Skip to the content
2 layers85 × 115 mmOSO BOOK B1, the printed circuit board in 3D

For details on how to build, test and use Open Book, I've made documentation available here.

Size
85 × 115 mm
Copper layers
2
Thickness
1 mm
Parts
76
Nets
77
Pads
353
Tracks, vias
710, 164
Pours
2
Routed
Yes
KiCad
KiCad 7 (file 20221018)
Created
13 Aug 2019
Updated
5 Dec 2023

Overview

OSO BOOK B1 is an open-source printed circuit board by joeycastillo, from the joeycastillo/The-Open-Book repository on GitHub, published under the CC-BY-SA-4.0 licence. It is a 2-layer board of 85 × 115 mm with 76 parts on 77 nets, routed with 710 tracks and 164 vias.

It is built around the ESP32-S3-WROOM-1-N8, XC6220B331MR-G and MBR0530, with the DMG3415U and MBR120 among its other parts. Its parts include 19 capacitors, 11 resistors, 8 connectors, 5 ICs and 4 diodes. It belongs with the ESP32 boards of this library.

Main components

5

README

README.md

The Open Book: Project Reboot

A note from the project creator: The Open Book was my first real electronics project; the earliest designs date to late 2019. I have learned a lot since those early days, and as such, here three years later, I am hitting reset. At this time the repository contains a version of the Open Book designed around the Raspberry Pi Pico. It's optimized for low part count and easy hand assembly, but it runs on AAA batteries and may not be as svelte as some folks might prefer. At a later date, I hope to design a followup with built-in LiPo charging and a slimmer profile, but at this time, this version of the book is the quickest path to getting hardware in people's hands so that we can start hacking on firmware together.

For details on how to build, test and use Open Book, I've made documentation available here.

The original Open Book repository has been archived in a branch called original.

The Open Book firmware, called libros, is under development here. It's a goddamn mess in some ways, and in dire need of some documentation, but for the moment it does do the job of presenting a list of books stored on an SD card, and letting you read them. The canonical format for books is plain text with the book title on the first line, OR plain text plus some front matter and some ASCII control codes for chapter breaks and formatting, as documented here.

Original Introduction

As a society, we need an open source device for reading. Books are among the most important documents of our culture, yet the most popular and widespread devices we have for reading — the Kobo, the Nook, the Kindle and even the iPad — are closed devices, operating as small moving parts in a set of giant closed platforms whose owners' interests are not always aligned with readers'.

The Open Book aims to be a simple device that anyone with a soldering iron can build for themselves. The Open Book should be comprehensible: the reader should be able to look at it and understand, at least in broad strokes, how it works. It should be extensible, so that a reader with different needs can write code and add accessories that make the book work for them. It should be global, supporting readers of books in all the languages of the world. Most of all, it should be open, so that anyone can take this design as a starting point and use it to build a better book.

State of the Book

At this time, the Pi Pico book is in decent shape if you want to try your hand at building it yourself. You will need to have two custom things fabricated: the Open Book Main Board (which you can get as a bare PCB) and the Castellated E-Paper Driver module (which you'll want to have done as a PCBA job). All the files you will need to send out for this can be found in the Fabrication Files folder in the project root:

  • Upload OSO-BOOK-C1-04-rounded.zip to your PCB fabrication house of choice. It is designed to be a two-layer, 1 mm thick PCB, and you can use either an ENIG or lead-free HASL finish.
  • If you plan to use JLCPCB's economic PCBA service, upload all three files in OSO-BOOK-C2-01 to JLCPCB. Opt for a 1 mm thick lead-free HASL finish. Note that the board is slightly wider than it needs to be, just to meet the minimum size requirements for this service.
  • If you plan to use PCBWay's PCBA service, upload all three files in OSO-BOOK-C2-02 to PCBWay. Once again, opt for a 1 mm thick lead-free HASL finish.

Other Parts:

The Open Book is open source hardware: you should feel free to build one yourself, order parts for ten and do a workshop at your local maker space, or even buy parts for fifty and sell them as kits.

