Skip to the content
2 layers160 × 100 mmJunior universal memory, the printed circuit board in 3D

A replica of the Junior Computer (a KIM-1 clone) published by Elektor in the 80's

Size
160 × 100 mm
Copper layers
2
Thickness
1.6 mm
Parts
38
Nets
119
Pads
501
Tracks, vias
2,137, 73
Pours
5
Routed
Yes
KiCad
KiCad 8.0 (file 20240108)
Created
1 Oct 2020
Updated
21 Dec 2024

Overview

Junior universal memory is an open-source printed circuit board by laurent-fr, from the laurent-fr/junior_computer_replica repository on GitHub. It is a 2-layer board of 160 × 100 mm with 38 parts on 119 nets, routed with 2,137 tracks and 73 vias.

It is built around the 74LS373SC, 74LS245SC and 74LS00SC, with the 74LS30PC among its other parts. Its parts include 15 ICs, 9 capacitors, 9 connectors and 1 switch.

Main components

4

README

README.md

Junior Computer Replica

Junior Computer Front

Junior Computer Back

The Junior Computer is a 6502 SBC made by Elektor in 1980. It looks a lot like a KIM-1.

This is a replica PCB I made with KiCAD.

The best source of information for this computer is Elektor Magazine from 80's , but you can find a lot on this website : http://retro.hansotten.nl/6502-sbc/elektuur-junior/

This board is not a 100% accurate replica, because I have added directly on the PCB a few updates published later by Elektor :

  • a fix for memory decoding needed for the expansion board
  • the main decoupling capacitor C2 was on wrong side of S25 (activate display) which could reset the computer
  • a simple reset circuit with a resistor and a capacitor

I also replaced the 2708 EPROM by a 2716, which avoid the need of an hard to find EPROM & EPROM programmer, and has the big benefit of reducing the required power supplies from 3 (+5,-5,+12) to only +5V.

This work is licenced under CC BY-NC-SA (Attribution-NonCommercial-ShareAlike)

BOM

QtyReferenceValueComment
1C110p
1C247µ 6V tantale
2C3, C4100n MKH
8C5...C9, C10, C11, C141µ 16V tantale
1C12470nF MKH
2D1, D31N4148
1IC1MC6502
1IC1074LS01
1IC11ULN2003
1IC22716
1IC3MC6532probably the first part to look at !
2IC4 IC52114static RAM, search on Ebay
2IC7 IC674LS145
1IC8NE556
1IC974LS00
1J2DIN41612 32 A+C angled male
1J3DIN41617-31 straight female
2R17 R192k2
2R18 R2068k
1R1330K
6R2 R3 R4 R16 R14 R153k3
2R22 R211k
1R23820k
1R54k7
1R6330
7R7 R8 R9 R10 R12 R13 R1168
21S1…S23Digitast 12.7mm16 black, 4 red, 1 red with integrated LED, 2 blue, but see below
1S24DPDT lever switchwith soldering lugs
1S25SPDT lever switchwith soldering lugs
1X.Tal11Mhzcan be hard to find !
3Socket DIP-14
3Socket DIP-16
2Socket DIP-18
1Socket DIP-24
2Socket DIP-40
6Di1 ... Di6MAN4640A7 segment display

IF you cannot find 2114 RAMs , you can try the small board on "board adapter" folder (warning : not tested !) which should allow to use a 6116 RAM instead and plugs into the 2114 sockets

The Digitast keys (https://www.digikey.com/catalog/en/partgroup/digitast-series/15959) are the most expensives parts of this project. You can also use square tactile switchs instead (but it's not as pretty !)

An other thing to consider is the marking : the black keys need white marking, which can be hard to do. So think of how you will do the marking before choosing the colors of the keys !

Ordering the PCB

Use you favorite online PCB seller, and order 2 double-sided PCBs (display + computer) from the KiCad output files.

The real ones from Elektor where blue on component side and red on solder side, but if you order a blue PCB it will be close enough (and very nice).

