

Stroom shield
- Size
- 70 × 82.5 mm
- Copper layers
- 2
- Thickness
- 1.6 mm
- Parts
- 60
- Nets
- 186
- Pads
- 387
- Tracks, vias
- 0, 0
- Routed
- Not yet
- KiCad
- KiCad 5 (file 20171130)
- Created
- 13 Sep 2023
- Updated
- 11 Jun 2025
Overview
Stroom shield is an open-source printed circuit board by VHLZonnebootteam, from the VHLZonnebootteam/Telemetrie repository on GitHub. It is a 2-layer board of 70 × 82.5 mm with 60 parts on 186 nets.
It is built around the 74LVC1G14DBVR, MC33269ST-3.3 and W5100, with the PN2222A among its other parts. Its parts include 16 capacitors, 8 resistors, 6 ICs, 5 diodes and 3 inductors.
Main components
474LVC1G14DBVR
SOT-23-5SOT-23-5 Logic Gates ROHSSlkorLogic GatesMC33269ST-3.3
SOT-223-4-40℃~+125℃@(Ta) 1 1V@(500mA) 20V 3.3V 5.5mA 55dB@(120Hz) 800mA Fixed Over Temperature Protection、Short Circuit Protection Positive SOT-223-4 Voltage Regulators - Linear, Low Drop Out (LDO) Regulators ROHSonsemiVoltage Regulators - Linear, Low Drop Out (LDO) RegulatorsW5100
--40℃~+85℃ 1.2mm 1dBi 3 40mm 40mm 50Ω 83.5MHz - Antennas ROHSPulse ElecAntennasPN2222A
TO-92-3-55℃~+150℃ 1 NPN 1A 300MHz 300mV 40V 625mW NPN TO-92-3 Bipolar (BJT) ROHSNTE ElectronicsBipolar (BJT)
Parts
60| Qty | Value | Footprint | References |
|---|---|---|---|
| 6 | 100n | Resistor_SMD:R_0603_1608Metric_Pad1.05x0.95mm_HandSolder | C1, C2, C3, C6, C7, C13 |
| 3 | 1K | Resistor_SMD:R_0603_1608Metric_Pad1.05x0.95mm_HandSolder | R6, R7, R8 |
| 3 | 470uf | Capacitor_THT:CP_Radial_D5.0mm_P2.50mm | C9, C11, C12 |
| 3 | BLM21 | Shield_Eth06-REV3:WUERTH-ELEKTRONIK_0805 | L1, L2, L3 |
| 3 | Yellow | LED_SMD:LED_0603_1608Metric_Pad1.05x0.95mm_HandSolder | LINK1, RX1, TX1 |
| 2 | 10k | Resistor_SMD:R_0603_1608Metric_Pad1.05x0.95mm_HandSolder | R1, R4 |
| 2 | 1N5401 | Diode_THT:D_DO-201AD_P15.24mm_Horizontal | D4, D5 |
| 2 | 1k | Shield_Eth06-REV3:RESISTOR-DIL_CAY16 | RN1, RN3 |
| 2 | 22p | Resistor_SMD:R_0603_1608Metric_Pad1.05x0.95mm_HandSolder | C4, C5 |
| 2 | 47u | Shield_Eth06-REV3:RCL_PANASONIC_D | C15, C16 |
| 2 | 8x1F-H8.5-L14.5mm | Shield_Eth06-REV3:SMARTPRJ_1X08 | JLOW1, POWER1 |
| 2 | Jumper_NC_Dual | Jumper:SolderJumper-3_P1.3mm_Open_Pad1.0x1.5mm | JP1, JP2 |
| 1 | 100n | Shield_Eth06-REV3:SMARTPRJ_C0603-ROUND | C10 |
| 1 | 10V out | TerminalBlock_WAGO:TerminalBlock_WAGO_236-302_1x02_P10.00mm_45Degree | J2 |
| 1 | 10u | Resistor_SMD:R_0603_1608Metric_Pad1.05x0.95mm_HandSolder | C8 |
| 1 | 10uf | Capacitor_SMD:C_0603_1608Metric_Pad1.05x0.95mm_HandSolder | C14 |
| 1 | 10x1F-H8.5-L14.5mm | Shield_Eth06-REV3:SMARTPRJ_1X10 | JHIGH1 |
| 1 | 12V in | TerminalBlock_WAGO:TerminalBlock_WAGO_236-202_1x02_P7.50mm_45Degree | J1 |
| 1 | 12k 1% | Resistor_SMD:R_0603_1608Metric_Pad1.05x0.95mm_HandSolder | R3 |
| 1 | 1M | Resistor_SMD:R_0603_1608Metric_Pad1.05x0.95mm_HandSolder | R5 |
| 1 | 25MHz SMD | Shield_Eth06-REV3:CRYSTAL_HC49UP | Q1 |
| 1 | 300R 1% | Resistor_SMD:R_0603_1608Metric_Pad1.05x0.95mm_HandSolder | R2 |
| 1 | 3x2F-H11 | Shield_Eth06-REV3:SMARTPRJ_2X03 | ICSP1 |
| 1 | 49R9 | Shield_Eth06-REV3:RESISTOR-DIL_CAY16 | RN2 |
| 1 | 6x1F-H8.5-L14.5mm | Shield_Eth06-REV3:PINHEAD_1X06 | JANALOG1 |
| 1 | 74LVC1G14DBV | Shield_Eth06-REV3:74XX-LITTLE-DE_SOT23-5 | IC1 |
| 1 | Fuse | stroom_shield:fuse_holder | F1 |
| 1 | Green | LED_SMD:LED_0603_1608Metric_Pad1.05x0.95mm_HandSolder | ON1 |
| 1 | Green | Shield_Eth06-REV3:LED_CHIPLED_0805 | 100M1 |
| 1 | INIT | LED_SMD:LED_0603_1608Metric_Pad1.05x0.95mm_HandSolder | D2 |
| 1 | MC33269ST-3.3 | Shield_Eth06-REV3:LINEAR_SOT223 | IC3 |
| 1 | NUCLEO-F446RE | stroom_shield:MODULE_NUCLEO-F446RE | U3 |
| 1 | OK | LED_SMD:LED_0603_1608Metric_Pad1.05x0.95mm_HandSolder | D1 |
| 1 | PN2222A | Package_TO_SOT_THT:TO-92_Inline | Q2 |
| 1 | POE-RJ45 | Shield_Eth06-REV3:SMARTPRJ_POE-RJ45 | U$1 |
| 1 | PWR | LED_SMD:LED_0603_1608Metric_Pad1.05x0.95mm_HandSolder | D3 |
| 1 | RS485_module | stroom_shield:RS485_module | U2 |
| 1 | W5100 | Package_QFP:LQFP-80_10x10mm_P0.4mm | IC2 |
| 1 | buck_converter | stroom_shield:buck_converter | U1 |
| 1 | ~ | Shield_Eth06-REV3:JUMPER_SJ | INT1 |
More from VHLZonnebootteam/Telemetrie
1- 2 layers70.1 × 82.5 mm

