Skip to the content
2 layers62 × 94 mmM3 dct shift lights, the printed circuit board in 3D
Size
62 × 94 mm
Copper layers
2
Thickness
1.6 mm
Parts
15
Nets
45
Pads
87
Tracks, vias
0, 0
Routed
Not yet
KiCad
KiCad 7 (file 20221018)
Created
9 Apr 2021
Updated
27 Dec 2023

Overview

M3 dct shift lights is an open-source printed circuit board by intervigilium, from the intervigilium/bmw_m3_dct_shift_lights repository on GitHub. It is a 2-layer board of 62 × 94 mm with 15 parts on 45 nets.

It is built around the TSR 1-2450, SFH617A-2 and TPIC6C596N. Its parts include 4 resistors, 3 ICs, 2 capacitors, 2 diodes and 2 connectors. It belongs with the AVR (ATmega, ATtiny) boards of this library.

Main components

3

README

README.md

BMW M3 DCT Cluster Shift Lights Retrofit

BMW M3 DCT Cluster

The M3 DCT instrument cluster has a series of 8 shift lights above the tachometer. These shift lights are normally not active, and do not appear to be possible to activate without having the DCT itself. Fortunately, the cluster's LEDs can be driven by attaching leads to the test points on the ground side, as the LEDs are connected to an onboard 5V rail for power, and a TI 6C596G4 8-bit shift register which acts as a current sink to ground. Grounding each of these LED pairs will light up the corresponding pair.

Retrofit circuit

Instead of attempting to drive the LEDs using the onboard TI 6C596 shift register, we can just connect the LEDs to a shift register of our own and connect that to an Arduino. The sketch here assumes that the shift register is a TI 6C596 as well, and is configured using pins D3-D5, D18-D19. Engine RPM for the BMW E9X series appears to be present on OBD2 port pin 9 as a 12V square wave. This circuit utilizes the 12V RPM signal input circuit from the Chippernut digital shift light project to read the signal, as well as the 5V buck regulator input circuit to provide power.

Cluster modifications

The M3 DCT cluster modifications necessary are detailed in the m3_dct_cluster_gnd_points.jpeg file. Ignore the leads from the LEDs themselves. The important points are circled in black, and correspond to the ground points for the LED pairs. It is necessary to attach leads to these ground points ONLY. You MUST attach leads to the test points AFTER the 127 Ohm resistor (the highlighted points ONLY), not before. Failure to follow this instruction will result in burning out the LEDs due to overcurrent. You will also need to cut a small hole in the cluster enclosure to allow the LED ground lines to connect to the Arduino.

Schematic

The included m3_dct_shift_lights.sch file can be opened with any Eagle schematic compatible program. The schematic only includes the circuit necessary to read the RPM and control the LEDs. It does NOT include the necessary circuit to independently power the Arduino from the car's +12V power sources. The Chippernut development board (https://www.chippernut.com/store/p31/Chipperkit.html) comes with a power pack consisting of a 5V buck converter that can be used for this purpose.

Components

The included bom_m3_dct_shift_lights.csv file contains the list of parts necessary to build the circuit. The BOM list can easily purchased on Digikey. It does not include the Arduino or a board to mount all the components. I highly suggest using the above linked Chippernut development board pack, as it comes with the 5V buck converter as well as a development board, Arduino nano, and enclosure for installation.

Installation

You will need to tap pin 9 of the OBD2 port for the tachometer signal. This needs to be connected where the schematic says "To OBD2 Pin 9". You will also need to provide power and ground, as well as connecting the 8 LED ground lines from the M3 DCT cluster to the shift register (Refer to schematic where it details the LED pairs with the notes that these are on board). I suggest tapping +12V power and ground from the cluster connector pins 9 (+12V) and 18 (ground). I suspect the circuit must be connected to the cluster's ground in order for the LEDs to function. The Arduino and wires can be tucked into the driver's footwell under the panel. I chose to zip tie it near the firewall.

Software Notes

The Arduino sketch has a few constants that can be customized to suit your needs. The activation RPM and the maximum RPM values can be found at the top of the file with the names kActivationRpm and kMaxRpm, respectively. The kActivationRpm variable sets the RPM value at which the first LED will light. The kMaxRpm variable sets the RPM value at which the all the LEDs will start to flash. Any RPM value above the kMaxRpm value will mean the LEDs continue to flash until the RPM drops below the threshold.

