2 layers273 × 146 mm
PS2BaseMount
MRKane05/PS2BaseMount
The KiCad project for the base mount for the "Junkstation" PS2 portable project
98 parts
2 layers
PS2Board PreController
MRKane05/PS2BaseMountThe KiCad project for the base mount for the "Junkstation" PS2 portable project
- Copper layers
- 2
- Thickness
- 1.6 mm
- Parts
- 26
- Nets
- 166
- Pads
- 229
- Tracks, vias
- 0, 0
- Routed
- Not yet
- KiCad
- KiCad 5 (file 20171130)
- Created
- 11 Dec 2024
- Updated
- 11 Dec 2024
Overview
PS2Board PreController is an open-source printed circuit board by MRKane05, from the MRKane05/PS2BaseMount repository on GitHub. It is a 2-layer board with 26 parts on 166 nets.
It is built around the LM358 and RJ45. Its parts include 6 connectors, 5 ICs, 4 resistors and 1 transistor. It belongs with the AVR (ATmega, ATtiny) boards of this library.
Main components
2README
README.mdThis is a dump of the KiCad project for the Junkstation PS2 project I made a few years ago. I'm really just backing it up for prosperity. I'm taking no responsibility for this and it really should be used only as reference.
It's worth noting that there are a couple of mistakes on the board that I haven't fixed: -The Ethernet wiring for the Mango isn't correct, and troubleshooting it was exceedingly difficult, so much so that I didn't write it down when I got it right, I just put the lid on it -The Ethernet lines for the Mango shouldn't be pulled down to Ground but pulled to the "R0" pin on the Mango. This allows a successful ethernet connection -The SD Card slot wired up for game loading through the memory card port is correctly wired
Parts
26| Qty | Value | Footprint | References |
|---|---|---|---|
| 2 | PS2_ControlMount | PS2BaseMount:PS2_BoardMountFootprint | P1, P2 |
| 1 | 10P_LFT | Connector_FFC-FPC:Hirose_FH12-10S-0.5SH_1x10-1MP_P0.50mm_Horizontal | m1 |
| 1 | 10P_RHT | Connector_FFC-FPC:Hirose_FH12-10S-0.5SH_1x10-1MP_P0.50mm_Horizontal | m2 |
| 1 | 1K | Resistor_SMD:R_2512_6332Metric_Pad1.52x3.35mm_HandSolder | R2 |
| 1 | 4.7K | Resistor_SMD:R_2010_5025Metric_Pad1.52x2.65mm_HandSolder | R1 |
| 1 | Arduino_Nano_v3.x | Module:Arduino_Nano_WithMountingHoles | A1 |
| 1 | AudioAmp | PS2BaseMount:PAM8803_AudioAmp | U1 |
| 1 | Audio_Left | Connector_JST:JST_ZE_SM02B-ZESS-TBT_1x02-1MP_P1.50mm_Horizontal | U4 |
| 1 | Audio_Right | Connector_JST:JST_ZE_SM02B-ZESS-TBT_1x02-1MP_P1.50mm_Horizontal | U5 |
| 1 | Fan | PS2BaseMount:2Point_Mount | M4 |
| 1 | Fan_J+ | Jumper:SolderJumper-2_P1.3mm_Open_RoundedPad1.0x1.5mm | R3 |
| 1 | Fan_J- | Jumper:SolderJumper-2_P1.3mm_Open_RoundedPad1.0x1.5mm | R4 |
| 1 | LM358 | PS2BaseMount:LM358(SMD) | U2 |
| 1 | MJE3305 | Package_TO_SOT_THT:TO-126-3_Vertical | Q1 |
| 1 | PJ30240 | PS2BaseMount:AudioJack_PJ30240 | U3 |
| 1 | PS2AVPort | PS2BaseMount:PS2_AVPort_Complete | M1 |
| 1 | PS2AVPort_SideMount | PS2BaseMount:PS2_AVPort_Complete_MountSilk | M5 |
| 1 | PS2_MemCardMount | PS2BaseMount:PS2_MemCardMountPoints | P3 |
| 1 | RJ45 | Connector_RJ:RJ45_Amphenol_54602-x08_Horizontal | J3 |
| 1 | R_POT_US | Potentiometers:Potentiometer_Triwood_RM-065 | RV1 |
| 1 | TS_LFT | Connector_JST:JST_GH_SM05B-GHS-TB_1x05-1MP_P1.25mm_Horizontal | M2 |
| 1 | TS_RHT | Connector_JST:JST_GH_SM05B-GHS-TB_1x05-1MP_P1.25mm_Horizontal | M3 |
| 1 | Thermistor_PTC | PS2BaseMount:2Point_Mount | TH1 |
| 1 | USB_A_Dual | Connector_USB:USB_A_Wuerth_61400826021_Horizontal_Stacked | J2 |
| 1 | USB_B | PS2BaseMount:USB_A_Custom_Throughhole | J1 |
More from MRKane05/PS2BaseMount
3- 2 layers
PS2BaseMount NanoPi
MRKane05/PS2BaseMount
The KiCad project for the base mount for the "Junkstation" PS2 portable project
58 parts - 2 layers
PreControlChip
MRKane05/PS2BaseMount
The KiCad project for the base mount for the "Junkstation" PS2 portable project
19 parts
Similar boards
- 4 layers61 × 81 mm
- 2 layers100 × 99.9 mm
- 4 layers44.3 × 53.5 mm
PicoSteamControl
jeremyrode/PicoSteamControl
Pico control for a Leisure Steam One Touch shower steamer with capacitive touch detection.
18 parts1Unlicense - 2 layers125 × 120 mm
- 4 layers118.1 × 105.4 mm
PocketBeagleCommandStation SMD
RobertPHeller/CommandStationsAndBoosters
Command Stations and Boosters
172 parts - 2 layers64.8 × 74.5 mm
ReadingLampController
vsi5004/ReadingLampController
A repurposing of my LCC Lighting Controller hardware into a customizable, Matter enabled, RGBW reading lamp
67 parts - 2 layers55 × 135.3 mm
MSG25
ZeniteSolar/MSG25
Módulo de sensoriamento geral para medição de 4 tensões e 3 temperaturas
131 parts - 2 layers105.6 × 73.3 mm
STM32F767ZI LCC PNET Router
RobertPHeller/RPi-RRCircuits
A collection of circuit designs for various MCUs, not just Raspberry Pis relating to Model Railroading
52 parts24
Questions
What parts does the PS2Board PreController use?
26 parts, built around the LM358 and RJ45. The full list of its parts is on this page, with links to each part's symbol and footprint where PCBKit's library has them.
Where can I download the PS2Board PreController KiCad files?
From the MRKane05/PS2BaseMount repository on GitHub, at the commit this page was made from: the board is PS2Board_PreController.kicad_pcb. PCBKit opens the board in the browser, with nothing to install.
Can I use the PS2Board PreController design in my own project?
Its repository states no licence, so its author keeps all rights: ask MRKane05 before reusing the design.