Skip to the content
2 layers51.6 × 26.8 mmMHI AC CTRL, the printed circuit board in 3D

Control MHI Airconditioning locally using your own ESP32 series chip!

Size
51.6 × 26.8 mm
Copper layers
2
Thickness
1.6 mm
Parts
8
Nets
33
Pads
58
Tracks, vias
37, 3
Pours
1
Routed
Yes
KiCad
KiCad 10.0 (file 20260206)
Created
7 Feb 2023
Updated
2 Nov 2026

Overview

MHI AC CTRL is an open-source printed circuit board by hberntsen, from the hberntsen/mhi-ac-ctrl-esp32 repository on GitHub, published under the MIT licence. It is a 2-layer board of 51.6 × 26.8 mm with 8 parts on 33 nets, routed with 37 tracks and 3 vias.

It is built around the TSR 1-2450. Its parts include 3 capacitors, 3 ICs, 1 resistor and 1 connector. It belongs with the home automation and IoT boards of this library.

Main components

1

README

README.md

mhi-ac-ctrl-esp32

Control Mitsubishi Heavy Industries Airconditioning locally through ESPHome!

This repository contains a custom component for ESPHome. It is inspired by @absalom-muc's MHI-AC-Ctrl, @mriksman's esp32 homekit implementation and @ginkage's MHI-AC-Ctrl-ESPHome. Compared to the popular implementation of @absalom-muc and @ginkage, this project is a fully redesigned implementation aiming for high reliability. It achieves that by using the hardware SPI peripheral instead of a software based implementation.

Hardware

Officialy supported (tested by @hberntsen):

Community supported:

Note that it is also possible to re-use custom PCBs designed for the ESP8266 with a supported ESP32 series chip. For example with the Lilygo T-OI Plus, see this discussion.

Not supported

ESP32 chips without RMT peripheral. At the moment of writing that's the ESP32-C2 and ESP32-C61. The RMT is used to derive an SPI CS signal from the clock. Users of these chips might try an older version of the code, i.e. commit 3ddb8cb, that uses timers and interrupts for this.

Getting started

The ESPHome documentation will help you getting started with an ESPHome setup that integrates with your Home Assistant, MQTT or whatever. Then you can merge the relevant parts of the example.yaml configuration file into your own. Once you got that going and want to use an external temperature sensor, have a look at example-external-sensor.yaml for extra settings to do so. The example shows a Bluetooth sensor but any ESPHome temperature sensor will do.

In general, the latest version of ESPHome should work. See the build workflow for the latest version of ESPHome that was tested.

Parts

8
QtyValueFootprintReferences
2100nFCapacitor_THT:C_Disc_D3.0mm_W1.6mm_P2.50mmC2, C3
112KResistor_THT:R_Axial_DIN0207_L6.3mm_D2.5mm_P15.24mm_HorizontalR1
122μF/25VCapacitor_THT:CP_Axial_L10.0mm_D4.5mm_P15.00mm_HorizontalC1
1Conn_01x05Connector_JST:JST_XH_B5B-XH-A_1x05_P2.50mm_VerticalJ1
1ESP-C3-32S-KitMHI-AC-CTRL:ESP-C3-32S-KitU2
1LEVEL-SHIFTER-4CHPackage_SO:SOIC-14_3.9x8.7mm_P1.27mmU3
1TSR_1-2450Converter_DCDC:Converter_DCDC_TRACO_TSR-1_THTU1

Similar boards

  • 4 layers72.4 × 95.3 mmDingoPDM, the printed circuit board in 3D

    DingoPDM

    corygrant/dingoPDM

    Hardware - dingoPDM is an open source, affordable automotive PDM (Power Distribution Module). Pre-assembled and tested units are available or the design can be used to build a DIY version.

    156 parts128MIT
  • 2 layers65 × 74 mmRP2040 MPG and DRO, the printed circuit board in 3D

    RP2040 MPG and DRO

    terjeio/GRBL_MPG_DRO_BoosterPack

    Tiva C BoosterPack for GRBL MPG/DRO

    54 parts46
  • 2 layers127 × 54.3 mmTerraesp, the printed circuit board in 3D

    Terraesp

    fehlfarbe/terraesp

    ESP32 terrarium controller

    83 parts25MIT
  • 2 layers94.8 × 67.2 mmArgo v9-stable rev4, the printed circuit board in 3D

    Argo v9-stable rev4

    SensorsINI/argo

    Code for Autonomous sail boat

    139 parts16
  • 2 layers110 × 75 mmShark bait remote, the printed circuit board in 3D

    Shark bait remote

    idlehandsdev/shark_bait

    The files and firmware for the Shark Bait wireless pumping system.

    65 parts13
  • 2 layers70 × 40 mmRx V1.2, the printed circuit board in 3D

    Rx V1.2

    TRD-B/EasyRC

    Open source RC platform

    52 parts9MIT
  • 2 layers139 × 139 mmScreen driver, the printed circuit board in 3D

    Screen driver

    lambdaBoost/MC6205-graphical-display

    graphical display on old neon plasma screen

    285 parts7

Questions

How big is the MHI AC CTRL PCB?

It measures 51.6 × 26.8 mm and has 2 copper layers, 1.6 mm thick.

What parts does the MHI AC CTRL use?

8 parts, built around the TSR 1-2450. The full list of its parts is on this page, with links to each part's symbol and footprint where PCBKit's library has them.

Where can I download the MHI AC CTRL KiCad files?

From the hberntsen/mhi-ac-ctrl-esp32 repository on GitHub, at the commit this page was made from: the board is kicad/MHI-AC-CTRL/MHI-AC-CTRL.kicad_pcb and its schematic kicad/MHI-AC-CTRL/MHI-AC-CTRL.kicad_sch. PCBKit opens the board in the browser, with nothing to install.

Can I use the MHI AC CTRL design in my own project?

Its repository publishes it under the MIT licence: you may reuse it on that licence's terms (keep the author's notice, and for a copyleft licence share your changes alike).