Skip to the content
2 layers69.9 × 52.6 mmArduiBodet, the printed circuit board in 3D

Horloge mère pour Horloge de type Bodet pilotée par Arduino

Size
69.9 × 52.6 mm
Copper layers
2
Thickness
1.6 mm
Parts
22
Nets
42
Pads
99
Tracks, vias
223, 14
Routed
Yes
KiCad
KiCad 4
Created
26 Apr 2015
Updated
21 May 2025

Overview

ArduiBodet is an open-source printed circuit board by PatriceG, from the PatriceG/ArduiBodet repository on GitHub, published under the GPL-3.0 licence. It is a 2-layer board of 69.9 × 52.6 mm with 22 parts on 42 nets, routed with 223 tracks and 14 vias.

It is built around the ATMEGA328-PU, SN754410NE and LM7805CT. Its parts include 5 capacitors, 4 connectors, 3 resistors, 3 ICs and 2 switches. It belongs with the AVR (ATmega, ATtiny) boards of this library.

Main components

3

README

README.md

ArduiBodet

Horloge mère pour Horloge de type Bodet 1/2 Minute pilotée par Arduino

Ce code nécessite les librairies suivantes: -DS3231 : http://m5.img.dxcdn.com/CDDriver/CD/sku.222910.rar -Low-Power: [https://github.com/rocketscream/Low-Power] (https://github.com/rocketscream/Low-Power)

L'IDE utilisé est AtmelStudio + VisualMicro mais le code est compatible avec l'IDE Arduino.

Les détails de la construction de l'horloge mère sont donnés ici: http://breizhmakers.over-blog.com/tag/horlogebodet/

Les objectifs fixés sont:

  • Faible coût
  • Alimentation 9V (nécessaire pour piloter l'horloge)
  • Application automatique des changements d'heure.
  • Très bonne stabilité de l'horloge (2 ppm soit environ 1 minute/an)
  • Interrupteur Marche/Arrêt
  • Interrupteur de mise en mode avance rapide pour mise à l'heure.

Comment Flasher le Firmware

La plupart des ATMega328 sont livrés configurés pour fonctionner avec un quartz externe à 16MHz.

Avant de pouvoir flasher le firmware il faut donc installer l'ATMega sur une Breadboard en y câblant un quartz 16MHz et ses condensateurs associés, et y brancher le programmateur (j'utilise un USBAsp).

J'ai ensuite suivi cette doc avec un IDE Arduino 1.8.18, mais cela fonctionne aussi avec l'IDE Arduino 2.x, pour configurer l'Arduino en mode horloge interne 1MHz (ou 8MHz, ça fonctionne aussi).

Une fois les définitions de Board MiniCore installées et choisi ATMega328 on a accès à tout un tas de settings, dont le mode de fonctionnement de l'horloge. Il reste ensuite à cliquer sur "Graver la séquence d'initialisation" pour flasher cette config de fuses (avec le programmateur choisi. J'utilise un USBAsp).

Il est ensuite conseillé de flasher le sketch Blink et de vérifier que la pin correspondant à D13 clignotte bien à 1 Hz

On peut alors flasher le sketch de l'Horloge.

Parts

22
QtyValueFootprintReferences
4myLib:MountingHole_1.5mm, , ,
1100 nFMyLib:C_Rect_L7_W2.5_P2.5C2
11000 uFCapacitors_Elko_ThroughHole:Elko_vert_20x10mm_RM2.5C4
1100nFMyLib:C_Rect_L7_W2.5_P2.5C1
1100nFCapacitors_ThroughHole:C_Rect_L4_W2.5_P2.5C3
122KResistors_ThroughHole:Resistor_Horizontal_RM10mmR1
1330nFMyLib:C_Rect_L7_W2.5_P2.5C5
147Resistors_ThroughHole:Resistor_Vertical_RM5mmR2
1470Resistors_ThroughHole:Resistor_Horizontal_RM10mmR3
1ATMEGA328-PHousings_DIP:DIP-28__300IC1
1BARREL_JACKmyLib:BARREL_JACK_FRCON1
1DS3231_Breakout_ConnectorPin_Headers:Pin_Header_Straight_1x06P2
1ICSP_10_PINPin_Headers:Pin_Header_Straight_2x05P1
1LEDLEDs:LED-5MMD1
1LM7805CTPower_Integrations:TO-220U1
1Moteur HorlogePin_Headers:Pin_Header_Straight_1x02P3
1SN754410Housings_DIP:DIP-16__300IC2
1SWITCH_INVPin_Headers:Pin_Header_Straight_1x03SW1
1Switch_DPSTmyLib:Pin_Header_Straight_2x03_for_SPDT_switchSW2

Similar boards

  • 2 layers169.3 × 128 mmPSU PCB, the printed circuit board in 3D

    PSU PCB

    ThomasVDD/SmartSupply

    SmartSupply is a digital battery powered lab powersupply. It is Arduino compatible and can be controlled via PC over USB.

    134 parts96
  • 2 layers100.1 × 70.1 mmSlowRGB, the printed circuit board in 3D

    SlowRGB

    dileepvr/slowRGB

    Fancy nightlight

    34 partsGPL-3.0
  • 2 layers150.5 × 90.8 mmLoad v2, the printed circuit board in 3D

    Load v2

    sangseu/kicad

    118 parts
  • 2 layers62.9 × 32.4 mmVolume AlpsRK16814MG, the printed circuit board in 3D

    Volume AlpsRK16814MG

    mithat/Volume-AlpsRK16814MG

    Alps RK16814MG motorized potentiometer with H-bridge motor drive.

    12 parts6
  • 2 layers94.8 × 47.8 mmMouse v2, the printed circuit board in 3D

    Mouse v2

    lowj/fish-mouse

    Small Robot for maze navigation (Micromouse)

    77 parts5
  • 2 layers162.6 × 123.2 mmTo print, the printed circuit board in 3D

    To print

    anorimaki/selfbalancing-robot

    A buck converter to generate the 5V power rail would have been a better choice because it would be more efficient (extending battery life) and eliminate the need of a second battery (the circuit could be plugged with…

    124 parts2
  • 2 layers111.8 × 95.3 mmSplitflap, the printed circuit board in 3D

    Splitflap

    dylanmsu/Splitflap_Display

    software to drive a public split flap display

    38 parts1GPL-3.0
  • 2 layers80.1 × 85.2 mmOmni wheel, the printed circuit board in 3D

    Omni wheel

    kashishkebab9/omni-mapper

    Omni-Wheeled Robot with custom PCB All Mechanical Assemblies, PCBs, Firmware, and Software designed, architected and programmed by Kashish Garg

    52 parts1MIT

Questions

How big is the ArduiBodet PCB?

It measures 69.9 × 52.6 mm and has 2 copper layers, 1.6 mm thick.

What parts does the ArduiBodet use?

22 parts, built around the ATMEGA328-PU, SN754410NE and LM7805CT. The full list of its parts is on this page, with links to each part's symbol and footprint where PCBKit's library has them.

Where can I download the ArduiBodet KiCad files?

From the PatriceG/ArduiBodet repository on GitHub, at the commit this page was made from: the board is doc/Kicad/ArduiBodet.kicad_pcb. PCBKit opens the board in the browser, with nothing to install.

Can I use the ArduiBodet design in my own project?

Its repository publishes it under the GPL-3.0 licence: you may reuse it on that licence's terms (keep the author's notice, and for a copyleft licence share your changes alike).