Skip to the content
2 layers180 × 70 mmBms, the printed circuit board in 3D

A battery management system (BMS) for small vehicles mainly 36V and 48V (golf carts & quads).

Size
180 × 70 mm
Copper layers
2
Thickness
1.6 mm
Parts
225
Nets
171
Pads
670
Tracks, vias
1,833, 164
Pours
8
Routed
Yes
KiCad
KiCad 3
Created
21 Nov 2015
Updated
9 Nov 2018

Overview

Bms is an open-source printed circuit board by mandraga, from the mandraga/SombreroBms repository on GitHub. It is a 2-layer board of 180 × 70 mm with 225 parts on 171 nets, routed with 1,833 tracks and 164 vias.

It is built around the ATMEGA32M1-AU, TJA1052IT/5Y and FT232RQ, with the LM2936M-3.0, NUP2105L and 0.1UF 50V 5*11 among its other parts. Its parts include 80 resistors, 63 capacitors, 26 connectors, 15 ICs and 14 transistors. It belongs with the power boards and the AVR (ATmega, ATtiny) boards of this library.

Main components

7

README

README.md

SombreroBms

SombreroBMS could have been a battery management system board and software for small electric vehicles and conversions. Mainly 36V and 48V battery packs for golf carts. Currently an unfinished project. Reading the sensors worked and monitoring from a serial line worked. The repository has a simulation project in order to try different balancing algorithms.

Planed features:

  • Lithium phosphate battery packs.
  • Protection relay to connect to a power relays like a Gigavac 250A.
  • State of charge updated by a current sensor during the discharge.
  • Custom gauge connected with one wire + Gnd serial communication.
  • Monitoring from a laptop computer using a serial communication over USB.
  • Passive balancing (possibility for a heavy duty version for first balancing use).
  • Undervoltage events count per battery + worst value recording.
  • Powered from the battery pack.
  • 10 to 18 batteries.

The development was interrupted when I moved to Lyon in 2016. And the client switched to Orion BMS, so the target was lost and the funding shorted. However I started SombreroBMS2, simpler, safer, cheaper and easier to use. For lighter vehicles (but it will keep the same functionnality). I will add more unit testing and simulation on it (hence the switch to gitlab). Building more on software interfaces and abstraction layers and using the test driven development aproach. On the second version the client is myself :)

https://gitlab.com/arenyp/sombrerobms2 http://blog.vreemdelabs.com/

Parts

225
QtyValueFootprintReferences
3610KSM0805R1, R3, R4, R11, R19, R20, R22, R23, R33, R34, R35, R36, R37, R38, R39, R40 +20
200.1uFSM0805C1, C2, C5, C25, C26, C28, C39, C40, C42, C44, C50, C53, C54, C56, C57, C59 +4
13CONN_11pin2mmP8, P9, P10, P11, P12, P13, P14, P15, P16, P17, P18, P19, P20
120.1uF50VSM1206C16, C17, C18, C19, C20, C21, C30, C31, C32, C33, C34, C35
121RPOW_RESR27, R28, R29, R30, R31, R32, R50, R51, R52, R53, R54, R55
12NTD5867DPAK2Q2, Q3, Q4, Q5, Q6, Q7, Q8, Q9, Q10, Q11, Q12, Q13
90RSM0805R12, R13, R14, R16, R18, R46, R47, R69, R70
922pFSM0805C3, C4, C9, C10, C11, C12, C13, C14, C15
71KSM0805R10, R15, R17, R21, R24, R25, R75
61uFSM0805C27, C29, C41, C43, C45, C55
6CONN_11pinP1, P2, P3, P4, P5, P6
5LEDLED-0805D1, D2, D3, D9, D10
40.1uF100VSM1206C22, C23, C36, C37
34,7KSM0805R74, R76, R77
34.7KSM0805R5, R6, R7
3FILTERFILTER_NFE61HT102FFB2, FB3, FB4
3OPTOOPTO_CMSU1, U2, U11
20RSM1206R26, R49
210uF100VSMDHD/VFC24, C38
24,7kSM0805R79, R80
24.7kSM0805R8, R9
260nFSM0805C62, C63
2AD7280ALQFP48U3, U4
2BC850SOT23EBCQ1, Q14
2DIODEDO_214AAD7, D8
2EMI_FILTER2EMI_FILTER_NFE61HTFI1, FI2
2FILTERc_0805FB1, FB5
2THERMISTORSM0805TH1, TH2
2TSTTestPP23, P24
2ZENER 29VDO-214AA(SMB)D4, D5
10.1uF60VSM0805C58
10.22uF100VSM1206C49
1100KSM0805R72
110KSM1206R78
110nFSM0805C52
110uF20VSM1206POLC51
11MSM0805R2
12.2uF100VSM1206C48
122uF16VSMDHD/VFC47
133µHinductor-coilcraft-DS1608L1
1374KSM0805R73
13uFSM1206C61
14,7nFSM0805C60
1ATMEGA32M1-ATQFP32IC1
1CONN_3X2pin_array_3x2P7
1CONN_4PIN_ARRAY_2X2CAN BUS
1CRYSTALHC-18UVX1
1Charger_GND 12V SHUTDWNbornier3K1
1FT232RQQFN32-5x5U8
1GAUGEbornier2P25
1HRS1KREL_PE014U7
1INA197sot323-5U6
1LM2936SOT223U14
1LT3990-3.3MSOP16EU5
1M45PE16SO8WU10
1NUP2105LSOT23U13
1REL NC VBATbornier3K2
1RESETCMSSWSW1
1SHUNT-1pin2mmP21
1SI8422NSOP8U9
1SPEAKERbuzzerSP1
1SWITCH_INVMICROSWITCH_SPSTON OFF
1TJA1052ISO16WU12
1USB-MINI-BMICRO_USB_BCON1
1VBAT1pin2mmP22
1ZENER 55VDO-214AA(SMB)D6

