7.5x12.8mm_P1.27mm | U5 |
| 1 | ATF1508ASx-xxJx84 | Package_LCC:PLCC-84_THT-Socket | U1 |
| 1 | BAT54 | MatshitaPico_Library:SODFL3616X98N | D2 |
| 1 | CDROM INTERFACE CD AUDIO | Connector_JST:JST_PH_S3B-PH-K_1x03_P2.00mm_Horizontal | J3 |
| 1 | JP-BENCH | Jumper:SolderJumper-2_P1.3mm_Open_RoundedPad1.0x1.5mm | JP1 |
| 1 | MBR120 | MatshitaPico_Library:SODFL3616X98N | D1 |
| 1 | RaspberryPi_Pico | MatshitaPico_Library:RaspberryPi_Pico_Common_no_wifi | A1 |
| 1 | SN74CBTD16211DGGR | MatshitaPico_Library:SOP50P810X120-56N | U2 |
The 61 most common of 66 parts.

joeycastillo/The-Open-Book
For details on how to build, test and use Open Book, I've made documentation available here.

ElectronicCats/Minino
Minino is an original multiprotocol and multiband board made for sniffing, communicating, and attacking IoT devices. It was designed as a mini Cat that integrates the powerful ESP32C6, GPS, microSD and OLED.

LouDnl/USBSID-Pico
USBSID-Pico is a RPi Pico (RP2040/W RP2350/W) based board for interfacing one or two MOS SID chips and/or hardware SID emulators over (WEB)USB with your computer, phone, ASID supporting player or USB midi controller

jpconstantineau/NRF52-Board
This Repository is a collection of NRF5x boards.



wizarddata/Blue-Wizard-Mod
Bluetooth Controller for the Kinesis Advantage line of keyboards using the BlueMicro firmware

It measures 218.4 × 110 mm and has 4 copper layers, 1.6 mm thick.
66 parts, built around the 74LS245SC, 10067847-011RLF, BAT54 and MBR120. The full list of its parts is on this page, with links to each part's symbol and footprint where PCBKit's library has them.
From the na103/MatshitaPico repository on GitHub, at the commit this page was made from: the board is kicad/MatshitaPico/MatshitaPico.kicad_pcb and its schematic kicad/MatshitaPico/MatshitaPico.kicad_sch. PCBKit opens the board in the browser, with nothing to install.
Its repository states no licence, so its author keeps all rights: ask na103 before reusing the design.