Please steal this book.

I plan to add more documentation in the new year, but until then, this half-hour video walks through building one Open Book board in real-time.

Forking and tweaking the boards

  • Design files for the Open Book main board can be found in the OSO-BOOK-C1 folder. It's a KiCad project.
  • Design files for the castellated e-paper driver module can be found in the OSO-BOOK-C2 folder. Alas, they are Eagle projects that predate my move to KiCad. There are two versions: an older version that was successfully fabricated with JLCPCB's economic PCBA service (OSO-BOOK-C2-01), and a newer version successfully fabricated using PCBWay's PCBA service (OSO-BOOK-C2-02). Both work great.

License

Different components of the project are licensed differently, see LICENSE.md.

Parts

76
QtyValueFootprintReferences
91µFCapacitor_SMD:C_0805_2012MetricC9, C12, C13, C14, C15, C16, C17, C18, C19
7SW_PushTACT_PANA-EVQ:TACT_PANA-EVQ-BUTTONPADB3, B4, B5, B6, B7, B8, B9
610µFCapacitor_SMD:C_1206_3216MetricC1, C2, C3, C4, C5, C8
4FiducialFiducial:Fiducial_1mm_Mask2mmFID1, FID2, FID3, FID4
4MountingHoleMountingHole:MountingHole_2.7mm_M2.5H1, H2, H3, H4
31kResistor_SMD:R_0805_2012MetricR3, R9, R10
3MBR0530Diode_SMD:D_SOD-123D1, D2, D3
24.7µFCapacitor_SMD:C_0805_2012MetricC10, C11
25.1kResistor_SMD:R_0805_2012MetricR1, R2
2JST-PH3Connector_JST:JST_SH_SM03B-SRSS-TB_1x03-1MP_P1.00mm_HorizontalJ5, J7
2Jumper_2_OpenJumper:SolderJumper-2_P1.3mm_Open_TrianglePad1.0x1.5mmJP1, JP2
2LOGOOddly_Specific_Artwork:oso-logotype-2mmG***, G***
2SW_PushButton_Switch_SMD:Panasonic_EVQPUJ_EVQPUAB1, B2
2TBDCapacitor_SMD:C_0805_2012MetricC6, C7
10.47Resistor_SMD:R_0805_2012MetricR6
110Resistor_SMD:R_0805_2012MetricR8
1100KResistor_SMD:R_0805_2012MetricR11
110KResistor_SMD:R_0805_2012MetricR5
110µHInductor_SMD:L_Taiyo-Yuden_MD-4040L1
11MResistor_SMD:R_0805_2012MetricR7
1200kResistor_SMD:R_0805_2012MetricR4
122µHInductor_SMD:L_1210_3225MetricL2
132.768 kHzCrystal:Crystal_SMD_3215-2Pin_3.2x1.5mmY1
1Conn_01x02_MountingPinConnector_Molex:Molex_PicoBlade_53261-0271_1x02-1MP_P1.25mm_HorizontalJ2
1Conn_01x06Connector_FFC-FPC:TE_0-1734839-6_1x06-1MP_P0.5mm_HorizontalJ4
1Conn_01x24Connector_FFC-FPC:TE_2-1734839-4_1x24-1MP_P0.5mm_HorizontalJ3
1Conn_ARM_JTAG_SWD_10Connector_PinHeader_1.27mm:PinHeader_2x05_P1.27mm_Vertical_SMDJ8
1DMG3415Package_TO_SOT_SMD:SOT-23Q1
1ESP32-S3-WROOM-1RF_Module:ESP32-S3-WROOM-1U2
1JST-PH4Connector_JST:JST_SH_SM04B-SRSS-TB_1x04-1MP_P1.00mm_HorizontalJ6
1LOGOOddly_Specific_Artwork:oso-bear-8mm-wideG***
1MBR120Diode_SMD:D_SOD-123D4
1MCP73831-2-OTPackage_TO_SOT_SMD:SOT-23-5U4
1MEM2075MEM2075-00-140-01-A:GCT_MEM2075-00-140-01-AU3
1Q_NMOS_GSDPackage_TO_SOT_SMD:SOT-23Q3
1Q_PMOS_GSDPackage_TO_SOT_SMD:SOT-23Q2
1R1218Package_TO_SOT_SMD:SOT-23-6U5
1R_Pack04_SplitResistor_SMD:R_Array_Concave_4x0603RN1
1USB_C_Receptacle_USB2.0Connector_USB:USB_C_Receptacle_HRO_TYPE-C-31-M-12J1
1XC6220B331MR-GPackage_TO_SOT_SMD:SOT-23-5U1

