
Temperature logger
H-S-S-11/attiny-temperature-logger
Temperature logger using a RTC, EEPROM, and Temperature sensor controled over I2C by an ATTiny

The Mender Shield illustrates the capability to run a Mender client on heterogeneous platforms
Mender shield is an open-source printed circuit board by joelguittet, from the joelguittet/mender-shield repository on GitHub, published under the Apache-2.0 licence. It is a 2-layer board of 65 × 59 mm with 54 parts on 90 nets, routed with 1,156 tracks and 95 vias.
It is built around the ARDUINO UNO R3, 24FC512-I/P and AT24CS32-STUM-T, with the ATECC608B-SSHDA-T and KTD2058 among its other parts. Its parts include 18 diodes, 5 capacitors, 5 resistors, 5 ICs and 1 connector. It belongs with the AVR (ATmega, ATtiny) boards of this library.
The Mender Shield illustrates the capability to run a Mender client on heterogeneous platforms such as RaspberryPi (Linux based) and MCUs (RTOS/bare metal).
The following picture shows the Mender devices in the field with the mender-shield on the front, RaspberryPi and ESP32 platforms in the back:

The following picture shows both sides of the mender-shield:

Mender MCU client is an open source over-the-air (OTA) library updater for MCU devices. Check-out the source and demonstration examples!
The project has been created with Kicad, you can browse the project on KiCanvas. Gerber files used to manufacture the board are provided.
The software supports includes a script to perform a very simple demonstration on Raspberry Pi 3 device and an ESP-IDF based application used with the Wemos D1 r32 ESP32-based evaluation board.
Copyright joelguittet and mender-mcu-client contributors
Licensed under the Apache License, Version 2.0 (the "License"); you may not use this file except in compliance with the License. You may obtain a copy of the License at
http://www.apache.org/licenses/LICENSE-2.0Unless required by applicable law or agreed to in writing, software distributed under the License is distributed on an "AS IS" BASIS, WITHOUT WARRANTIES OR CONDITIONS OF ANY KIND, either express or implied. See the License for the specific language governing permissions and limitations under the License.
| Qty | Value | Footprint | References |
|---|---|---|---|
| 18 | Inolux_IN-P55TATRGB | LED_SMD:LED_Inolux_IN-P55TATRGB_PLCC6_5.0x5.5mm_P1.8mm | D1, D2, D3, D4, D5, D6, D7, D10, D11, D12, D13, D14, D15, D16, D17, D18 +2 |
| 5 | 3.3k | Resistor_SMD:R_0805_2012Metric | R1, R2, R3, R4, R5 |
| 5 | SolderJumper_3_Bridged12 | Jumper:SolderJumper-3_P1.3mm_Bridged12_RoundedPad1.0x1.5mm_NumberLabels | JP1, JP2, JP3, JP4, JP5 |
| 4 | MountingHole | MountingHole:MountingHole_2.7mm_M2.5_DIN965 | H1, H2, H3, H4 |
| 3 | 100nF | Capacitor_SMD:C_0805_2012Metric | C3, C4, C5 |
| 2 | 10µF | Capacitor_SMD:C_0805_2012Metric | C1, C2 |
| 2 | LOGO | Project:Mender-Logo_12x12mm_Silkscreen | G***, G*** |
| 1 | 24FC512 | Package_SO:SOIC-8_3.9x4.9mm_P1.27mm | U4 |
| 1 | AT24CS32-STUM | Package_TO_SOT_SMD:SOT-23-5 | U3 |
| 1 | ATECC608B-SSHDA | Package_SO:SOIC-8_3.9x4.9mm_P1.27mm | U5 |
| 1 | Arduino_UNO_R3 | Module:Arduino_UNO_R3 | A1 |
| 1 | ID_WP | TestPoint:TestPoint_Pad_D1.5mm | TP1 |
| 1 | KTD2058 | Package_DFN_QFN:UQFN-20-1EP_3x3mm_P0.4mm_EP1.7x1.7mm_ThermalVias | U2 |
| 1 | KTD2061 | Package_DFN_QFN:UQFN-20-1EP_3x3mm_P0.4mm_EP1.7x1.7mm_ThermalVias | U1 |
| 1 | LOGO | Project:Trust-Logo_6x6mm_SilkScreen | ATECC608B |
| 1 | Raspberry_Pi_2_3 | Connector_PinSocket_2.54mm:PinSocket_2x20_P2.54mm_Vertical | J1 |
The 48 most common of 54 parts.

H-S-S-11/attiny-temperature-logger
Temperature logger using a RTC, EEPROM, and Temperature sensor controled over I2C by an ATTiny

UofA-SPEAR/pcb_designs_2026
Repository for SPEAR 2026 PCB designs. PCB design software is KiCad.

myriadrf/reference-development-kit
The Myriad-RF Reference Hardware design files and firmware

OnionDAO-git/oniondao-badge
An open-source, hacker-conference-style electronic badge built around the ESP32-S3-WROOM-1-N8R8 (8 MB flash + 8 MB Octal PSRAM), with swappable RF / audio / storage modules, an e-paper (or TFT) display socket, a secure…


rein-baremetal/REIN_R1_KiCad
Dual-MCU baremetal embedded development board featuring high-speed QSPI storage, hardware USB hub, and flexible power management. Open for PCB trace routing collaboration

Kampi/IoT-Gateway
Open-Source Zigbee, Thread, wM-Bus, LoRa, LoRaWAN gateway for Home Assistant.

It measures 65 × 59 mm and has 2 copper layers, 1.6 mm thick.
54 parts, built around the ARDUINO UNO R3, 24FC512-I/P, AT24CS32-STUM-T and ATECC608B-SSHDA-T. The full list of its parts is on this page, with links to each part's symbol and footprint where PCBKit's library has them.
From the joelguittet/mender-shield repository on GitHub, at the commit this page was made from: the board is hardware/mender-shield.kicad_pcb and its schematic hardware/mender-shield.kicad_sch. PCBKit opens the board in the browser, with nothing to install.
Its repository publishes it under the Apache-2.0 licence: you may reuse it on that licence's terms (keep the author's notice, and for a copyleft licence share your changes alike).