2 layers282.7 × 108.3 mm
2 layers350 × 224.3 mm
Console
danwerner21/TI99_2250a 2022 replica of the classic TI/994a, using obtainable parts
- Size
- 350 × 224.3 mm
- Copper layers
- 2
- Thickness
- 1.6 mm
- Parts
- 251
- Nets
- 354
- Pads
- 1,523
- Tracks, vias
- 9,062, 592
- Pours
- 6
- Routed
- Yes
- KiCad
- KiCad 6 (file 20211014)
- Created
- 24 Jun 2022
- Updated
- 5 Oct 2024
Overview
Console is an open-source printed circuit board by danwerner21, from the danwerner21/TI99_22 repository on GitHub. It is a 2-layer board of 350 × 224.3 mm with 251 parts on 354 nets, routed with 9,062 tracks and 592 vias.
It is built around the 74LS367PC, 74LS245SC and 74LS373SC, with the 74LS04PC, 74LS00SC and 74LS574N among its other parts. Its parts include 77 resistors, 75 capacitors, 38 ICs, 11 inductors and 4 transistors.
Main components
12
74LS367PC
PDIP-16Buffers, Drivers, Receivers, TransceiversTexas Instruments74LS245SC
-0℃~+70℃ 12ns@5V,45pF 15mA 24mA 4.75V~5.25V 74LS 8 Bidirectional Output enable Schmitt trigger Tri-State - Buffers, Drivers, Receivers, Transceivers ROHSTexas InstrumentsBuffers, Drivers, Receivers, Transceivers
74LS373SC
--55℃~+125℃ 1 2.6mA 24mA 38ns@5V,150pF 4.75V~5.25V 74LS 8 Output enable Tri-State - Buffers, Drivers, Receivers, Transceivers ROHSTexas InstrumentsBuffers, Drivers, Receivers, Transceivers
74LS04PC
PDIP-140℃~+70℃ 4.75V~5.25V 6 6.6mA 74LS PDIP-14 InvertersonsemiInverters
74LS00SC
-0℃~+70℃ 15ns@5V,50pF 2 2.7V 2V 4 4.75V~5.25V 400uA 500mV 74LS 800mV 8mA NAND Gate - Logic Gates ROHSTexas InstrumentsLogic Gates74LS574N
-0ns 0℃~+70℃ 1 2.6mA 20ns 24mA 28ns@5V,45pF 35MHz 4.75V~5.25V 74LS Series 8 D-Type Rising Edge Tri-State - Flip Flops ROHSRochester Electronics, LLCFlip Flops
HM62256BLP-7
DIP28DIP28 New Arrivals ROHSHITUncategorised
74LS32SC
-- Logic Gates ROHSTexas InstrumentsLogic Gates74LS03P-E
DIP-14-20℃~+75℃ 100uA 2 2V 32ns@5V,15pF 4 4.75V~5.25V 500mV 74LS 800mV 8mA NAND Gate Open Collector DIP-14 Logic Gates ROHSRenesas ElectronicsLogic Gates74LS156PC
PDIP-16-20℃~+75℃ 100uA 4.75V~5.25V 53ns@5V,50pF 6.1mA 74LS 8mA Decoder Reverse function Single Supply PDIP-16 Signal Switches, Multiplexers, Decoders ROHSonsemiSignal Switches, Multiplexers, Decoders74LS194PC
-0.4mA 0℃~+70℃ 25MHz 35ns@5V,50pF 4 4.75V~5.25V 74LS 8mA Asynchronous clear function、Asynchronous parallel load function、Supports forward and reverse shift - Shift RegistersTexas InstrumentsShift Registers74LS379PC
PDIP-160℃~+70℃ 18mA 20ns 27ns@5V,15pF 30MHz 4 4 5V 5ns 74LS Series Complementary D-Type Enable Rising Edge PDIP-16 Flip FlopsTexas InstrumentsFlip Flops
README
README.mdTexas Instruments TI99/4A Clone(ish) Project
Note that this is not a fully tested project at this point. . . .
