mosyrf/Oxygen-Monitoring-SystemThis was my second year project as an electrical engineering student, and it was quite difficult because it used an STM32 controller, which I was not familiar with. The project was also considered a failure because it did not produce any final product, only electrical designs and simulations.
Oxygen Monitoring is an open-source printed circuit board by mosyrf, from the mosyrf/Oxygen-Monitoring-System repository on GitHub. It is a 2-layer board of 102.5 × 62 mm with 121 parts on 108 nets, routed with 1,261 tracks and 114 vias.
It is built around the MAX485ED, LM2596S-5.0 and 74HC14, with the RT9193-33GB, SRV05-4 and W5100 among its other parts. Its parts include 45 capacitors, 34 resistors, 13 diodes, 7 ICs and 5 connectors. It belongs with the STM32 boards of this library.
This was my second year project as an electrical engineering student, and it was quite difficult because it used an STM32 controller, which I was not familiar with. The project was also considered a failure because it did not produce any final product, only electrical designs and simulations.
| Qty | Value | Footprint | References |
|---|---|---|---|
| 27 | 100nF | Capacitor_SMD:C_0805_2012Metric | C2, C15, C16, C19, C20, C21, C22, C24, C25, C26, C27, C28, C34, C35, C36, C37 +11 |
| 10 | LED | LED_SMD:LED_0805_2012Metric | D2, D3, D4, D5, D8, D9, D10, D11, D12, D13 |
| 9 | 1K4 | Resistor_SMD:R_0805_2012Metric | R3, R19, R20, R21, R22, R23, R24, R25, R26 |
| 7 | 4K7 | Resistor_SMD:R_0805_2012Metric | R8, R10, R12, R13, R15, R33, R34 |
| 6 | 49R9 | Resistor_SMD:R_0805_2012Metric | R27, R28, R29, R30, R31, R32 |
| 5 | 1uF | Capacitor_SMD:C_0805_2012Metric | C5, C8, C10, C17, C18 |
| 4 | MountingHole_Pad | MountingHole:MountingHole_3mm_Pad_Via | H1, H2, H3, H4 |
| 4 | TestPoint | Connector_Wire:SolderWirePad_1x01_SMD_1x2mm | TP1, TP2, TP3, TP4 |
| 3 | 2K4 | Resistor_SMD:R_0805_2012Metric | R1, R7, R9 |
| 2 | 100K | Resistor_SMD:R_0805_2012Metric | R5, R6 |
| 2 | 13pF | Capacitor_SMD:C_0805_2012Metric | C29, C30 |
| 2 | 15pF | Capacitor_SMD:C_0805_2012Metric | C13, C14 |
| 2 | 1M | Resistor_SMD:R_0805_2012Metric | R4, R18 |
| 2 | 22nF | Capacitor_SMD:C_0805_2012Metric | C7, C23 |
| 2 | 22pF | Capacitor_SMD:C_0805_2012Metric | C11, C12 |
| 2 | 3.3uF/16V | Capacitor_THT:CP_Radial_D4.0mm_P2.00mm | C31, C32 |
| 2 | Polyfuse | Fuse:Fuse_Littelfuse_395Series | F1, F2 |
| 1 | 10K | Resistor_SMD:R_0805_2012Metric | R2 |
| 1 | 10uF/16V | Capacitor_THT:CP_Radial_D5.0mm_P2.00mm | C33 |
| 1 | 120 | Resistor_SMD:R_0805_2012Metric | R14 |
| 1 | 120R | Inductor_SMD:L_0805_2012Metric | FB1 |
| 1 | 12K | Resistor_SMD:R_0805_2012Metric | R16 |
| 1 | 1N4148W | Diode_SMD:D_SOD-123 | D6 |
| 1 | 1N5822 | Diode_THT:D_DO-201AD_P12.70mm_Horizontal | D1 |
| 1 | 1uH/250mA | Inductor_SMD:L_0805_2012Metric | L2 |
| 1 | 25MHz | Crystal:Crystal_HC49-U_Vertical | Y3 |
| 1 | 270uF/35V | Capacitor_THT:CP_Radial_D8.0mm_P5.00mm | C3 |
