
Remote pcb
MaximTrofimov/STM32-RC-Car
Designed two custom PCBs (remote and car) for a wirelessly-controlled RC car. Implemented wireless communication between two STM32 microcontrollers using embedded firmware.

Designed two custom PCBs (remote and car) for a wirelessly-controlled RC car. Implemented wireless communication between two STM32 microcontrollers using embedded firmware. Developed manual and autonomous operation modes.
Car pcb is an open-source printed circuit board by MaximTrofimov, from the MaximTrofimov/STM32-RC-Car repository on GitHub, published under the MIT licence. It is a 2-layer board of 106.4 × 74.7 mm with 55 parts on 71 nets, routed with 650 tracks and 106 vias.
It is built around the STM32F446RET6, NRF24L01 and SG90. Its parts include 24 capacitors, 11 resistors, 11 connectors, 3 ICs and 1 inductor. It belongs with the STM32 boards of this library.
RC car with manual and autonomous modes, dual STM32 wireless communication (remote and car PCBs).
Manual Mode
Autonomous Mode
RC Car and Remote
Remote and Car PCBs
Firmware/
car_mcu/ - STM32 embedded firmware for the car MCU
remote_mcu/ - STM32 embedded firmware for the remote MCU
Hardware/
car_pcb/ - Car PCB, schematic, BOM
remote_pcb/ - Remote PCB, schematic, BOM
Mechanical/ - Wheels and steering servo enclosure CAD files (STEP)Manual Mode: The X and Y coordinates of the joystick position are read into a two variable array, VR. The array is then transmitted alongside each packet using the remote PCB's NRF24L01 module, and received at the car PCB's NRF24L01 module. The DC Motors are controlled using the TB6612FNG where a maximum joystick value results in fully duty cycle, a neutral results in zero duty cycle, and a minimum results in maximum duty cycle spinning the motors the other way. The SG90 steering is controlled via a timer for PWM. If the joystick is extended to the far right or far left, the NRF24L01 sends a larger joystick value and therefore the pulse is set to high for longer. Both throttle and steering respond to the specific displacement of the joystick from its absolute center, giving it the ability to control speed, and steering degree. The firmware dictates what part of the packet is responsible for motors, what part for the steering angle, and what part for the mode, which is triggered via an interrupt.
Autonomous Mode: If the joystick button is pressed, the mode is toggled to autonomous. Motors begin by running on half duty cycle and steering is set to a constant of about 20 degrees. The front, left, and right ultrasonic sensors notify the microcontroller when an obstacle is a certain distance away. Once this happens the car stops, checks its sides, goes back, and turns to the side where there is more free space.
Car MCU
Remote MCU
Car PCB
Remote PCB
Car PCB
Remote PCB
| Qty | Value | Footprint | References |
|---|---|---|---|
| 9 | 100n | Capacitor_SMD:C_0805_2012Metric | C1, C2, C3, C4, C5, C9, C11, C12, C15 |
| 5 | 10u | Capacitor_SMD:C_0805_2012Metric | C6, C14, C18, C21, C24 |
| 4 | MountingHole | MountingHole:MountingHole_2.2mm_M2 | H1, H2, H3, H4 |
| 3 | 100k | Resistor_SMD:R_0805_2012Metric | R8, R9, R11 |
| 3 | 1k | Resistor_SMD:R_0805_2012Metric | R2, R4, R6 |
| 3 | 2k | Resistor_SMD:R_0805_2012Metric | R3, R5, R7 |
| 2 | 100u | Capacitor_THT:C_Radial_D5.0mm_H11.0mm_P2.00mm | C16, C17 |
| 2 | 47u | Capacitor_THT:C_Radial_D5.0mm_H11.0mm_P2.00mm | C13, C23 |
| 1 | 10k | Resistor_SMD:R_0805_2012Metric | R1 |
| 1 | 10n | Capacitor_SMD:C_0805_2012Metric | C7 |
| 1 | 1u | Capacitor_SMD:C_0805_2012Metric | C8 |
| 1 | 2.2u | VLS3012CX-2R2M-1:IND_VLS3012CX-2R2M-1 | L1 |
| 1 | 22u | Capacitor_SMD:C_0805_2012Metric | C20 |
| 1 | 390p | Capacitor_SMD:C_0805_2012Metric | C19 |
| 1 | 4.7u | Capacitor_SMD:C_0805_2012Metric | C10 |
| 1 | 430p | Capacitor_SMD:C_0805_2012Metric | C22 |
| 1 | 523k | Resistor_SMD:R_0805_2012Metric | R10 |
| 1 | DC Motors | Connector_PinHeader_2.54mm:PinHeader_1x04_P2.54mm_Vertical | J5 |
| 1 | HC-SR04 F | Connector_PinHeader_2.54mm:PinHeader_1x04_P2.54mm_Vertical | J6 |
| 1 | HC-SR04 L | Connector_PinHeader_2.54mm:PinHeader_1x04_P2.54mm_Vertical | J12 |
| 1 | HC-SR04 R | Connector_PinHeader_2.54mm:PinHeader_1x04_P2.54mm_Vertical | J13 |
| 1 | LOGO | LOGO | G*** |
| 1 | LiPo Battery 7.4V | Connector_PinHeader_2.54mm:PinHeader_1x02_P2.54mm_Vertical | J9 |
| 1 | NRF24L01 | Connector_PinHeader_2.54mm:PinHeader_2x04_P2.54mm_Vertical | J3 |
| 1 | SG90 | Connector_PinHeader_2.54mm:PinHeader_1x03_P2.54mm_Vertical | J7 |
| 1 | STM32F446RET6 | Package_QFP:LQFP-64_10x10mm_P0.5mm | U1 |
| 1 | SWD | Connector_PinHeader_2.54mm:PinHeader_1x04_P2.54mm_Vertical | J1 |
| 1 | TB6612FNG L | Connector_PinHeader_2.54mm:PinHeader_1x08_P2.54mm_Vertical | J14 |
| 1 | TB6612FNG R | Connector_PinHeader_2.54mm:PinHeader_1x08_P2.54mm_Vertical | J4 |
| 1 | TPS62152 3.3V | Package_DFN_QFN:VQFN-16-1EP_3x3mm_P0.5mm_EP1.68x1.68mm_ThermalVias | U2 |
| 1 | TPS82130 5V | Package_LGA:Texas_SIL0008D_MicroSiP-8-1EP_2.8x3mm_P0.65mm_EP1.1x1.9mm_ThermalVias | U3 |
| 1 | USART2 | Connector_PinHeader_2.54mm:PinHeader_1x04_P2.54mm_Vertical | J2 |

