motthomasn/GPS-IMU_CAN_Module2Teensy 3.2 based controller board designed to collect GPS & IMU data from SkyTraq Venus838LPx and Bosch BNO055 breakout boards and transmit the data via CAN-Bus
CBR015-0005 GPS CAN MODULE PCB is an open-source printed circuit board by motthomasn, from the motthomasn/GPS-IMU_CAN_Module repository on GitHub, published under the GPL-3.0 licence. It is a 2-layer board of 63 × 46 mm with 15 parts on 52 nets, routed with 134 tracks and 14 vias.
It is built around the MCP2551-I/SN-HG and TSR 1-2450. Its parts include 6 ICs, 5 capacitors, 2 resistors, 1 connector and 1 switch. It belongs with the radio and wireless and interfaces and adapters boards and the NXP (LPC, Kinetis, i.MX RT) boards of this library.
This folder contains the KiCad files for the GPS-IMU CAN Module
| Qty | Value | Footprint | References |
|---|---|---|---|
| 3 | 10nF | Capacitors_SMD:C_0805_HandSoldering | C3, C4, C5 |
| 1 | 100nF | Capacitors_SMD:C_0805_HandSoldering | C2 |
| 1 | 120 | Resistors_SMD:R_0805_HandSoldering | R2 |
| 1 | 18K | Resistors_SMD:R_0805_HandSoldering | R1 |
| 1 | 22µF | Capacitors_SMD:C_0805_HandSoldering | C1 |
| 1 | 3001 | SamacSys_Parts:3001 | U6 |
| 1 | ADAFRUIT_BNO055 | User Libraries:ADAFRUIT_BNO055_BREAKOUT | U5 |
| 1 | Conn_01x04_Male | Pin_Headers:Pin_Header_Angled_2x02_Pitch2.54mm | J1 |
| 1 | IKD0103101 | SamacSys_Parts:IKD0103101 | S1 |
| 1 | MCP2551-I-SN | Housings_SOIC:SOIC-8_3.9x4.9mm_Pitch1.27mm | U3 |
| 1 | TEENSY_3.2_BASIC | User Libraries:TEENSY_3.2_BASIC | U1 |
| 1 | TSR_1-2450 | Converters_DCDC_ACDC:DCDC-Conv_TRACO_TSR-1 | U2 |
| 1 | VENUS838FLPx_BREAKOUT | User Libraries:VENUS838FLPx_BREAKOUT | U4 |
corygrant/dingoPDM
Hardware - dingoPDM is an open source, affordable automotive PDM (Power Distribution Module). Pre-assembled and tested units are available or the design can be used to build a DIY version.
hberntsen/mhi-ac-ctrl-esp32
Control MHI Airconditioning locally using your own ESP32 series chip!
idlehandsdev/shark_bait
The files and firmware for the Shark Bait wireless pumping system.
It measures 63 × 46 mm and has 2 copper layers, 1.6 mm thick.
15 parts, built around the MCP2551-I/SN-HG and TSR 1-2450. The full list of its parts is on this page, with links to each part's symbol and footprint where PCBKit's library has them.
From the motthomasn/GPS-IMU_CAN_Module repository on GitHub, at the commit this page was made from: the board is KiCad_Files/CBR015-0005_GPS_CAN_MODULE_PCB.kicad_pcb. PCBKit opens the board in the browser, with nothing to install.
Its repository publishes it under the GPL-3.0 licence: you may reuse it on that licence's terms (keep the author's notice, and for a copyleft licence share your changes alike).
