

Self Balancing Robot
This project is still in development !!!
- Size
- 72.8 × 44.8 mm
- Copper layers
- 2
- Thickness
- 1.6 mm
- Parts
- 31
- Nets
- 36
- Pads
- 123
- Tracks, vias
- 1, 0
- Routed
- Yes
- KiCad
- KiCad 8.0 (file 20240108)
- Created
- 1 Apr 2025
- Updated
- 12 Feb 2026
Overview
Self Balancing Robot is an open-source printed circuit board by Joanna610, from the Joanna610/Self-Balancing-Robot repository on GitHub. It is a 2-layer board of 72.8 × 44.8 mm with 31 parts on 36 nets, routed with 1 track and 0 vias.
It is built around the ATMEGA328P-AU and LP2985-33DBV. Its parts include 11 capacitors, 9 connectors, 4 resistors, 3 ICs and 2 diodes. It belongs with the robots and motor control boards and the AVR (ATmega, ATtiny) boards of this library.
Main components
2ATMEGA328P-AU
TQFP-32(7x7)-40℃~+85℃ 1.8V~5.5V 10bit 1KB 20MHz 23 2KB 32KB 8 Bit AVR Built-in FLASH TQFP-32(7x7) Microcontrollers (MCU/MPU/SOC) ROHSMicrochip TechnologyMicrocontrollers (MCU/MPU/SOC)LP2985-33DBV
SOT-23-5-40℃~+125℃@(Tj) 1 150mA 16V 3.3V 30uVrms 45dB@(1kHz) 575mV@(150mA) 850uA Fixed Over Current Protection、Short Circuit Protection、Thermal shutdown、Enable control、Noise bypass terminal Positive SOT-23-5 Voltage Regulators - Linear, Low Drop Out (LDO) Regulators ROHSTexas InstrumentsVoltage Regulators - Linear, Low Drop Out (LDO) Regulators
README
README.mdSelf_Balancing_Robot
This project is still in development !!!
The projects include code for Arduino. It collects data from the acceleromiter MPU6050 and modifies them accordingly. The code also turn on and off the motors with PWM. It can do this thanks to H bridge - L293D. The robot try to stabilize itself due to implemented PID algorithm.
Parts
31| Qty | Value | Footprint | References |
|---|---|---|---|
| 8 | 100nF | Capacitor_SMD:C_0805_2012Metric | C1, C2, C3, C4, C6, C7, C8, C14 |
| 2 | 4.7k | Resistor_SMD:R_0805_2012Metric | R4, R5 |
| 2 | 47uF | Capacitor_SMD:C_0805_2012Metric | C12, C13 |
| 1 | 10k | Resistor_SMD:R_0805_2012Metric | R1 |
| 1 | 1uF | Capacitor_SMD:C_0805_2012Metric | C5 |
| 1 | 330 | Resistor_SMD:R_0805_2012Metric | R3 |
| 1 | ATmega328P-A | Package_QFP:TQFP-32_7x7mm_P0.8mm | U1 |
| 1 | Analog | Connector_PinSocket_2.54mm:PinSocket_1x06_P2.54mm_Vertical | J2 |
| 1 | Crystal | Crystal:Crystal_HC49-4H_Vertical | Y1 |
| 1 | D_Schottky | Resistor_THT:R_Axial_DIN0207_L6.3mm_D2.5mm_P7.62mm_Horizontal | D1 |
| 1 | I2C | Connector_PinSocket_2.54mm:PinSocket_1x05_P2.54mm_Vertical | J1 |
| 1 | L293D_left | Connector_PinSocket_2.54mm:PinSocket_1x08_P2.54mm_Vertical | J5 |
| 1 | L293D_right | Connector_PinSocket_2.54mm:PinSocket_1x08_P2.54mm_Vertical | J8 |
| 1 | LED | LED_SMD:LED_1206_3216Metric | D3 |
| 1 | LP2985-3.3 | Package_TO_SOT_SMD:SOT-23-5 | U4 |
| 1 | NCP1117-5.0_SOT223 | Package_TO_SOT_SMD:SOT-223-3_TabPin2 | U5 |
| 1 | SPI | Connector_PinSocket_2.54mm:PinSocket_1x07_P2.54mm_Vertical | J10 |
| 1 | SW_Push | Button_Switch_THT:SW_PUSH_1P1T_6x3.5mm_H5.0_APEM_MJTP1250 | SW1 |
| 1 | UART | Connector_PinHeader_2.54mm:PinHeader_1x04_P2.54mm_Vertical | J7 |
| 1 | input_supply | Connector_TE-Connectivity:TE_826576-2_1x02_P3.96mm_Vertical | J9 |
| 1 | left_engine | Connector_TE-Connectivity:TE_826576-2_1x02_P3.96mm_Vertical | J3 |
| 1 | right_engine | Connector_TE-Connectivity:TE_826576-2_1x02_P3.96mm_Vertical | J4 |
Similar boards
- 2 layers50.5 × 128.5 mm

- 4 layers78 × 78 mm

- 4 layers150 × 55 mm

- 2 layers93 × 61 mm

- 4 layers60.6 × 100 mm

Theremin
adeboni/eurorack
This repository stores various eurorack module designs I've made
110 parts1GPL-3.0 - 2 layers84.5 × 56 mm

- 4 layers40.5 × 40.5 mm

- 2 layers36.5 × 56 mm

Questions
How big is the Self Balancing Robot PCB?
It measures 72.8 × 44.8 mm and has 2 copper layers, 1.6 mm thick.
What parts does the Self Balancing Robot use?
31 parts, built around the ATMEGA328P-AU and LP2985-33DBV. The full list of its parts is on this page, with links to each part's symbol and footprint where PCBKit's library has them.
Where can I download the Self Balancing Robot KiCad files?
From the Joanna610/Self-Balancing-Robot repository on GitHub, at the commit this page was made from: the board is PCB design/self_balancing_robot.kicad_pcb and its schematic PCB design/self_balancing_robot.kicad_sch. PCBKit opens the board in the browser, with nothing to install.
Can I use the Self Balancing Robot design in my own project?
Its repository states no licence, so its author keeps all rights: ask Joanna610 before reusing the design.