This is based Rob Krenicki's design that is based on the HackMac KiCAD schematics. I have made several changes to the original design including:
- Placing 32K of 16bit wide fast ram on the board to fully populate the address space
- Placing an EPROM on the main board that can be used as an on-board cartridge ROM
- adding a header to allow a microcontroller to replace the GROM chips (hopefully this can be moved on-board soon)
- replacing the video DRAM with SRAM
- Updating the Keyboard header to support a soft caps lock switch on the keyboard PCB
- designing a Cherry MX keyboard
- adding headers for the GROM and expansion port to support riser cards for these ports
If there are any questions, I can be reached at vic2020Dan at gmail dot com.
ToDo
-
Cleanup/Documentation Possible Future Thoughts:
-
Redo the Board in an ATX form factor with PEB slots on board
-
Add Support for the Pico9918 on-board
-
Add Support for a Tang Nano FPGA TMS9918 replacement
-
Add Hex-bus port
-
Add a DIN 5-pin Composite video/Audio out.
-
Add built in speech synthesis
-
Clone Disk IO card
-
Relocate all the ports to the back of the motherboard
-
It has been suggested that we also have a console style version of the next revision as not everyone has a desire for a larger PE style machine
-
Also perhaps add some keys to the keyboard
DIP Switch Settings
The DIP switch on the main board allows one to configure which bank areas are populated with RAM.
RAM0 enables RAM to addresses >2000-3FFF (Lo Memory Expansion) RAM1 enables RAM to addresses >A000-BFFF (Hi Memory Expansion) RAM2 enables RAM to addresses >C000-DFFF (Hi Memory Expansion) RAM3 enables RAM to addresses >E000-FFFF (Hi Memory Expansion) RAM4 enables RAM to addresses >8000-83FF (Normal TI Scratch Pad RAM)
Note that I have never actually tested off-board 8 bit RAM, so this is new territory and might need some debugging 😊
also on-board RAM is 16 bit – so all of those external RAM sources will be slower.
Bugs
-
on rev 0.95 R36-40 are listed as 100K ohm, they are actually 100 ohm
-
on rev 0.95 the joystick and cassette connectors are mirrored and need to be mounted on the bottom side of the board to function
-
Both of these are corrected in 0.96
-
The reset button J1 should be attached to pin 5 of U1 not Pin 4
Bill of Materials
Console
| Qty | Reference(s) | Part |
|---|---|---|
| 6 | C1, C9, C11, C58, C73, C75 | 0.001uF |
| 1 | C2 | 22pF |
| 3 | C3, C5, C59 | 22uF |
| 12 | C4, C7, C13, C14, C20, C54, C55, C62, C64, C68, C71, C74 | 0.1uF |
| 1 | C6 | 1uF |
| 7 | C8, C52, C63, C65, C66, C67, C72 | 0.01uF |
| 1 | C10 | 100uF |
| 1 | C12 | 0.01uF |
| 7 | C15, C16, C17, C19, C21, C22, C60 | 100uF |
