

Rover vcu
- Size
- 86.3 × 44 mm
- Copper layers
- 4
- Thickness
- 1.6 mm
- Parts
- 101
- Nets
- 103
- Pads
- 371
- Tracks, vias
- 1,482, 203
- Pours
- 9
- Routed
- Yes
- KiCad
- KiCad 10.0 (file 20260206)
- Created
- 3 Jun 2026
- Updated
- 2 Sep 2026
Overview
Rover vcu is an open-source printed circuit board by jumper385, from the jumper385/rover-vcu repository on GitHub. It is a 4-layer board of 86.3 × 44 mm with 101 parts on 103 nets, routed with 1,482 tracks and 203 vias.
It is built around the SN65HVD230D, LAN8742A-CZ and NUP2105L, with the B5819W, TS-1088-AR02016 and USB4105-GF-A among its other parts. Its parts include 41 capacitors, 33 resistors, 6 ICs, 6 diodes and 5 connectors. It belongs with the robots and motor control boards and the STM32 boards of this library.
Main components
6SN65HVD230D
SOIC-8-40℃~+85℃ 1 17mA 1Mbps 370uA 3V~3.6V CAN Transceiver Low-power mode、Wake-up function、ESD protection、Thermal shutdown protection、Bus fault protection、Hot-swap protection SOIC-8 CAN Transceivers ROHSTexas InstrumentsCAN TransceiversLAN8742A-CZ
QFN-24-EP(4x4)0℃~+70℃ 1.8V~3.3V 10BASE-T、100BASE-TX 10Mbit/s、100Mbit/s Ethernet Transceiver RMII QFN-24-EP(4x4) Ethernet Transceivers ROHSMicrochip TechnologyEthernet TransceiversNUP2105L
SOT-23-55℃~+150℃ 100nA 2 24V 30pF 32V 350W@8/20us 44V 8A@8/20us Bidirectional IEC 61000-4-2、IEC 61000-4-5、IEC 61000-4-4 TVS SOT-23 ESD and Surge Protection (TVS/ESD) ROHSonsemiESD And Surge Protection (TVS/ESD)B5819W
SOD-123-55℃~+125℃ 1.5A 1mA@40V 25A 40V 600mV@1A Standalone SOD-123 Schottky Diodes ROHSMDDSchottky DiodesTS-1088-AR02016
SMD,4x3mm-30℃~+80℃ 1.6N 100,000 cycles 12V 2mm 3.9mm 3mm 50mA Black Round Button SMD(SMT) Tab SPST Surface Mount,Vertical Without Bracket SMD,4x3mm Tactile Switches ROHSXUNPUTactile SwitchesUSB4105-GF-A
SMD-40℃~+85℃ 1 12P 48V 5A Black Female Surface Mount, Right Angle Type-C USB 2.0 SMD USB Connectors ROHSGlobal Connector Technology (GCT)USB Connectors
Parts
101| Qty | Value | Footprint | References |
|---|---|---|---|
| 16 | 100nF | chenry-footprint-lib:C_0402 | C3, C4, C5, C6, C9, C10, C16, C17, C18, C23, C24, C25, C31, C35, C38, C40 |
| 14 | 10K | chenry-footprint-lib:R_0402 | R3, R4, R5, R6, R7, R8, R9, R10, R18, R19, R23, R24, R25, R31 |
| 5 | 5K1 | chenry-footprint-lib:R_0402 | R1, R2, R20, R21, R22 |
| 4 | 1pF | chenry-footprint-lib:C_0402 | C32, C33, C36, C37 |
| 4 | 1uF | chenry-footprint-lib:C_0402 | C19, C39, C44, C45 |
| 4 | 33R | chenry-footprint-lib:R_0402 | R14, R15, R16, R17 |
| 4 | 4.7uF | chenry-footprint-lib:C_0402 | C7, C8, C30, C34 |
| 4 | 49.9R | chenry-footprint-lib:R_0402 | R27, R28, R29, R30 |
| 4 | MountingHole | MountingHole:MountingHole_3.2mm_M3 | H2, H4, H5, H6 |
| 3 | 22uF | Capacitor_SMD:C_0603_1608Metric | C41, C42, C43 |
| 3 | LED_RED_0603 | LED_SMD:LED_0603_1608Metric | D4, D5, D6 |
| 2 | 10pF | chenry-footprint-lib:C_0402 | C11, C12 |
| 2 | 120R | chenry-footprint-lib:R_0402 | R12, R13 |
| 2 | 2.2uF | chenry-footprint-lib:C_0402 | C1, C2 |
| 2 | 20pF | chenry-footprint-lib:C_0402 | C21, C22 |
| 2 | 330R | chenry-footprint-lib:R_0402 | R32, R33 |
| 2 | 6pF | chenry-footprint-lib:C_0402 | C13, C14 |
| 2 | NUP2105L | Package_TO_SOT_SMD:SOT-23 | D1, D2 |
| 2 | SN65HVD230 | Package_SO:SOIC-8_3.9x4.9mm_P1.27mm | U4, U5 |
| 1 | 100pF | chenry-footprint-lib:C_0402 | C20 |
| 1 | 10uF | chenry-footprint-lib:C_0402 | C15 |
| 1 | 12.1K | chenry-footprint-lib:R_0402 | R26 |
| 1 | 15uH | Inductor_SMD:L_Sunlord_SWPA5040S | L1 |
| 1 | 25MHz | Crystal:Crystal_SMD_3225-4Pin_3.2x2.5mm | XTAL2 |
| 1 | 32.768kHz | Crystal:Crystal_SMD_3215-2Pin_3.2x1.5mm | Y1 |
| 1 | 430450400 | Connector_Molex:Molex_Micro-Fit_3.0_43045-0400_2x02_P3.00mm_Horizontal | J3 |
| 1 | 430451200 | Connector_Molex:Molex_Micro-Fit_3.0_43045-1200_2x06_P3.00mm_Horizontal | J6 |
| 1 | 56K | chenry-footprint-lib:R_0402 | R11 |
| 1 | 600Ohm @ 100MHz | Capacitor_SMD:C_0603_1608Metric | FB1 |
| 1 | 8MHz | Crystal:Crystal_SMD_5032-2Pin_5.0x3.2mm | XTAL1 |
| 1 | B5819W | Diode_SMD:D_SOD-123 | D3 |
| 1 | Conn_ST_STDC14 | Connector_PinHeader_1.27mm:PinHeader_2x07_P1.27mm_Vertical_SMD | J1 |
| 1 | LAN8742A | chenry-footprint-lib:VQFN-24-1EP_4x4mm_P0.5mm_EP2.5x2.5mm_ThermalVias | U2 |
| 1 | LMR51610 | Package_TO_SOT_SMD:SOT-23-6 | U6 |
| 1 | NCP1117-3.3_SOT223 | Package_TO_SOT_SMD:SOT-223-3_TabPin2 | U8 |
| 1 | RJ45_Hanrun_HR911105A_Horizontal | chenry-footprint-lib:RJ45_Hanrun_HR911105A_Horizontal | J4 |
| 1 | STM32H563RITx | Package_QFP:LQFP-64_10x10mm_P0.5mm | U1 |
| 1 | TS-1088-AR02016 | Button_Switch_SMD:SW_SPST_TS-1088-xR020 | SW1 |
| 1 | USB4105-GF-A | Connector_USB:USB_C_Receptacle_GCT_USB4105-xx-A_16P_TopMnt_Horizontal | J2 |
Similar boards
- 4 layers250.8 × 30 mm