MaximTrofimov/STM32-RC-Car
Designed two custom PCBs (remote and car) for a wirelessly-controlled RC car. Implemented wireless communication between two STM32 microcontrollers using embedded firmware.

RoboticsBrno/Robutek
Robůtek je robotická platforma založená na čipu ESP32-S3. Je velice rozšitiřelný, ale ze základu umí jezdit, kreslit fixou, jezdit po čáře, pohybovat se bludištěm. Programování je přes Jaculus.

FIPATECH/CDFR26_PAMI
Open source firmware and PCB for a differential mobile robot (PAMI) based on ESP32-S3 - Coupe de France de Robotique


misaacastillo/RoboticArm
“Robotic Arm” es un brazo robotico el cual cuenta con un modelo dummy de menores dimensiones. Este modelo copia tendrá una conexión entre sus potenciómetros y los servomotores ubicados en el modelo principal.

ductomn/Swarm-robot
Bachelor Thesis - Design and implementation of a cooperative robotic platform with simple communication

snhobbs/scopefun-hardware
This repository contains Scopefun hardware schematics and pcb layout files.

TheBroKendrick/Arduino-Turtle-Robot-
A project made in my First Professional Year of Electrical Engineering. This was made in collaboration with two other people and focussed on the basics of PCB design, 3D modelling, and basic embedded software…

IshikawaRasoto/integration-workshop-3
Repository for the development of the project for the Integration Workshop 3 course.
It measures 106.4 × 74.7 mm and has 2 copper layers, 1.6 mm thick.
55 parts, built around the STM32F446RET6, NRF24L01 and SG90. The full list of its parts is on this page, with links to each part's symbol and footprint where PCBKit's library has them.
From the MaximTrofimov/STM32-RC-Car repository on GitHub, at the commit this page was made from: the board is Hardware/car_pcb/car_pcb.kicad_pcb and its schematic Hardware/car_pcb/car_pcb.kicad_sch. PCBKit opens the board in the browser, with nothing to install.
Its repository publishes it under the MIT licence: you may reuse it on that licence's terms (keep the author's notice, and for a copyleft licence share your changes alike).