2 layers50 × 100 mm
Dimmer final
MateoCignetti/ProyectoFinal
Esta obra está bajo una [Licencia Creative Commons Atribución-NoComercial-CompartirIgual 4.0 Internacional][cc-by-nc-sa].
32 parts2
2 layers95.9 × 129.5 mm
Solderin Station
kr4fty/DiySolderingStation3Diy Soldering Stations with Atmega (Arduino UNO). Firmware and hardware design included
- Size
- 95.9 × 129.5 mm
- Copper layers
- 2
- Thickness
- 1.6 mm
- Parts
- 73
- Nets
- 77
- Pads
- 229
- Tracks, vias
- 420, 0
- Pours
- 4
- Routed
- Yes
- KiCad
- KiCad 4
- Created
- 11 Jul 2017
- Updated
- 13 Jul 2017
Overview
Solderin Station is an open-source printed circuit board by kr4fty, from the kr4fty/DiySolderingStation repository on GitHub, published under the GPL-2.0 licence. It is a 2-layer board of 95.9 × 129.5 mm with 73 parts on 77 nets, routed with 420 tracks and 0 vias.
It is built around the ATMEGA328P-PU, BT137 and LM358N, with the LM7805CT, MOC3021M and 100UF/16V among its other parts. Its parts include 21 resistors, 18 connectors, 11 capacitors, 7 diodes and 6 ICs. It belongs with the AVR (ATmega, ATtiny) boards of this library.
Main components
8
ATMEGA328P-PU
DIP-28-300mil-40℃~+85℃ 1.8V~5.5V 10bit 1KB 20MHz 23 2KB 32KB 8 Bit AVR Built-in FLASH DIP-28-300mil Microcontrollers (MCU/MPU/SOC) ROHSMicrochip TechnologyMicrocontrollers (MCU/MPU/SOC)
BT137
TO-252Thyristors (SCR)/ModulesJUXING
LM358N
DIP-8-18V~18V 0℃~+70℃ 1.2MHz 10nA 2 30mA 3V~36V 50nA 7mV 800uA 80dB Built-in compensation DIP-8 Operational Amplifier ROHSHGSEMIOperational Amplifier
LM7805CT
TO-2200℃~+70℃@(Ta) 1 1A 20V 2V@(1A) 40uV 5V 62dB@(120Hz) 8mA Fixed Over Current Protection、Short Circuit Protection、Thermal shutdown Positive TO-220 Voltage Regulators - Linear, Low Drop Out (LDO) Regulators ROHSTexas InstrumentsVoltage Regulators - Linear, Low Drop Out (LDO) Regulators
MOC3021M
DIP-6-40℃~+85℃ 0.1mA 1 1.15V 100mA 330mW 4.17kV 400V 6 60mA No TRIAC DIP-6 Triac, SCR Output Optoisolators ROHSonsemiTriac, SCR Output Optoisolators
100UF/16V
C1812C1812 SMT ROHSJLCPCB AssemblyUncategorised
BC337
TO-92-31 NPN 100 100MHz 100nA 45V 5V 625mW 700mV 800mA NPN TO-92-3 Bipolar (BJT) ROHSFoshan Blue Rocket ElecBipolar (BJT)100UF 10V 4*7
插件,4x7mm1.5mm 1000hrs@105℃ 100uF 10V 4mm 7mm 插件,4x7mm Aluminum Electrolytic Capacitors - Leaded ROHSLCSCAluminum Electrolytic Capacitors - Leaded
README
hardware/README.mdAbout
Created with KiCAD 4.0.6
Tapia Favio
Parts
73| Qty | Value | Footprint | References |
|---|---|---|---|
| 6 | 10K | Resistors_THT:R_Axial_DIN0204_L3.6mm_D1.6mm_P5.08mm_Horizontal | R2, R5, R13, R14, R18, R21 |