| 30 | C18, C23, C24, C25, C26, C27, C28, C29, C30, C31, C32, C33, C34, C35, C36, C37, C38, C39, C40, C41, C42, C43, C44, C45, C46, C47, C48, C49, C50, C51 | 0.1uF |
| 1 | C53 | 100uF |
| 1 | C56 | 12pF |
| 1 | C57 | 56pF |
| 1 | C61 | 220uF |
| 1 | C69 | 220pF |
| 1 | C70 | 0.022uF |
| 2 | CR1, CR4 | 1N4148 |
| 2 | CR2, CR3 | 1N914B |
| 1 | D1 | LED |
| 1 | J1 | Connector PinHeader 2.54mm:PinHeader 1x02 P2.54mm Vertical |
| 1 | J2 | Connector PinHeader 2.54mm:PinHeader 1x02 P2.54mm Vertical |
| 1 | J3 | TerminalBlock RND:TerminalBlock RND 205-00278 1x04 P5.00mm Vertical |
| 1 | J4 | Connector PinHeader 2.54mm:PinHeader 1x16 P2.54mm Vertical |
| 2 | J5, J6 | Connector PinHeader 2.54mm:PinHeader 1x03 P2.54mm Vertical |
| 1 | J7 | Connector PinHeader 2.54mm:PinHeader 1x03 P2.54mm Vertical |
| 1 | J8 | Connector PinHeader 2.54mm:PinHeader 1x02 P2.54mm Vertical |
| 1 | J9 | Connector PinHeader 2.54mm:PinHeader 1x02 P2.54mm Vertical |
| 1 | J10 | Connector Dsub:DSUB-9 Female Horizontal P2.77x2.84mm EdgePinOffset4.94mm Housed MountingHolesOffset7.48mm |
| 1 | J11 | Connector PinHeader 2.54mm:PinHeader 1x18 P2.54mm Vertical |
| 1 | J12 | Connector PinHeader 2.54mm:PinHeader 2x22 P2.54mm Vertical |
| 1 | J13 | WernerCustomLibrary:44 Pin Card Edge |
| 1 | J14 | Library:CardEdge 34Pin 2.54mm Vertical |
| 1 | J15 | Connector PinHeader 2.54mm:PinHeader 2x18 P2.54mm Vertical |
| 1 | J16 | Connector PinSocket 2.54mm:PinSocket 1x03 P2.54mm Vertical |
| 1 | J17 | Connector PinSocket 2.54mm:PinSocket 1x03 P2.54mm Vertical |
| 1 | J18 | Connector Dsub:DSUB-9 Female Horizontal P2.77x2.84mm EdgePinOffset4.94mm Housed MountingHolesOffset7.48mm |
| 1 | L1 | 0.33uH |
| 2 | L4, L5 | 6.8uH |
| 1 | L7 | 5.8uH |
| 1 | L8 | INDUCTOR (Ferrite BEAD) |
| 7 | L10, L11, L12, L13, L14, L15, L16 | 8.2uH |
| 3 | Q1, Q3, Q4 | TIS92 |
| 1 | Q2 | 2N3904 |
| 1 | R1 | 150k |
| 7 | R2, R9, R11, R18, R34, R35, R46 | 1k |
| 1 | R3 | 12k |
| 1 | R4 | 47k |
| 4 | R5, R6, R7, R8 | 22 |
| 5 | R10, R26, R45, R52, R53 | 4.7k |
| 5 | R12, R13, R14, R15, R16 | 1K |
| 3 | R17, R48, R50 | 2.2k |
| 2 | R19, R30 | 470 |
| 1 | R20 | 270 |
| 1 | R21 | 1.5k x 9 SIP bussed |
| 1 | R22 | 361 |
| 3 | R23, R73, R75 | 5.6k |
| 2 | R24, R27 | 10 |
| 1 | R25 | 150 |
| 1 | R28 | 470k |
| 1 | R29 | 0 |
| 2 | R31, R33 | 75 |
| 1 | R32 | 470 |
| 4 | R41, R42, R43, R44 | 62 |
| 1 | R47 | 3.3k |
| 9 | R36, R37, R38, R39, R40, R49, R51, R54, R56 | 100 |
| 1 | R55 | 330 |
| 1 | R57 | 10k |
| 1 | R58 | 6.8k |
| 1 | R59 | 39k |
| 1 | R60 | 6.8k |
| 4 | R61, R62, R67, R68 | 1K |
| 1 | R63 | 120k |
| 1 | R64 | 2.7k |
| 3 | R65, R66, R76 | 220 |
| 1 | R69 | 10K |
| 1 | R70 | 9.1k |
| 2 | R71, R72 | 10k |
| 1 | R74 | 5.6K |
| 1 | R77 | 15 |