Parts

15
QtyValueFootprintReferences
210kResistor_THT:R_Axial_DIN0207_L6.3mm_D2.5mm_P15.24mm_HorizontalR2, R4
11000uFCapacitor_THT:C_Axial_L3.8mm_D2.6mm_P15.00mm_HorizontalC2
1100uFCapacitor_THT:C_Axial_L3.8mm_D2.6mm_P15.00mm_HorizontalC1
11N4148digikey-footprints:Diode_DO-35_P10mmD1
12N3906digikey-footprints:TO-92-3Q1
147kResistor_THT:R_Axial_DIN0207_L6.3mm_D2.5mm_P15.24mm_HorizontalR3
17.5kResistor_THT:R_Axial_DIN0207_L6.3mm_D2.5mm_P15.24mm_HorizontalR1
1Arduino_Nano_v3.xModule:Arduino_NanoA1
1Conn_01x03Connector_JST:JST_GH_SM03B-GHS-TB_1x03-1MP_P1.25mm_HorizontalJ1
1Conn_01x08Connector_JST:JST_GH_SM08B-GHS-TB_1x08-1MP_P1.25mm_HorizontalJ2
1D_SchottkyDiode_THT:D_DO-15_P10.16mm_HorizontalD2
1SFH617A-2Package_DIP:DIP-4_W7.62mmU1
1TPIC6C596Ntpic6c596n:DIP794W45P254L1969H508Q16U3
1TSR_1-2450Converter_DCDC:Converter_DCDC_TRACO_TSR-1_THTU2

Similar boards

  • 2 layersCart programmer, the printed circuit board in 3D

    Cart programmer

    JiggleSoft/atari2600_cart_prog

    Atari 2600 Budget ROM Cartridge, Budget ROM/RAM/Bank Switching Cartridge, Budget Programmer.

    7 parts8
  • 4 layers72.4 × 95.3 mmDingoPDM, the printed circuit board in 3D

    DingoPDM

    corygrant/dingoPDM

    Hardware - dingoPDM is an open source, affordable automotive PDM (Power Distribution Module). Pre-assembled and tested units are available or the design can be used to build a DIY version.

    156 parts128MIT
  • 2 layers51.6 × 26.8 mmMHI AC CTRL, the printed circuit board in 3D

    MHI AC CTRL

    hberntsen/mhi-ac-ctrl-esp32

    Control MHI Airconditioning locally using your own ESP32 series chip!

    8 parts74MIT
  • 2 layers65 × 74 mmRP2040 MPG and DRO, the printed circuit board in 3D

    RP2040 MPG and DRO

    terjeio/GRBL_MPG_DRO_BoosterPack

    Tiva C BoosterPack for GRBL MPG/DRO

    54 parts46
  • 2 layers127 × 54.3 mmTerraesp, the printed circuit board in 3D

    Terraesp

    fehlfarbe/terraesp

    ESP32 terrarium controller

    83 parts25MIT
  • 2 layers94.8 × 67.2 mmArgo v9-stable rev4, the printed circuit board in 3D

    Argo v9-stable rev4

    SensorsINI/argo

    Code for Autonomous sail boat

    139 parts16
  • 2 layers110 × 75 mmShark bait remote, the printed circuit board in 3D

    Shark bait remote

    idlehandsdev/shark_bait

    The files and firmware for the Shark Bait wireless pumping system.

    65 parts13
  • 2 layers70 × 40 mmRx V1.2, the printed circuit board in 3D

    Rx V1.2

    TRD-B/EasyRC

    Open source RC platform

    52 parts9MIT

Questions

How big is the M3 dct shift lights PCB?

It measures 62 × 94 mm and has 2 copper layers, 1.6 mm thick.

What parts does the M3 dct shift lights use?

15 parts, built around the TSR 1-2450, SFH617A-2 and TPIC6C596N. The full list of its parts is on this page, with links to each part's symbol and footprint where PCBKit's library has them.

Where can I download the M3 dct shift lights KiCad files?

From the intervigilium/bmw_m3_dct_shift_lights repository on GitHub, at the commit this page was made from: the board is m3_dct_shift_lights/m3_dct_shift_lights.kicad_pcb and its schematic m3_dct_shift_lights/m3_dct_shift_lights.kicad_sch. PCBKit opens the board in the browser, with nothing to install.

Can I use the M3 dct shift lights design in my own project?

Its repository states no licence, so its author keeps all rights: ask intervigilium before reusing the design.