| 5 | 10K | Resistors_THT:R_Axial_DIN0204_L3.6mm_D1.6mm_P2.54mm_Vertical | R10, R16, R17, R19, R20 |
| 4 | MountingHole_2.2mm_M2 | Mounting_Holes:MountingHole_2.2mm_M2 | CHASSIS, CHASSIS, GND, GND |
| 3 | 100n | Capacitors_THT:C_Disc_D3.8mm_W2.6mm_P2.50mm | C10, C11, C13 |
| 3 | 1K | Resistors_THT:R_Axial_DIN0204_L3.6mm_D1.6mm_P5.08mm_Horizontal | R7, R9, R11 |
| 2 | 100uF/16V | Capacitors_THT:CP_Radial_D5.0mm_P2.50mm | C2, C3 |
| 2 | 1N4148 | Diodes_THT:D_DO-35_SOD27_P7.62mm_Horizontal | D7, D8 |
| 2 | 22pF | Capacitors_THT:C_Disc_D3.8mm_W2.6mm_P2.50mm | C5, C6 |
| 2 | 3.3K | Resistors_THT:R_Axial_DIN0207_L6.3mm_D2.5mm_P7.62mm_Horizontal | R3, R4 |
| 2 | BC337 | TO_SOT_Packages_THT:TO-92_Inline_Narrow_Oval | Q1, Q2 |
| 2 | LED | LEDs:LED_D3.0mm | D2, D5 |
| 1 | 100/1W | Resistors_THT:R_Axial_DIN0207_L6.3mm_D2.5mm_P7.62mm_Horizontal | R8 |
| 1 | 100n/600V | Capacitors_THT:C_Rect_L11.0mm_W3.5mm_P10.00mm_MKT | C7 |
| 1 | 100uF/10V | Capacitors_THT:CP_Radial_D5.0mm_P2.50mm | C4 |
| 1 | 10n | Capacitors_THT:C_Disc_D3.8mm_W2.6mm_P2.50mm | C12 |
| 1 | 16Mhz | Crystals:Crystal_HC52-6mm_Vertical | Y1 |
| 1 | 1K | Resistors_THT:R_Axial_DIN0207_L6.3mm_D2.5mm_P7.62mm_Horizontal | R1 |
| 1 | 2.2K | Resistors_THT:R_Axial_DIN0204_L3.6mm_D1.6mm_P2.54mm_Vertical | R12 |
| 1 | 2200uF/16v | Capacitors_THT:CP_Radial_D12.5mm_P5.00mm | C1 |
| 1 | 24Vac | Wire_Connections_Bridges:WireConnection_2.50mmDrill_LargePad | J8 |
| 1 | 330 | Resistors_THT:R_Axial_DIN0204_L3.6mm_D1.6mm_P5.08mm_Horizontal | R15 |
| 1 | 470 | Resistors_THT:R_Axial_DIN0204_L3.6mm_D1.6mm_P5.08mm_Horizontal | R6 |
| 1 | 4N25 | Housings_DIP:DIP-6_W7.62mm | U4 |
| 1 | 9Vac | Wire_Connections_Bridges:WireConnection_2.50mmDrill_LargePad | J10 |
| 1 | ATMEGA328P-PU | Housings_DIP:DIP-28_W7.62mm | U3 |
| 1 | BT137 | TO_SOT_Packages_THT:TO-220_Vertical | D4 |
| 1 | BUTTON_FEMALE | Connectors:PINHEAD1-2 | J13 |
| 1 | BUTTON_MALE | Connectors:PINHEAD1-2 | J14 |
| 1 | CONN_01X03 | Pin_Headers:Pin_Header_Straight_1x03_Pitch2.54mm | J18 |
| 1 | D_Bridge_-A+A | Diodes_THT:Diode_Bridge_18.5x5.5 | D1 |
| 1 | ENCODER_FEMALE | Connectors:PINHEAD1-3 | J12 |
| 1 | ENCODER_MALE | Connectors:PINHEAD1-3 | J11 |
| 1 | ICSP | Pin_Headers:Pin_Header_Straight_2x03_Pitch2.54mm | J1 |
| 1 | KBL210 | Diodes_THT:Diode_Bridge_18.5x5.5 | D3 |
| 1 | LCD_FEMALE | Pin_Headers:Pin_Header_Straight_1x07_Pitch2.54mm | J7 |
| 1 | LCD_I2C | Connectors:PINHEAD1-6 | J17 |
| 1 | LCD_MALE | Pin_Headers:Pin_Header_Straight_1x07_Pitch2.54mm | J6 |
| 1 | LED_FEMALE | Connectors:PINHEAD1-2 | J16 |
