

GCAN gauge
An open-source ESP32-based programmable digital gauge targeted at EV conversions
- Copper layers
- 2
- Thickness
- 1 mm
- Parts
- 49
- Nets
- 40
- Pads
- 232
- Tracks, vias
- 623, 90
- Pours
- 2
- Routed
- Yes
- KiCad
- KiCad 5 (file 20171130)
- Created
- 20 Jul 2021
- Updated
- 22 Aug 2021
Overview
GCAN gauge is an open-source printed circuit board by willemcvu, from the willemcvu/gCAN-gauge repository on GitHub, published under the MIT licence. It is a 2-layer board with 49 parts on 40 nets, routed with 623 tracks and 90 vias.
It is built around the CP2102N-A01-GQFN28R, ESP32-WROOM-32 and SN65HVD230D, with the AP1509-33SG-13-MS, CPC1017N and SS8050-G among its other parts. Its parts include 14 resistors, 8 capacitors, 6 diodes, 5 ICs and 3 transistors. It belongs with the ESP32 boards of this library.
Main components
9CP2102N-A01-GQFN28R
QFN-28-EP(5x5)-40℃~+85℃ 13.7mA 195uA 3Mbps 3V~3.6V Transceiver USB 2.0 QFN-28-EP(5x5) USB Converters ROHSSilicon LabsUSB ConvertersESP32-WROOM-32
SMD,18x25.5mm-40℃~+85℃ -98dBm 2.4GHz 2.7V~3.6V 20dBm Bluetooth4.2 ESP32-DOWDQ6 UART、SDIO、SPI、I2C、GPIO、PWM、ADC、DAC SMD,25.5x18mm WiFi Modules ROHSEspressif SystemsWiFi ModulesSN65HVD230D
SOIC-8-40℃~+85℃ 1 17mA 1Mbps 370uA 3V~3.6V CAN Transceiver Low-power mode、Wake-up function、ESD protection、Thermal shutdown protection、Bus fault protection、Hot-swap protection SOIC-8 CAN Transceivers ROHSTexas InstrumentsCAN TransceiversAP1509-33SG-13-MS
SOP-8SOP-8 DC-DC Converters ROHSMSKSEMIDC-DC ConvertersCPC1017N
SOP-4-2.54mm1.2V 1.5kV 100mA 10ms 10ms 16Ω 60V One set normally open: 2A (SPST - normally open) SOP-4-2.54mm Solid State Relays (MOS Output) ROHSLittelfuse/IXYSSolid State Relays (MOS Output)SS8050-G
SOT-231 NPN 1.5A 100 100MHz 100nA 25V 300mW 400mV 5V NPN SOT-23 Bipolar (BJT) ROHSComchipBipolar (BJT)CM1293A-04SO
SC-74-40℃~+85℃ 1A@8/20us 1uA 2pF 3.3V 9.9V ESD Four channels IEC 61000-4-2 SC-74 ESD and Surge Protection (TVS/ESD) ROHSonsemiESD And Surge Protection (TVS/ESD)DR331-513AE
SMD-40℃~+135℃ 2 250V 300mΩ 42V 500mA 51uH@100kHz 80V SMD Common Mode Filters ROHSBournsCommon Mode FiltersNUP2105L
SOT-23-55℃~+150℃ 100nA 2 24V 30pF 32V 350W@8/20us 44V 8A@8/20us Bidirectional IEC 61000-4-2、IEC 61000-4-5、IEC 61000-4-4 TVS SOT-23 ESD and Surge Protection (TVS/ESD) ROHSonsemiESD And Surge Protection (TVS/ESD)
README
README.mdgCAN-gauge
An open-source ESP32-based programmable digital gauge targeted at EV conversions
See some previews of mechanical stuff and BOM costing here: https://imgur.com/gallery/dh8G9dV/comment/2116424201
Parts
49| Qty | Value | Footprint | References |
|---|---|---|---|
| 5 | 10k | Resistor_SMD:R_0603_1608Metric | R3, R7, R12, R13, R14 |
| 4 | 0.1uF | Capacitor_SMD:C_0603_1608Metric | C1, C5, C6, C7 |
| 4 | M2 | MountingHole:MountingHole_2.1mm | H1, H2, H3, H4 |
| 3 | 10uF | Capacitor_SMD:C_0805_2012Metric | C3, C4, C8 |
| 3 | 30V 1A | Diode_SMD:D_SMA | D3, D4, D6 |
| 3 | SS8050-G | Package_TO_SOT_SMD:SOT-23 | Q1, Q2, Q3 |
| 2 | 5.1k | Resistor_SMD:R_0603_1608Metric | R1, R2 |
| 1 | 10R | Resistor_SMD:R_0603_1608Metric | R8 |
| 1 | 10uF | Capacitor_SMD:C_1210_3225Metric | C2 |
| 1 | 120R | Resistor_SMD:R_0603_1608Metric | R5 |
| 1 | 1k | Resistor_SMD:R_0603_1608Metric | R6 |
| 1 | 22.1k | Resistor_SMD:R_0603_1608Metric | R9 |
| 1 | 2k | Resistor_SMD:R_0603_1608Metric | R11 |
| 1 | 400R | Resistor_SMD:R_0603_1608Metric | R4 |
| 1 | 47.5k | Resistor_SMD:R_0603_1608Metric | R10 |
| 1 | 47uH | main-board-custom-footprints:L_Taiyo-Yuden_NR-60xx | L1 |
| 1 | 824501131 | Diode_SMD:D_SMA | D2 |
| 1 | AP1509-33SG-13 | main-board-custom-footprints:SO-8_3.9x4.9mm_P1.27mm | U3 |
| 1 | BOOT jumper | Jumper:SolderJumper-2_P1.3mm_Open_RoundedPad1.0x1.5mm | JP2 |
| 1 | CM1293A-04SO | Package_TO_SOT_SMD:SOT-23-6 | D1 |
| 1 | CP2102N-A01-GQFN28 | Package_DFN_QFN:QFN-28-1EP_5x5mm_P0.5mm_EP3.35x3.35mm | U4 |
| 1 | CPC1017N | Package_SO:SOP-4_3.8x4.1mm_P2.54mm | U2 |
| 1 | DR331-513AE | main-board-custom-footprints:COMMON_MODE_CHOKE_BOURNS_DR331 | FL1 |
| 1 | EN jumper | Jumper:SolderJumper-2_P1.3mm_Open_RoundedPad1.0x1.5mm | JP1 |
| 1 | ESP32-WROOM-32 | RF_Module:ESP32-WROOM-32 | U5 |
| 1 | FRONT_BUTTON | main-board-custom-footprints:SW_SPST_PTS810 | SW1 |
| 1 | JST JWPF | main-board-custom-footprints:JST_JWPF_B04B-JWPF-SK-R_1x04_P2.00mm_Vertical | J2 |
| 1 | LCD_FFC_SOLDER | main-board-custom-footprints:LCD_ROUND_IPS_ER-TFT1.28-1 | J3 |
| 1 | LOGO | main-board-custom-footprints:gcan-gauge-github-link-qr | G1 |
| 1 | NUP2105L | Package_TO_SOT_SMD:SOT-23 | D5 |
| 1 | SN65HVD230 | Package_SO:SOIC-8_3.9x4.9mm_P1.27mm | U1 |
| 1 | USB-C Receptacle | main-board-custom-footprints:USB_C_Receptacle_JAE_DX07S024WJ3R400 | J1 |
Similar boards
- 2 layers48 × 42 mm