Building the computer

The building is pretty straightforward (look at the original documentation). Components are soldered on one side, buttons and disply on the other side.

S24 and S25 switchs needs wires from the switchs lugs to the PCB (I used cutoff of resistor leads)

To connect the display to the main board, I used long SIL connectors (15-20mm long) soldered on both side, then I bent the display to ~30°

Don't forget the two small wire jumpers on front side : one from ground to letter "D" and the other one from K6 to the center pin.

If you want to use the file sticker-juniorcomputer.svg, first install the font "Microgramma D Extended Bold" on your system.

Programming the EPROM

I use a TL866 II plus for this, but anything that works is OK.

Program the 2716 with the file 2716_junior_monitor_ram_05_1980.bin

First tests

The power supply is available on both connectors, you just need 0v and +5V (1amp should be more than enough).

All the display should light up (check that the DISPLAY switch is ON). If you see some display ON, some display OFF, it could be a bad MC6532 (don't ask how I know that ...)

If nothing happens, press the reset switch to start the computer.

Typing numbers on keyboard should update the display.

You can find test programs on http://retro.hansotten.nl

Going further

It would be great to be able to load and save data, and also to have a serial terminal for typing programs. It's exactly the purpose of the Junior Interface board ! Look into the folder "junior-interface" for more infos !

Now I'm sure you want to run BASIC on the Junior, no problem, just build the memory expansion from "junior-universal-memory" folder and you're good to go !

Status

Working

  • junior-computer : the computer, built and tested OK
  • junior-computer-display: the 7 segments display, built and tested OK
  • junior-interface : the 2nd board adding various I/O to the computer, built and tested OK
  • junior-internal-conn : internal bus between computer and interface, built and tested OK
  • junior-internal-bus : a small PCB for linking the computer and the interface board, built and tested OK
  • junior-bus : Elektor expansion bus. Not tested, built and tested OK
  • junior-universal-memory : a RAM/EPROM board for the computer, built and tested OK

Not tested

  • ram-adapter : replace 2x2114 by 1x6116 RAM. Not tested
text
Any question ? --> Mastodon @LaurentFr@piaille.fr

Parts

38
QtyValueFootprintReferences
85564elektor:DIL-28IC8, IC9, IC10, IC11, IC12, IC13, IC14, IC15
8Conn_01x03_Pinelektor:CONN-3J2, J3, J4, J5, J6, J7, J8, J9
4100nelektor:CAP-3C6, C7, C8, C9
4100nelektor:CAP-4C1, C2, C3, C4
274LS138elektor:DIL-16IC4, IC5
274LS373elektor:DIL-20IC1, IC2
2R_Network08elektor:RES-NET-8RN1, RN3
110µelektor:CAP-POL-3C5
174LS00elektor:DIL-14IC6
174LS245elektor:DIL-20IC3
174LS30elektor:DIL-14IC7
1C64ACelektor:DIN-41612-ACJ1
1R_Network04elektor:RES-NET-4RN4
1R_Network09elektor:RES-NET-9RN2
1SW_DIP_x08elektor:SW-8SW1

More from laurent-fr/junior_computer_replica

7
  • 2 layers217.2 × 113 mmJunior interface, the printed circuit board in 3D

    Junior interface

    laurent-fr/junior_computer_replica

    A replica of the Junior Computer (a KIM-1 clone) published by Elektor in the 80's

    120 parts14
  • 2 layers217.2 × 113 mmJunior computer, the printed circuit board in 3D

    Junior computer

    laurent-fr/junior_computer_replica

    A replica of the Junior Computer (a KIM-1 clone) published by Elektor in the 80's

    86 parts14
  • 2 layers116.8 × 100 mmJunior bus, the printed circuit board in 3D

    Junior bus

    laurent-fr/junior_computer_replica

    A replica of the Junior Computer (a KIM-1 clone) published by Elektor in the 80's

