Skip to the content
2 layers62.9 × 32.4 mmVolume AlpsRK16814MG, the printed circuit board in 3D

Volume AlpsRK16814MG

mithat/Volume-AlpsRK16814MG6

Alps RK16814MG motorized potentiometer with H-bridge motor drive.

Size
62.9 × 32.4 mm
Copper layers
2
Thickness
1.6 mm
Parts
12
Nets
24
Pads
58
Tracks, vias
176, 34
Pours
4
Routed
Yes
KiCad
KiCad 5 (file 20171130)
Created
22 Mar 2015
Updated
10 Nov 2021

Overview

Volume AlpsRK16814MG is an open-source printed circuit board by mithat, from the mithat/Volume-AlpsRK16814MG repository on GitHub. It is a 2-layer board of 62.9 × 32.4 mm with 12 parts on 24 nets, routed with 176 tracks and 34 vias.

It is built around the SN754410NE. Its parts include 6 connectors, 2 capacitors and 1 IC.

Main components

1

README

readme.md

Volume-AlpsRK16814MG

Because volume control is free and for the people.™

Description

KiCad 5.0 design files for a PCB that integrates an Alps RK16814MG motorized potentiometer with an H bridge to drive the motor using logic-level signals.

Inputs and outputs

NameFunction
VOL_UPLogical input to rotate the potentiometer clockwise.
VOL_DOWNLogical input to rotate the potentiometer counter-clockwise.
V_MOTPower for motor drive. Nominally 6 VDC, but see comments below.
+5VDPower for logic circuits. 5 VDC.
DGNDGround for digital (logic) circuits.
CHASSIS GROUNDGround for potentiometer case. Also labeled as C.G. on top side of PCB.
A_TOPPotentiometer A input
A_WIPERPotentiometer A output
AB_COMMONPotentiometer A and B's common (typically connects to signal ground)
B_TOPPotentiometer B input
B_WIPERPotentiometer A output
C_TOPPotentiometer C input
C_WIPERPotentiometer C output
CD_COMMONPotentiometer C and D's common (typically connects to signal ground)
D_TOPPotentiometer D input
D_WIPERPotentiometer D output

Power

There are two power inputs to the board, one for the 5 VDC logic (+5VD) and the other to drive the potentiometer's motor (V_MOT). The board has a jumper (J1) that when installed will connect V_MOT to +5VD---making it possible to operate the module from just one +5VDC power source, albeit with a couple caveats.

First, owing to the voltage drop across the Darlington H-bridge, the optimum voltage for V_MOT is 6 VDC. When V_MOT is 5 VDC, the resulting voltage delivered to the Alps RK16814MG's motor falls below Alps' specified minimum. However, the motor seems to have no problem operating at this lower than specified voltage. Second, the motor's maximum specified current consumption is 150 mA. This is beyond the capacity of, for example, the on-board regulators found on many Arduinos. Therefore, if you opt to jumper J1, you may have to use an external logic supply if you are using something like an Arduino for control.

Grounding

The logic supply ground is completely isolated from other grounds. For the love of all that is good, don't mix your logic and audio grounds. Connect the logic and audio grounds at one point only and as close to the main power supplies as possible.

It is assumed the case of the potentiometer is grounded through the chassis. A ground pin labeled C.G. is provided if this is not the case. This connection should not be used as a signal ground but rather only to provide a shielding connection for the potentiometer's case.

The potentiometer internally connects the "ground" sides of both elements of each gang. These are brought out as independent commons (AB_COMMON and CD_COMMON). Typically, AB_COMMON and CD_COMMON will be connected to signal ground.

Use

While it's possible to use the Volume-AlpsRK16814MG PCB for applications other than volume control, we assume that you will be using it for volume control.

The Alps RK16814MG consists of two gangs of dual potentiometers. Refer to the table above for the PCB's I/O corresponding to these.

For regular (non-differential) stereo use, you have the option of using both elements of one gang (e.g., A and B) or one element from from each gang (e.g., A and C).

For differential stereo control, both elements on both gangs will be required.