- 4 layers85 × 85 mm

- 4 layers110 × 80 mm

PNP MOBO V2
GabrielD98/PickUS_and_PlacUS
pick and place de PCB pour projet S4 de robotique
126 parts5MIT - 2 layers

GCAN gauge
willemcvu/gCAN-gauge
An open-source ESP32-based programmable digital gauge targeted at EV conversions
49 parts4MIT - 2 layers100 × 80 mm

Meganecan gw
Barbedx/MeganeCAN
ESP32-based CAN-bus companion for Renault Megane 2 infotainment displays.
68 parts3 - 2 layers68 × 92 mm

JoeM BMC V3.2
JoeMudr/JoeMBMC
This project is derived from Toms SimpBMS code. It started as a clone (Software & Hardware) but ended up completely rewritten and redesigned. But you might still find some traces to the original code.
70 parts2MIT - 4 layers71.2 × 66.1 mm

Maxbox
ios-cv/maxbox
An in car telemetry and access management box consisting of PCB design, firmware and case.
110 parts1AGPL-3.0 - 2 layers74 × 32 mm

Questions
How big is the Rover vcu PCB?
It measures 86.3 × 44 mm and has 4 copper layers, 1.6 mm thick.
What parts does the Rover vcu use?
101 parts, built around the SN65HVD230D, LAN8742A-CZ, NUP2105L and B5819W. The full list of its parts is on this page, with links to each part's symbol and footprint where PCBKit's library has them.
Where can I download the Rover vcu KiCad files?
From the jumper385/rover-vcu repository on GitHub, at the commit this page was made from: the board is Rover VCU.kicad_pcb and its schematic Rover VCU.kicad_sch. PCBKit opens the board in the browser, with nothing to install.
Can I use the Rover vcu design in my own project?
Its repository states no licence, so its author keeps all rights: ask jumper385 before reusing the design.