    15 parts14
  • 2 layers77.5 × 31.8 mmJunior computer display, the printed circuit board in 3D

    Junior computer display

    laurent-fr/junior_computer_replica

    A replica of the Junior Computer (a KIM-1 clone) published by Elektor in the 80's

    11 parts14
  • 2 layers91.4 × 19.7 mmJunior interface conn, the printed circuit board in 3D

    Junior interface conn

    laurent-fr/junior_computer_replica

    A replica of the Junior Computer (a KIM-1 clone) published by Elektor in the 80's

    9 parts14
  • 2 layers34.3 × 33 mmRam adapter, the printed circuit board in 3D

    Ram adapter

    laurent-fr/junior_computer_replica

    A replica of the Junior Computer (a KIM-1 clone) published by Elektor in the 80's

    5 parts14
  • 2 layers99.1 × 46.8 mmJunior internal bus, the printed circuit board in 3D

    Junior internal bus

    laurent-fr/junior_computer_replica

    A replica of the Junior Computer (a KIM-1 clone) published by Elektor in the 80's

    2 parts14

Similar boards

  • 4 layers304.8 × 215.9 mm64 256KB SYSTEM BOARD, the printed circuit board in 3D

    64 256KB SYSTEM BOARD

    kev-ju/PC-Retro-MTM

    Modern KiCad version of the IBM 5150 system board originally created by MTM Scientific, Inc.

    197 parts4
  • 4 layers236.8 × 240.9 mmDIY Video, the printed circuit board in 3D

    DIY Video

    jimbro1000/DIY-Video

    General purpose video system for 8-bit computers using 74LS logic

    315 parts1
  • 6 layers244 × 244 mmRetroslop, the printed circuit board in 3D

    Retroslop

    CPTforever/8088-MicroATX-Computer

    A 8088 based, IBM 5150 like computer compatible with the MicroATX motherboard form factor.

    193 parts
  • 2 layers364 × 203 mmCPU6S, the printed circuit board in 3D

    CPU6S

    Meisaka/CenMiniCom

    Centurion Minicomputer Schematics

    240 parts8
  • 2 layers365.1 × 203.2 mmDIAG, the printed circuit board in 3D

    DIAG

    Nakazoto/CenturionComputer

    This is just a simple backup of all the files related to the Centurion that I have stored on my HD. The Wiki itself has far more in-depth information about the Centurion and it's individual cards.

    150 parts172
  • 2 layers350 × 224.3 mmConsole, the printed circuit board in 3D

    Console

    danwerner21/TI99_22

    a 2022 replica of the classic TI/994a, using obtainable parts

    251 parts50
  • 2 layers99.7 × 99.1 mmC64 Z80 Module, the printed circuit board in 3D

    C64 Z80 Module

    tebl/C64-CPM-Cartridge

    A recreation of the CP/M cartridge for the Commodore 64.

    34 parts27
  • 2 layers221.5 × 149.5 mmZX1, the printed circuit board in 3D

    ZX1

    misterblack1/zenith_zt1

    Information gathered on the Zenith ZT-1 / ZT-10 / ZT-11 and ZTX/ZT-x-A variants

    140 parts5

Questions

How big is the Junior universal memory PCB?

It measures 160 × 100 mm and has 2 copper layers, 1.6 mm thick.

What parts does the Junior universal memory use?

38 parts, built around the 74LS373SC, 74LS245SC, 74LS00SC and 74LS30PC. The full list of its parts is on this page, with links to each part's symbol and footprint where PCBKit's library has them.

Where can I download the Junior universal memory KiCad files?

From the laurent-fr/junior_computer_replica repository on GitHub, at the commit this page was made from: the board is junior-universal-memory/kicad/junior-universal-memory.kicad_pcb and its schematic junior-bus/junior-bus.kicad_sch. PCBKit opens the board in the browser, with nothing to install.

Can I use the Junior universal memory design in my own project?

Its repository states no licence, so its author keeps all rights: ask laurent-fr before reusing the design.