
JBclone soldering station
Minu-IU3IRR/JBclone-soldering-station
Multi channel DIY soldering station with JBC tip support

JTAG probe using the ESP8266
Esp8266-probe is an open-source printed circuit board by mgottschlag, from the mgottschlag/esp8266-probe repository on GitHub. It is a 2-layer board of 70 × 38 mm with 63 parts on 56 nets, routed with 436 tracks and 87 vias.
It is built around the ESP-12E, LD1117DT33 and BC817, with the NX2301P among its other parts. Its parts include 31 resistors, 11 capacitors, 6 ICs, 4 transistors and 3 connectors. It belongs with the sensors and measurement and interfaces and adapters boards and the ESP8266 boards of this library.
This repository contains a PCB design for a WIFI JTAG probe using the ESP-12 ESP8266 module. The probe is designed to be compatible with blackmagic-espidf. The JTAG signals (+UART) are connected as follows to ESP8266 GPIOs:
| JTAG Signal | GPIO |
|---|---|
| TXD | 1 |
| RXD | 3 |
| TMS/SWDIO | 4 |
| TCK/SWCLK | 5 |
| SRST | 12 |
| TDI | 13 |
| TDO | 14 |
In addition, the 10-pin connector provides 5V and 3.3V supplies. The PCB is provided with power via USB and 3.3V is provided by a cheap 1117 linear regulator.
The design is licensed under the CERN Open Hardware Licence Version 2 - Permissive.
| Qty | Value | Footprint | References |
|---|---|---|---|
| 10 | 100 | Resistor_SMD:R_0603_1608Metric | R9, R10, R11, R12, R14, R15, R16, R25, R28, R29 |
| 8 | 0.1uF | Capacitor_SMD:C_0603_1608Metric | C4, C5, C6, C7, C8, C9, C10, C11 |
| 6 | 12K | Resistor_SMD:R_0603_1608Metric | R3, R4, R5, R6, R8, R26 |
| 6 | DNP | Resistor_SMD:R_0603_1608Metric | R17, R18, R19, R20, R21, R23 |
| 4 | 74LVC2T45DCT | Package_SO:VSSOP-8_3.0x3.0mm_P0.65mm | U3, U4, U5, U6 |
| 3 | 10K | Resistor_SMD:R_0603_1608Metric | R22, R24, R30 |
| 2 | 10uF | Capacitor_Tantalum_SMD:CP_EIA-6032-20_AVX-F_Pad2.25x2.35mm_HandSolder | C1, C2 |
| 2 | 5.1K | Resistor_SMD:R_0603_1608Metric | R1, R2 |
| 2 | BC817 | Package_TO_SOT_SMD:SOT-23 | Q1, Q3 |
| 2 | MountingHole | MountingHole:MountingHole_3.2mm_M3 | H3, H4 |
| 2 | MountingHole_Pad | MountingHole:MountingHole_3.2mm_M3_Pad | H1, H2 |
| 2 | NX2301P | Package_TO_SOT_SMD:SOT-23 | Q2, Q4 |
| 1 | 100K | Resistor_SMD:R_0603_1608Metric | R31 |
| 1 | 100uF | Capacitor_THT:CP_Radial_D6.3mm_P2.50mm | C3 |
| 1 | 1K | Resistor_SMD:R_0603_1608Metric | R13 |
| 1 | 470 | Resistor_SMD:R_0603_1608Metric | R7 |
| 1 | 47K | Resistor_SMD:R_0603_1608Metric | R27 |
| 1 | Debug | Connector_PinHeader_2.54mm:PinHeader_1x03_P2.54mm_Vertical | J2 |
| 1 | ESP-12E | RF_Module:ESP-12E | U2 |
| 1 | Flash | Button_Switch_SMD:SW_SPST_PTS810 | SW2 |
| 1 | KicadLogo | Symbol:KiCad-Logo2_5mm_SilkScreen | H6 |
| 1 | LD1117DT33 | Package_TO_SOT_SMD:TO-252-2 | U1 |
| 1 | OSHWLogo | Symbol:OSHW-Logo_5.7x6mm_SilkScreen | H5 |
| 1 | Reset | Button_Switch_SMD:SW_SPST_PTS810 | SW1 |
| 1 | Target | Connector_IDC:IDC-Header_2x05_P2.54mm_Vertical | J3 |
| 1 | USB_C_Receptacle_USB2.0 | Connector_USB:USB_C_Receptacle_HRO_TYPE-C-31-M-12 | J1 |

Minu-IU3IRR/JBclone-soldering-station
Multi channel DIY soldering station with JBC tip support

aspdac-submission-pcb-layout/PCB-Layout-Framework
This repository has been prepared from the original. Some care has been taken to remove the names of the authors.



Miceuz/paper-wifi
Low power E-paper display devboard with WiFi and BLE connectivity. Open source hardware.



It measures 70 × 38 mm and has 2 copper layers, 1.6 mm thick.
63 parts, built around the ESP-12E, LD1117DT33, BC817 and NX2301P. The full list of its parts is on this page, with links to each part's symbol and footprint where PCBKit's library has them.
From the mgottschlag/esp8266-probe repository on GitHub, at the commit this page was made from: the board is hardware/esp8266-probe.kicad_pcb and its schematic hardware/esp8266-probe.kicad_sch. PCBKit opens the board in the browser, with nothing to install.
Its repository states no licence, so its author keeps all rights: ask mgottschlag before reusing the design.