Similar boards
- 2 layers165 × 85 mm

Power Distribution V1.1
sOrzada/STASIS_Exposure_Hardware
This is the repository for the exposition hardware of the STASIS project.
63 partsCERN-OHL-W-2.0 - 4 layers214 × 170 mm

.C68
ProbablyNotArtyom/Blitz
Blitz is a 68030 based homebrew computer I designed over the course of nearly 3 years, starting in late 2017.
185 parts51GPL-2.0 - 2 layers50 × 50 mm

- 4 layers70 × 143 mm

IoBoard
Loic74650/ioBoard
A relay (and more!) board with Ethernet connectivity and MQTT support
206 parts3GPL-3.0 - 2 layers86.9 × 51.8 mm

- 2 layers102.5 × 62 mm

Oxygen Monitoring
mosyrf/Oxygen-Monitoring-System
This was my second year project as an electrical engineering student, and it was quite difficult because it used an STM32 controller, which I was not familiar with.
121 parts - 2 layers233.4 × 280 mm

- 2 layers236.7 × 149.7 mm

ControllinoA
jibonaronno/documentsA
It is required to change settings using SCLManager.exe when required for new setup.
265 parts4
Questions
How big is the Stroom shield PCB?
It measures 70 × 82.5 mm and has 2 copper layers, 1.6 mm thick.
What parts does the Stroom shield use?
60 parts, built around the 74LVC1G14DBVR, MC33269ST-3.3, W5100 and PN2222A. The full list of its parts is on this page, with links to each part's symbol and footprint where PCBKit's library has them.
Where can I download the Stroom shield KiCad files?
From the VHLZonnebootteam/Telemetrie repository on GitHub, at the commit this page was made from: the board is pcbs/stroom_shield/stroom_shield.kicad_pcb. PCBKit opens the board in the browser, with nothing to install.
Can I use the Stroom shield design in my own project?
Its repository states no licence, so its author keeps all rights: ask VHLZonnebootteam before reusing the design.