4 layers42 × 42 mm
2 layers72.4 × 73.7 mm
Auto Headlight Control System
kmkim036/Auto-Headlight-Control-System1- Size
- 72.4 × 73.7 mm
- Copper layers
- 2
- Thickness
- 1.6 mm
- Parts
- 20
- Nets
- 83
- Pads
- 113
- Tracks, vias
- 43, 0
- Pours
- 4
- Routed
- Yes
- KiCad
- KiCad 5 (file 20171130)
- Created
- 10 Nov 2021
- Updated
- 30 Nov 2021
Overview
Auto Headlight Control System is an open-source printed circuit board by kmkim036, from the kmkim036/Auto-Headlight-Control-System repository on GitHub. It is a 2-layer board of 72.4 × 73.7 mm with 20 parts on 83 nets, routed with 43 tracks and 0 vias.
It is built around the SN65HVD230D, ADXL345-EP and AP3216SGC, with the SG90 among its other parts. Its parts include 4 ICs, 4 connectors, 2 diodes, 2 switches and 1 resistor. It belongs with the STM32 boards of this library.
Main components
4
SN65HVD230D
SOIC-8-40℃~+85℃ 1 17mA 1Mbps 370uA 3V~3.6V CAN Transceiver Low-power mode、Wake-up function、ESD protection、Thermal shutdown protection、Bus fault protection、Hot-swap protection SOIC-8 CAN Transceivers ROHSTexas InstrumentsCAN Transceivers
ADXL345-EP
LGA-14(3x5x0.8)LGA-14(3x5x0.8) New Arrivals ROHSAnalog DevicesUncategorised
AP3216SGC
1206- New Arrivals ROHSKingbrightUncategorised
SG90
1812-40℃~+90℃ 0.2mm 1pF 2 2.7mm 2kA 4.5mm 500V 90V 1812 Gas Discharge Tube Arresters (GDT) ROHSLittelfuseGas Discharge Tube Arresters (GDT)
README
README.mdProgram Language
C
When
Senior, 2nd semester in Automobile Electric System Design Class
Description
Automatic Headlight Control System
Measure data with Light sensor and Acceleration sensor
Control LED and Servo Motor
Use CAN communication to command
Parts
20| Qty | Value | Footprint | References |
|---|---|---|---|
| 4 | Pin_D1.0mm_L10.0mm | Connector_Pin:Pin_D1.0mm_L10.0mm | , , , |
| 2 | SN65HVD230 | Connector_PinHeader_2.54mm:PinHeader_1x04_P2.54mm_Vertical | T1, T2 |
| 2 | STM32_L | Connector_PinHeader_2.54mm:PinHeader_1x20_P2.54mm_Vertical | U1, U3 |
| 2 | STM32_R | Connector_PinHeader_2.54mm:PinHeader_1x20_P2.54mm_Vertical | U2, U4 |
| 1 | 100ohm | Resistor_THT:R_Axial_DIN0207_L6.3mm_D2.5mm_P7.62mm_Horizontal | R1 |
| 1 | ADXL345 | Connector_PinHeader_2.54mm:PinHeader_1x06_P2.54mm_Vertical | S1 |
| 1 | AP3216 | Connector_PinHeader_2.54mm:PinHeader_1x04_P2.54mm_Vertical | S2 |
| 1 | LED_anode | Connector_PinHeader_2.54mm:PinHeader_1x01_P2.54mm_Vertical | D1 |
| 1 | LED_cathode | Connector_PinHeader_2.54mm:PinHeader_1x01_P2.54mm_Vertical | D2 |
| 1 | SG90 | Connector_PinHeader_2.54mm:PinHeader_1x03_P2.54mm_Vertical | M1 |
| 1 | Serial_GND_1 | Connector_PinSocket_2.54mm:PinSocket_1x01_P2.54mm_Vertical | J2 |
| 1 | Serial_GND_2 | Connector_PinSocket_2.54mm:PinSocket_1x01_P2.54mm_Vertical | J4 |
| 1 | Serial_Tx_1 | Connector_PinSocket_2.54mm:PinSocket_1x01_P2.54mm_Vertical | J1 |
| 1 | Serial_Tx_2 | Connector_PinSocket_2.54mm:PinSocket_1x01_P2.54mm_Vertical | J3 |
Similar boards
- 4 layers102 × 100 mm
Zelvicka
RoboticsBrno/Robutek
Robůtek je robotická platforma založená na čipu ESP32-S3. Je velice rozšitiřelný, ale ze základu umí jezdit, kreslit fixou, jezdit po čáře, pohybovat se bludištěm. Programování je přes Jaculus.
214 parts12 - 2 layers119.4 × 98.9 mm
PCB Pami
FIPATECH/CDFR26_PAMI
Open source firmware and PCB for a differential mobile robot (PAMI) based on ESP32-S3 - Coupe de France de Robotique
25 parts6 - 2 layers106.4 × 74.7 mm
Car pcb
MaximTrofimov/STM32-RC-Car
Designed two custom PCBs (remote and car) for a wirelessly-controlled RC car. Implemented wireless communication between two STM32 microcontrollers using embedded firmware.
55 parts1MIT - 2 layers117.1 × 68.6 mm
Proyecto exposito
misaacastillo/RoboticArm
“Robotic Arm” es un brazo robotico el cual cuenta con un modelo dummy de menores dimensiones. Este modelo copia tendrá una conexión entre sus potenciómetros y los servomotores ubicados en el modelo principal.
37 parts1 - 4 layers50 × 50 mm
Board v1
ductomn/Swarm-robot
Bachelor Thesis - Design and implementation of a cooperative robotic platform with simple communication
79 parts - 6 layers100 × 160 mm
Scopefun v2
snhobbs/scopefun-hardware
This repository contains Scopefun hardware schematics and pcb layout files.
840 parts - 2 layers68.6 × 53.3 mm
ENEL200ShieldGroup01
TheBroKendrick/Arduino-Turtle-Robot-
A project made in my First Professional Year of Electrical Engineering. This was made in collaboration with two other people and focussed on the basics of PCB design, 3D modelling, and basic embedded software…
41 parts
Questions
How big is the Auto Headlight Control System PCB?
It measures 72.4 × 73.7 mm and has 2 copper layers, 1.6 mm thick.
What parts does the Auto Headlight Control System use?
20 parts, built around the SN65HVD230D, ADXL345-EP, AP3216SGC and SG90. The full list of its parts is on this page, with links to each part's symbol and footprint where PCBKit's library has them.
Where can I download the Auto Headlight Control System KiCad files?
From the kmkim036/Auto-Headlight-Control-System repository on GitHub, at the commit this page was made from: the board is circuit/auto-headlight-control-system/auto-headlight-control-system.kicad_pcb. PCBKit opens the board in the browser, with nothing to install.
Can I use the Auto Headlight Control System design in my own project?
Its repository states no licence, so its author keeps all rights: ask kmkim036 before reusing the design.