To rotate the potentiometer CW (i.e., up), apply a logical 1 to VOL_UP and a logical 0 to VOL_DOWN. To rotate the potentiometer CCW (i.e., down), apply a logical 1 to VOL_DOWN and a logical 0 to VOL_UP. No harm will come if a logical 1 is applied to both VOL_UP and VOL_DOWN simultaneously.

License

CERN Open Hardware License v1.2

Copyright

Copyright (C) 2015 Mithat Konar.

Parts

12
QtyValueFootprintReferences
1100nVolume-AlpsRK16814MG:C_4.0_2.5_2.5_0.5C1
11uVolume-AlpsRK16814MG:C_4.0_2.5_2.5_0.5C2
1AB I/OVolume-AlpsRK16814MG:TE_282834-5P1
1CD I/OVolume-AlpsRK16814MG:TE_282834-5P2
1CTRLVolume-AlpsRK16814MG:TE_282834-2P4
1GNDVolume-AlpsRK16814MG:AVA-20gaP5
1PWRVolume-AlpsRK16814MG:TE_282834-3P3
1PWR_BRVolume-AlpsRK16814MG:SIL-2J1
1REFoshw-logo-notext-100mil-FSilkLOGO2
1REFoshw-logo-250mil-FSilkLOGO1
1RK16814MGVolume-AlpsRK16814MG:ALPS_RK16814MGRV1
1SN754410Volume-AlpsRK16814MG:DIP-16_AriesC84_eU1

Similar boards

  • 2 layers94.8 × 47.8 mmMouse v2, the printed circuit board in 3D

    Mouse v2

    lowj/fish-mouse

    Small Robot for maze navigation (Micromouse)

    77 parts5
  • 2 layers69.9 × 52.6 mmArduiBodet, the printed circuit board in 3D

    ArduiBodet

    PatriceG/ArduiBodet

    Horloge mère pour Horloge de type Bodet pilotée par Arduino

    22 parts5GPL-3.0
  • 2 layers162.6 × 123.2 mmTo print, the printed circuit board in 3D

    To print

    anorimaki/selfbalancing-robot

    A buck converter to generate the 5V power rail would have been a better choice because it would be more efficient (extending battery life) and eliminate the need of a second battery (the circuit could be plugged with…

    124 parts2
  • 2 layers111.8 × 95.3 mmSplitflap, the printed circuit board in 3D

    Splitflap

    dylanmsu/Splitflap_Display

    software to drive a public split flap display

    38 parts1GPL-3.0
  • 2 layers80.1 × 85.2 mmOmni wheel, the printed circuit board in 3D

    Omni wheel

    kashishkebab9/omni-mapper

    Omni-Wheeled Robot with custom PCB All Mechanical Assemblies, PCBs, Firmware, and Software designed, architected and programmed by Kashish Garg

    52 parts1MIT
  • 2 layers72 × 47 mmMtdr S, the printed circuit board in 3D

    Mtdr S

    KeioRoboticsAssociation/F-3RC_MD

    Motor drivers for F^3RC.

    14 parts1
  • 2 layers99 × 99 mmDue behavior breakout, the printed circuit board in 3D

    Due behavior breakout

    losonczylab/Hardware

    Includes AutoDesk Inventor projects used for lab rigs and other miscellaneous CAD files.

    109 parts1GPL-3.0
  • 2 layers47.6 × 90.2 mmRoben, the printed circuit board in 3D

    Roben

    akornsys-rdi/robgednaut

    Robust and easy-to-use introduction-to-robotics platform

    92 parts

Questions

How big is the Volume AlpsRK16814MG PCB?

It measures 62.9 × 32.4 mm and has 2 copper layers, 1.6 mm thick.

What parts does the Volume AlpsRK16814MG use?

12 parts, built around the SN754410NE. The full list of its parts is on this page, with links to each part's symbol and footprint where PCBKit's library has them.

Where can I download the Volume AlpsRK16814MG KiCad files?

From the mithat/Volume-AlpsRK16814MG repository on GitHub, at the commit this page was made from: the board is Volume-AlpsRK16814MG.kicad_pcb. PCBKit opens the board in the browser, with nothing to install.

Can I use the Volume AlpsRK16814MG design in my own project?

Its repository states no licence, so its author keeps all rights: ask mithat before reusing the design.