- 6 layers236 × 150 mm

- 2 layers37.9 × 15.2 mm

- 4 layers64.5 × 68.3 mm

- 2 layers28.5 × 53.6 mm

- 2 layers70.6 × 66.3 mm

Prototype Rev-
DiegoBriceno03/Portable-Biofeedback
Portable Biofeedback device for anxiety management
106 parts3 - 2 layers100 × 100 mm

PLC ESP32
sea2-dsi-fceia/PLACA_IOT_INDUSTRIAL
Placa de desarrollo para aplicaciones industriales IoT basada en ESP32 (Open Source)
148 parts1 - 4 layers54 × 38 mm

Esp32 energy monitor
rdalla/proj_kicad_esp32_energy_consumption
The project is a energy monitoring module. It is based on ESP32 with current sensor (sct-013 50A/1V).
54 parts
Questions
What parts does the GCAN gauge use?
49 parts, built around the CP2102N-A01-GQFN28R, ESP32-WROOM-32, SN65HVD230D and AP1509-33SG-13-MS. The full list of its parts is on this page, with links to each part's symbol and footprint where PCBKit's library has them.
Where can I download the GCAN gauge KiCad files?
From the willemcvu/gCAN-gauge repository on GitHub, at the commit this page was made from: the board is hardware/main-board/main-board.kicad_pcb. PCBKit opens the board in the browser, with nothing to install.
Can I use the GCAN gauge design in my own project?
Its repository publishes it under the MIT licence: you may reuse it on that licence's terms (keep the author's notice, and for a copyleft licence share your changes alike).