More from joeycastillo/The-Open-Book

1
  • 2 layers85 × 115 mmOSO BOOK C1, the printed circuit board in 3D

    OSO BOOK C1

    joeycastillo/The-Open-Book

    For details on how to build, test and use Open Book, I've made documentation available here.

    38 parts8.1kCC-BY-SA-4.0

Similar boards

  • 2 layers80 × 107.5 mmMinino, the printed circuit board in 3D

    Minino

    ElectronicCats/Minino

    Minino is an original multiprotocol and multiband board made for sniffing, communicating, and attacking IoT devices. It was designed as a mini Cat that integrates the powerful ESP32C6, GPS, microSD and OLED.

    79 parts183GPL-3.0
  • 2 layers60 × 121.3 mmEko badge-2024, the printed circuit board in 3D

    Eko badge-2024

    ElectronicCats/badge-EKOParty-2024

    Badge Oficial de EkoParty 2024

    63 parts2
  • 2 layers87.5 × 77.5 mmPanel, the printed circuit board in 3D

    Panel

    jpconstantineau/NRF52-Board

    This Repository is a collection of NRF5x boards.

    143 parts100BSD-3-Clause
  • 4 layers33.1 × 64.7 mmNrg3, the printed circuit board in 3D

    Nrg3

    panStamp/kicad

    Kicad projects

    135 parts15GPL-2.0
  • 2 layers45 × 40 mmCircuitPythonBadge v1 2, the printed circuit board in 3D

    CircuitPythonBadge v1 2

    neubauek/CircuitPythonBadge

    Open Source Hardware Circuit Python Badge

    91 parts4
  • 2 layers50.8 × 22.9 mmAdafruit Feather M4 Express, the printed circuit board in 3D

    Adafruit Feather M4 Express

    ryanfobel/Feather-M4-Express-clone.kicad

    KiCad clone of Adafruit's Feather M4 Express PCB design files

    109 parts1
  • 4 layers54 × 35 mmBike, the printed circuit board in 3D

    Bike

    InfinityTech100/Bike-Mini-speedo

    67 parts
  • 2 layers89 × 76.1 mmGSRT Badge, the printed circuit board in 3D

    GSRT Badge

    ril3y/GSRT-ATL-Badge

    GSRT Badge - 2018 Atlanta

    62 partsMIT

Questions

How big is the OSO BOOK B1 PCB?

It measures 85 × 115 mm and has 2 copper layers, 1 mm thick.

What parts does the OSO BOOK B1 use?

76 parts, built around the ESP32-S3-WROOM-1-N8, XC6220B331MR-G, MBR0530 and DMG3415U. The full list of its parts is on this page, with links to each part's symbol and footprint where PCBKit's library has them.

Where can I download the OSO BOOK B1 KiCad files?

From the joeycastillo/The-Open-Book repository on GitHub, at the commit this page was made from: the board is OSO-BOOK-B1/OSO-BOOK-B1.kicad_pcb and its schematic OSO-BOOK-B1/OSO-BOOK-B1.kicad_sch. PCBKit opens the board in the browser, with nothing to install.

Can I use the OSO BOOK B1 design in my own project?

Its repository publishes it under the CC-BY-SA-4.0 licence: you may reuse it on that licence's terms (keep the author's notice, and for a copyleft licence share your changes alike).