| 2 | RN1, RN2 | 10K x 9 SIP Bussed |
| 1 | SW1 | DIP switchx05 |
| 1 | SW2 | Pin Header 01x02 Male |
| 1 | U1 | TMS9904 (note this needs to be a 9904 not 9904ANL. If the 9904ANL is used, Y1 needs to be substituted with 12Mhz, L1 needs to be substituted with 3.3uh and C2 needs to be substituted with 50pf) |
| 1 | U2 | TMS9900 |
| 4 | U3, U15, U22, U24 | 74LS04 |
| 2 | U4, U9 | 74LS32 |
| 2 | U5, U8 | 74LS138 |
| 1 | U6 | 74LS03 |
| 1 | U7 | 74LS08 |
| 3 | U10, U14, U18 | 74LS00 |
| 2 | U11, U41 | 74LS244 |
| 1 | U12 | 74LS373 |
| 1 | U13 | 74LS245 |
| 1 | U16 | 74LS74 |
| 1 | U17 | 74LS194 |
| 1 | U19 | LM2901 |
| 1 | U20 | LM7905 TO220 |
| 1 | U21 | LM2903 |
| 3 | U26, U27, U28 | TMC0430 |
| 3 | U29, U30, U37 | HM62256BLP |
| 2 | U31, U32 | 27C64 |
| 1 | U33 | SN76489 |
| 1 | U34 | TMS9918 |
| 3 | U35, U36, U38 | 74LS574 |
| 1 | U39 | TMS9901 |
| 1 | U40 | 74LS156 |
| 2 | U42, U43 | 74LS367 |
| 1 | U44 | 74LS379 |
| 1 | U45 | 27C010 |
| 1 | U46 | RC4558 |
| 1 | U47 | 74LS06 |
| 2 | U48, U49 | TIL119 |
| 1 | Y1 | 48.000 MHz Crystal |
| 1 | Y2 | 10.7MHz Crystal |
Keyboard
| Qty | Reference(s) | Value | Part |
|---|---|---|---|
| 1 | C1 | 0.1uF | Capacitor |
| 1 | D1 | LED | LED |
| 1 | D2 | LED | LED |
| 1 | J1 | Pin Header 1x18 male | Pin Header 1x18 male |
| 2 | R1, R2 | 470 ohm | Resistor |
| 1 | R3 | 1K ohm | Resistor |
| 48 | SW1-SW48 | Mechanical Switch | Cherry MX Switch (or compatible) |
| 1 | U1 | ATtiny13A-P | IC |
| 1 | U2 | 74LS125 | IC |
| 3 | Switch Stabilizer 2.25 | ||
| 1 | Switch Stabilizer 6.25 | ||
| 1 | Optional Alignment frame (will need modified) | ||
| Stabilizers (frame not used): | https://www.amazon.com/Genuine-Cherry-PCB-Snap-Stabilizers/dp/B085T8QZJC | ||
| Stabilizers (Frame used) | https://www.amazon.com/dp/B082X4V9VC | ||
| Frame: | https://www.amazon.com/gp/product/B07MMB33WG |
Cartridge Riser
| Qty | Reference(s) | Part | Type |
|---|---|---|---|
| 1 | J1 | Pin Header 01x18 Male | Pin Header 01x18 Male |
| 1 | J2 | 36 Pin Edge Connector | CONN EDGE DUAL FMALE 36POS 0.100 spacing |
IO Riser
| Qty | Reference(s) | Part | Type |
|---|---|---|---|
| 1 | J1 | Pin Header 2x22 Male | Pin Header 2x22 Male |
UNICORN BOARD
| Qty | Reference(s) | Part | Type |
|---|---|---|---|
| 1 | J1 | Pin Header Socket 01x16 Female Right Angle | Pin Header Socket 01x16 Female Right Angle |
| 4 | U1-U4 | Level Shifter | https://www.amazon.com/KeeYees-Channels-Converter-Bi-Directional-Shifter/dp/B07LG646VS |
| 1 | U5 | ESP32 Devkit | https://www.amazon.com/Development-Microcontroller-Integrated-Antenna-Amplifiers/dp/B09GK74F7N |
License
The original project was licensed under the Creative Commons - Attribution - ShareAlike 3.0 License
Attribution