| 1 | 300 | Resistor_SMD:R_0805_2012Metric | R17 |
| 1 | 32.768KHz | Crystal:Crystal_SMD_SeikoEpson_MC156-4Pin_7.1x2.5mm_HandSoldering | Y2 |
| 1 | 470uF/50V | Capacitor_THT:CP_Radial_D10.0mm_P7.50mm | C1 |
| 1 | 47uH | Inductor_SMD:L_12x12mm_H4.5mm | L1 |
| 1 | 56K | Resistor_SMD:R_0805_2012Metric | R11 |
| 1 | 74HC14 | Package_DIP:DIP-14_W7.62mm_SMDSocket_SmallPads | U4 |
| 1 | 8MHz | Crystal:Crystal_HC49-U_Vertical | Y1 |
| 1 | 8P8C_LED_Shielded | Connector_RJ:RJ45_Cetus_J1B1211CCD_Horizontal | J5 |
| 1 | BOOT MODE | Connector_PinHeader_2.54mm:PinHeader_2x03_P2.54mm_Vertical | J2 |
| 1 | LM2596S-5 | Package_TO_SOT_SMD:TO-263-5_TabPin3 | U1 |
| 1 | MAX485E | Package_DIP:DIP-8_W7.62mm_SMDSocket_SmallPads | U5 |
| 1 | Modbus-485 | TerminalBlock_Phoenix:TerminalBlock_Phoenix_PT-1,5-3-5.0-H_1x03_P5.00mm_Horizontal | J4 |
| 1 | PWR-IN | TerminalBlock_Phoenix:TerminalBlock_Phoenix_PT-1,5-2-5.0-H_1x02_P5.00mm_Horizontal | J1 |
| 1 | RT9193-33GB | Package_TO_SOT_SMD:SOT94P279X129-5N | U2 |
| 1 | SM712_SOT23 | Package_TO_SOT_SMD:SOT-23 | D7 |
| 1 | SRV05-4 | Package_TO_SOT_SMD:SOT-23-6 | U7 |
| 1 | ST-LINK PROGRAMMER | Connector_PinHeader_2.54mm:PinHeader_1x04_P2.54mm_Vertical | J3 |
| 1 | STM32F103C8Tx | Package_QFP:LQFP-48_7x7mm_P0.5mm | U3 |
| 1 | SW_Push | Button_Switch_SMD:SW_SPST_CK_RS282G05A3 | SW1 |
| 1 | W5100 | Package_QFP:LQFP-80_10x10mm_P0.4mm | U6 |
/Oxygen%20Monitoring%20(W5500).kicad_pcb.jpg?size=s&soon)
mosyrf/Oxygen-Monitoring-System
This was my second year project as an electrical engineering student, and it was quite difficult because it used an STM32 controller, which I was not familiar with.
mosyrf/Oxygen-Monitoring-System
This was my second year project as an electrical engineering student, and it was quite difficult because it used an STM32 controller, which I was not familiar with.
jibonaronno/documentsA
It is required to change settings using SCLManager.exe when required for new setup.
havrak/UAV-project
Building a UAV as part of my final year on high school, now my hobby project
ProbablyNotArtyom/Blitz
Blitz is a 68030 based homebrew computer I designed over the course of nearly 3 years, starting in late 2017.
Loic74650/ioBoard
A relay (and more!) board with Ethernet connectivity and MQTT support
It measures 102.5 × 62 mm and has 2 copper layers, 1.6 mm thick.
121 parts, built around the MAX485ED, LM2596S-5.0, 74HC14 and RT9193-33GB. The full list of its parts is on this page, with links to each part's symbol and footprint where PCBKit's library has them.
From the mosyrf/Oxygen-Monitoring-System repository on GitHub, at the commit this page was made from: the board is PCB Design/Oxygen Monitoring (W5100)/Oxygen Monitoring.kicad_pcb and its schematic PCB Design/Oxygen Monitoring (W5100)/Oxygen Monitoring.kicad_sch. PCBKit opens the board in the browser, with nothing to install.
Its repository states no licence, so its author keeps all rights: ask mosyrf before reusing the design.