| 1 | LED_MALE | Connectors:PINHEAD1-2 | J15 |
| 1 | LM358N | Housings_DIP:DIP-8_W7.62mm_LongPads | U6 |
| 1 | LM7805CT | TO_SOT_Packages_THT:TO-220_Vertical | U1 |
| 1 | LM7833 | TO_SOT_Packages_THT:TO-220_Vertical | U2 |
| 1 | MOC3021M | Housings_DIP:DIP-6_W7.62mm | U5 |
| 1 | PAD_FEMALE | Pin_Headers:Pin_Header_Straight_1x04_Pitch2.54mm | J4 |
| 1 | PAD_MALE | Pin_Headers:Pin_Header_Straight_1x04_Pitch2.54mm | J3 |
| 1 | Reset | Buttons_Switches_THT:SW_PUSH_6mm | SW1 |
| 1 | Rotary_Encoder | Potentiometers:Potentiometer_Bourns_PTV09A-1_Horizontal | SW3 |
| 1 | SELECT | Buttons_Switches_THT:SW_PUSH_6mm | SW2 |
| 1 | SOLDERING IRON | Pin_Headers:Pin_Header_Straight_1x05_Pitch2.54mm | J5 |
| 1 | Serial | Pin_Headers:Pin_Header_Straight_1x04_Pitch2.54mm | J2 |
| 1 | Vcc IN | Connectors:PINHEAD1-3 | J9 |
Questions
How big is the Solderin Station PCB?
It measures 95.9 × 129.5 mm and has 2 copper layers, 1.6 mm thick.
What parts does the Solderin Station use?
73 parts, built around the ATMEGA328P-PU, BT137, LM358N and LM7805CT. The full list of its parts is on this page, with links to each part's symbol and footprint where PCBKit's library has them.
Where can I download the Solderin Station KiCad files?
From the kr4fty/DiySolderingStation repository on GitHub, at the commit this page was made from: the board is hardware/Solderin Station.kicad_pcb. PCBKit opens the board in the browser, with nothing to install.
Can I use the Solderin Station design in my own project?
Its repository publishes it under the GPL-2.0 licence: you may reuse it on that licence's terms (keep the author's notice, and for a copyleft licence share your changes alike).
Similar boards
- 2 layers150 × 100 mm
Star tracker ctrl
MikeMontana1968/star-tracker-gears
Sidereal star tracker: a 2048:1 printed gearbox, an ESP32 controller that runs a GoPro night lapse unattended, and a through-hole PCB generated from Python.
72 parts - 2 layers120 × 80 mm
Skysweep32 pro
bobberdolle1/SkySweep32
Open-source passive multi-band RF monitoring system | 855–925 MHz, 2.4 GHz, 5.8 GHz | Rev C first prototype
38 parts33GPL-3.0 - 2 layers101.6 × 50.8 mm
Light switch
NguyenThanhHuy-debug/PCB_Real-Time-Power-Monitoring-System-Development-Light-Switch
PCBReal-Time-Power-Monitoring-System-Development-Light-Switch — a software project built with modern tooling.
142 parts2 - 2 layers73.7 × 61 mm
- 2 layers96.3 × 98 mm
Aquarium
baranovskiykonstantin/aquarium
Control the lighting and the heating of the aquarium.
73 parts11 - 2 layers50.8 × 50.8 mm
- 2 layers100 × 70 mm