This board was derrived from works by, uses design elements from, or contains sofware writen by the following:
- Rob Krenicki (https://github.com/rkrenicki/TI99-Motherboard)
- HackMac (https://bitbucket.org/hackmac/ti-schematics/wiki/Home)
Parts
251| Qty | Value | Footprint | References |
|---|---|---|---|
| 42 | 0.1µF | Capacitor_THT:C_Rect_L7.0mm_W2.0mm_P5.00mm | C13, C14, C18, C20, C23, C24, C25, C26, C27, C28, C29, C30, C31, C32, C33, C34 +26 |
| 9 | 100Ω | Resistor_THT:R_Axial_DIN0207_L6.3mm_D2.5mm_P7.62mm_Horizontal | R36, R37, R38, R39, R40, R49, R51, R54, R56 |
| 9 | 1KΩ | Resistor_THT:R_Axial_DIN0207_L6.3mm_D2.5mm_P7.62mm_Horizontal | R12, R13, R14, R15, R16, R61, R62, R67, R68 |
| 8 | 0.01µF | Capacitor_THT:C_Rect_L7.0mm_W2.0mm_P5.00mm | C8, C12, C52, C63, C65, C66, C67, C72 |
| 8 | 100µF | Capacitor_THT:CP_Radial_D7.5mm_P2.50mm | C10, C15, C16, C17, C19, C21, C22, C60 |
| 7 | 1kΩ | Resistor_THT:R_Axial_DIN0207_L6.3mm_D2.5mm_P7.62mm_Horizontal | R2, R9, R11, R18, R34, R35, R46 |
| 7 | 8.2µh | Resistor_THT:R_Axial_DIN0207_L6.3mm_D2.5mm_P15.24mm_Horizontal | L10, L11, L12, L13, L14, L15, L16 |
| 7 | MountingHole | MountingHole:MountingHole_3.2mm_M3 | H1, H2, H3, H4, H5, H6, H7 |
| 6 | 0.001µF | Capacitor_THT:C_Rect_L7.0mm_W2.0mm_P5.00mm | C1, C9, C11, C58, C73, C75 |
| 5 | 4.7kΩ | Resistor_THT:R_Axial_DIN0207_L6.3mm_D2.5mm_P7.62mm_Horizontal | R10, R26, R45, R52, R53 |
| 4 | 22Ω | Resistor_THT:R_Axial_DIN0207_L6.3mm_D2.5mm_P7.62mm_Horizontal | R5, R6, R7, R8 |
| 4 | 62Ω | Resistor_THT:R_Axial_DIN0207_L6.3mm_D2.5mm_P7.62mm_Horizontal | R41, R42, R43, R44 |
| 4 | 74LS04 | Package_DIP:DIP-14_W7.62mm_Socket_LongPads | U3, U15, U22, U24 |
| 3 | 10kΩ | Resistor_THT:R_Axial_DIN0207_L6.3mm_D2.5mm_P7.62mm_Horizontal | R57, R71, R72 |
| 3 | 2.2kΩ | Resistor_THT:R_Axial_DIN0207_L6.3mm_D2.5mm_P7.62mm_Horizontal | R17, R48, R50 |
| 3 | 220Ω | Resistor_THT:R_Axial_DIN0207_L6.3mm_D2.5mm_P7.62mm_Horizontal | R65, R66, R76 |
| 3 | 22µF | Capacitor_THT:CP_Radial_D7.5mm_P2.50mm | C3, C5, C59 |
| 3 | 470Ω | Resistor_THT:R_Axial_DIN0207_L6.3mm_D2.5mm_P7.62mm_Horizontal | R19, R30, R32 |
| 3 | 5.6kΩ | Resistor_THT:R_Axial_DIN0207_L6.3mm_D2.5mm_P7.62mm_Horizontal | R23, R73, R75 |
| 3 | 74LS00 | Package_DIP:DIP-14_W7.62mm_Socket_LongPads | U10, U14, U18 |
| 3 | 74LS574 | Package_DIP:DIP-20_W7.62mm_Socket_LongPads | U35, U36, U38 |
| 3 | HM62256BLP | Package_DIP:DIP-28_W15.24mm_Socket_LongPads | U29, U30, U37 |
| 3 | TIS92 | Package_TO_SOT_THT:TO-92_HandSolder | Q1, Q3, Q4 |
| 3 | TMC0430 | Package_DIP:DIP-16_W7.62mm_Socket_LongPads | U26, U27, U28 |
| 2 | 10K | Resistor_THT:R_Array_SIP10 | RN1, RN2 |
| 2 | 10Ω | Resistor_THT:R_Axial_DIN0207_L6.3mm_D2.5mm_P7.62mm_Horizontal | R24, R27 |