More from mandraga/SombreroBms

1
  • 2 layers179.5 × 67 mmBms, the printed circuit board in 3D

    Bms

    mandraga/SombreroBms

    A battery management system (BMS) for small vehicles mainly 36V and 48V (golf carts & quads).

    192 parts4

Similar boards

  • 2 layers180.9 × 110 mmSaunasteuerung ESP Home, the printed circuit board in 3D

    Saunasteuerung ESP Home

    Technolitix/Sauna-Contoller

    Standalone sauna controller running ESPHome, compatible with Home Assistant for smart temperature, timer, and lighting control.

    103 partsMIT
  • 4 layers85 × 60 mmKeithleyUpgrade, the printed circuit board in 3D

    KeithleyUpgrade

    asanza/keithley_199

    Upgrades for an old Keithley 199 multimeter

    75 parts8GPL-3.0
  • 4 layers90 × 65 mmKeithleyUpgrade, the printed circuit board in 3D

    KeithleyUpgrade

    Na55im/keithley199-upgrade

    This is an upgrade replacement for the digital control board on Keithley 199 multimeters.

    85 partsGPL-3.0
  • 2 layers68.6 × 53.3 mmH9uno, the printed circuit board in 3D

    H9uno

    c3h9dx/h9uno

    The Arduino Uno clone with a CAN bus support for the H9.

    30 parts
  • 2 layers73.3 × 66.8 mm6xUSB PowMet, the printed circuit board in 3D

    6xUSB PowMet

    aleksejm/6xUSB-Power-Meter

    6 USB port Power Meter

    97 parts7
  • 4 layers160 × 110 mmHPM6E00FULLPORTRevB, the printed circuit board in 3D

    HPM6E00FULLPORTRevB

    hpmicro/hpm_apps

    hpm apps for hpm sdk

    726 parts35BSD-3-Clause
  • 4 layers146 × 102 mmHPM6E00EVKRevC, the printed circuit board in 3D

    HPM6E00EVKRevC

    joelxue123/hpm6e00evk-ethercat-motor-bridge

    This workspace is for the HPM6E00EVK RevC EtherCAT-to-UART motor bridge.

    562 parts

Questions

How big is the Bms PCB?

It measures 180 × 70 mm and has 2 copper layers, 1.6 mm thick.

What parts does the Bms use?

225 parts, built around the ATMEGA32M1-AU, TJA1052IT/5Y, FT232RQ and LM2936M-3.0. The full list of its parts is on this page, with links to each part's symbol and footprint where PCBKit's library has them.

Where can I download the Bms KiCad files?

From the mandraga/SombreroBms repository on GitHub, at the commit this page was made from: the board is pcb_11bat_Rev1/bms.kicad_pcb. PCBKit opens the board in the browser, with nothing to install.

Can I use the Bms design in my own project?

Its repository states no licence, so its author keeps all rights: ask mandraga before reusing the design.