| 2 | 1N4148 | Diode_THT:D_A-405_P7.62mm_Horizontal | CR1, CR4 |
| 2 | 1N914B | Diode_THT:D_A-405_P7.62mm_Horizontal | CR2, CR3 |
| 2 | 27C64 | Package_DIP:DIP-28_W15.24mm_Socket_LongPads | U31, U32 |
| 2 | 6.8kΩ | Resistor_THT:R_Axial_DIN0207_L6.3mm_D2.5mm_P7.62mm_Horizontal | R58, R60 |
| 2 | 6.8µH | Resistor_THT:R_Axial_DIN0207_L6.3mm_D2.5mm_P15.24mm_Horizontal | L4, L5 |
| 2 | 74LS138 | Package_DIP:DIP-16_W7.62mm_Socket_LongPads | U5, U8 |
| 2 | 74LS244 | Package_DIP:DIP-20_W7.62mm_Socket_LongPads | U11, U41 |
| 2 | 74LS32 | Package_DIP:DIP-14_W7.62mm_Socket_LongPads | U4, U9 |
| 2 | 74LS367 | Package_DIP:DIP-16_W7.62mm_Socket_LongPads | U42, U43 |
| 2 | 75Ω | Resistor_THT:R_Axial_DIN0207_L6.3mm_D2.5mm_P7.62mm_Horizontal | R31, R33 |
| 2 | ROM Select | Connector_PinHeader_2.54mm:PinHeader_1x03_P2.54mm_Vertical | J5, J6 |
| 2 | TIL119 | Package_DIP:DIP-6_W7.62mm_Socket_LongPads | U48, U49 |
| 1 | 0.022µF | Capacitor_THT:C_Rect_L7.0mm_W2.0mm_P5.00mm | C70 |
| 1 | 0.33µH | Resistor_THT:R_Axial_DIN0207_L6.3mm_D2.5mm_P15.24mm_Horizontal | L1 |
| 1 | 0Ω | Resistor_THT:R_Axial_DIN0207_L6.3mm_D2.5mm_P7.62mm_Horizontal | R29 |
| 1 | 1.5kΩ | Resistor_THT:R_Array_SIP10 | R21 |
| 1 | 10.7MHz | Crystal:Crystal_HC49-U_Vertical | Y2 |
| 1 | 100µF | Capacitor_THT:CP_Radial_D5.0mm_P2.00mm | C53 |
| 1 | 10KΩ | Resistor_THT:R_Axial_DIN0207_L6.3mm_D2.5mm_P7.62mm_Horizontal | R69 |
| 1 | 120kΩ | Resistor_THT:R_Axial_DIN0207_L6.3mm_D2.5mm_P7.62mm_Horizontal | R63 |
| 1 | 12kΩ | Resistor_THT:R_Axial_DIN0207_L6.3mm_D2.5mm_P7.62mm_Horizontal | R3 |
| 1 | 12pF | Capacitor_THT:C_Rect_L7.0mm_W2.0mm_P5.00mm | C56 |
| 1 | 150kΩ | Resistor_THT:R_Axial_DIN0207_L6.3mm_D2.5mm_P7.62mm_Horizontal | R1 |
| 1 | 150Ω | Resistor_THT:R_Axial_DIN0207_L6.3mm_D2.5mm_P7.62mm_Horizontal | R25 |
| 1 | 15Ω | Resistor_THT:R_Axial_DIN0207_L6.3mm_D2.5mm_P7.62mm_Horizontal | R77 |
| 1 | 1µF | Capacitor_THT:C_Rect_L7.0mm_W2.0mm_P5.00mm | C6 |
| 1 | 2.7kΩ | Resistor_THT:R_Axial_DIN0207_L6.3mm_D2.5mm_P7.62mm_Horizontal | R64 |
| 1 | 220pF | Capacitor_THT:C_Rect_L7.0mm_W2.0mm_P5.00mm | C69 |
| 1 | 220µF | Capacitor_THT:CP_Radial_D7.5mm_P2.50mm | C61 |
| 1 | 22pF | Capacitor_THT:C_Rect_L7.0mm_W2.0mm_P5.00mm | C2 |
| 1 | 270Ω | Resistor_THT:R_Axial_DIN0207_L6.3mm_D2.5mm_P7.62mm_Horizontal | R20 |
| 1 | 27C010-C | Package_DIP:DIP-32_W15.24mm_Socket_LongPads | U45 |
| 1 | 2N3904 | Package_TO_SOT_THT:TO-92L_HandSolder | Q2 |
| 1 | 3.3kΩ | Resistor_THT:R_Axial_DIN0207_L6.3mm_D2.5mm_P7.62mm_Horizontal | R47 |
| 1 | 330Ω | Resistor_THT:R_Axial_DIN0207_L6.3mm_D2.5mm_P7.62mm_Horizontal | R55 |
| 1 | 361Ω | Resistor_THT:R_Axial_DIN0207_L6.3mm_D2.5mm_P7.62mm_Horizontal | R22 |
| 1 | 39kΩ | Resistor_THT:R_Axial_DIN0207_L6.3mm_D2.5mm_P7.62mm_Horizontal | R59 |
| 1 | 470kΩ | Resistor_THT:R_Axial_DIN0207_L6.3mm_D2.5mm_P7.62mm_Horizontal | R28 |
| 1 | 47kΩ | Resistor_THT:R_Axial_DIN0207_L6.3mm_D2.5mm_P7.62mm_Horizontal | R4 |
| 1 | 48.000 MHz | Crystal:Crystal_HC49-U_Vertical | Y1 |
| 1 | 5.6KΩ | Resistor_THT:R_Axial_DIN0207_L6.3mm_D2.5mm_P7.62mm_Horizontal | R74 |
| 1 | 5.8µH | Resistor_THT:R_Axial_DIN0207_L6.3mm_D2.5mm_P15.24mm_Horizontal | L7 |
| 1 | 56pF | Capacitor_THT:C_Rect_L7.0mm_W2.0mm_P5.00mm | C57 |
| 1 | 74LS03 | Package_DIP:DIP-14_W7.62mm_Socket_LongPads | U6 |
| 1 | 74LS06 | Package_DIP:DIP-14_W7.62mm_Socket_LongPads | U47 |
| 1 | 74LS08 | Package_DIP:DIP-14_W7.62mm_Socket_LongPads | U7 |
| 1 | 74LS156 | Package_DIP:DIP-16_W7.62mm_Socket_LongPads | U40 |
| 1 | 74LS194 | Package_DIP:DIP-16_W7.62mm_Socket_LongPads | U17 |
| 1 | 74LS245 | Package_DIP:DIP-20_W7.62mm_Socket_LongPads | U13 |
| 1 | 74LS373 | Package_DIP:DIP-20_W7.62mm_Socket_LongPads | U12 |
| 1 | 74LS379 | Package_DIP:DIP-16_W7.62mm_Socket_LongPads | U44 |
| 1 | 74LS74 | Package_DIP:DIP-14_W7.62mm_Socket_LongPads | U16 |
| 1 | 9.1kΩ | Resistor_THT:R_Axial_DIN0207_L6.3mm_D2.5mm_P7.62mm_Horizontal | R70 |
| 1 | AUDIO OUT | Connector_PinHeader_2.54mm:PinHeader_1x02_P2.54mm_Vertical | J8 |
The 223 most common of 251 parts.
More from danwerner21/TI99_22
4- 2 layers100 × 60 mm
- 2 layers17.4 × 69.8 mm
- 2 layers76.9 × 58.5 mm
Similar boards
- 4 layers244 × 244 mm
- 2 layers338.7 × 107.7 mm
- 2 layers76.3 × 147.3 mm
- 4 layers254 × 137.7 mm
S100 ColorMagic-1.1-006
RichCini/LomasBoards
Small repository of files/data related to Lomas Data Products S-100 boards.
150 parts1 - 2 layers407 × 184 mm
TRS-80-Model I G E1
RetroStack/TRS-80-Model-I-G-E1
Hardware Replica of the TRS-80 Model I Revision G
230 parts57MIT - 2 layers100 × 100 mm
- 2 layers400.9 × 280.5 mm
- 2 layers229.9 × 83.8 mm
Questions
How big is the Console PCB?
It measures 350 × 224.3 mm and has 2 copper layers, 1.6 mm thick.
What parts does the Console use?
251 parts, built around the 74LS367PC, 74LS245SC, 74LS373SC and 74LS04PC. The full list of its parts is on this page, with links to each part's symbol and footprint where PCBKit's library has them.
Where can I download the Console KiCad files?
From the danwerner21/TI99_22 repository on GitHub, at the commit this page was made from: the board is mainboard/Console.kicad_pcb and its schematic CartRiser/CartRiser/CartRiser.kicad_sch. PCBKit opens the board in the browser, with nothing to install.
Can I use the Console design in my own project?
Its repository states no licence, so its author keeps all rights: ask danwerner21 before reusing the design.