
Crawler pi charger
christianarrer/crawler-pi-hardware
Contains electronic PCB designs and 3D-printable parts for the crawler-pi autonomous tracked robot. Copy

Charging Board is an open-source printed circuit board by IanAntCosta, from the IanAntCosta/Charging-Board repository on GitHub. It is a 4-layer board of 150 × 55 mm with 146 parts on 139 nets, routed with 675 tracks and 138 vias.
It is built around the ATMEGA328P-AU, LTC4011CFE#PBF and FDS6975, with the LP2985-33DBV, 2N7002K and DMP4065S-13 among its other parts. Its parts include 56 resistors, 25 capacitors, 21 diodes, 13 ICs and 10 connectors. It belongs with the AVR (ATmega, ATtiny) boards of this library.
| Qty | Value | Footprint | References |
|---|---|---|---|
| 16 | 3k | Resistor_SMD:R_0603_1608Metric_Pad0.98x0.95mm_HandSolder | R3, R4, R5, R6, R14, R15, R17, R18, R27, R28, R30, R31, R40, R41, R43, R44 |
| 8 | 10k | Resistor_SMD:R_0603_1608Metric_Pad0.98x0.95mm_HandSolder | R1, R7, R20, R21, R33, R34, R46, R47 |
| 8 | 10u | Capacitor_THT:CP_Radial_D5.0mm_P2.00mm | C4, C5, C9, C10, C14, C15, C19, C20 |
| 6 | Screw_Terminal_01x02 | TerminalBlock_Phoenix:TerminalBlock_Phoenix_MKDS-1-2-3.81_1x02_P3.81mm_Horizontal | J3, J4, J5, J7, J8, J9 |
| 5 | 0.1u | Capacitor_SMD:C_0603_1608Metric_Pad1.08x0.95mm_HandSolder | C1, C6, C11, C16, C24 |
| 5 | RED | LED_SMD:LED_0603_1608Metric_Pad1.05x0.95mm_HandSolder | D4, D8, D13, D18, D21 |
| 4 | 100k | Resistor_SMD:R_0603_1608Metric_Pad0.98x0.95mm_HandSolder | R11, R19, R32, R45 |
| 4 | 100m | Resistor_SMD:R_0805_2012Metric_Pad1.20x1.40mm_HandSolder | R13, R23, R36, R49 |
| 4 | 10k | Connector_PinHeader_2.54mm:PinHeader_1x02_P2.54mm_Vertical | TH1, TH2, TH3, TH4 |
| 4 | 10uH | WE-LHMI_7050:WE-LHMI_7050 | L1, L2, L3, L4 |
| 4 | 20k | Resistor_SMD:R_0603_1608Metric_Pad0.98x0.95mm_HandSolder | R8, R16, R29, R42 |
| 4 | 22n | Capacitor_SMD:C_0603_1608Metric_Pad1.08x0.95mm_HandSolder | C3, C8, C13, C18 |
| 4 | 28k | Resistor_SMD:R_0603_1608Metric_Pad0.98x0.95mm_HandSolder | R9, R25, R38, R51 |
| 4 | 33n | Capacitor_SMD:C_0603_1608Metric_Pad1.08x0.95mm_HandSolder | C2, C7, C12, C17 |
| 4 | 51k | Resistor_SMD:R_0603_1608Metric_Pad0.98x0.95mm_HandSolder | R12, R24, R37, R50 |
| 4 | 9.76k | Resistor_SMD:R_0603_1608Metric_Pad0.98x0.95mm_HandSolder | R10, R26, R39, R52 |
| 4 | BLU | LED_SMD:LED_0603_1608Metric_Pad1.05x0.95mm_HandSolder | D3, D6, D11, D16 |
| 4 | Battery | TerminalBlock_Phoenix:TerminalBlock_Phoenix_MPT-0,5-2-2.54_1x02_P2.54mm_Horizontal | BT1, BT2, BT3, BT4 |
| 4 | GRN | LED_SMD:LED_0603_1608Metric_Pad1.05x0.95mm_HandSolder | D1, D9, D14, D19 |
| 4 | LTC4011CFE | Package_SO:HTSSOP-20-1EP_4.4x6.5mm_P0.65mm_EP2.74x3.86mm | U1, U2, U4, U5 |
| 4 | YEL | LED_SMD:LED_0603_1608Metric_Pad1.05x0.95mm_HandSolder | D2, D7, D12, D17 |
| 3 | 1k | Resistor_SMD:R_0603_1608Metric_Pad0.98x0.95mm_HandSolder | R53, R54, R55 |
| 2 | 150k | Resistor_SMD:R_0603_1608Metric_Pad0.98x0.95mm_HandSolder | R2, R22 |
| 2 | 1u | Capacitor_SMD:C_0603_1608Metric_Pad1.08x0.95mm_HandSolder | C22, C23 |
| 2 | 2N7002K | Package_TO_SOT_SMD:SOT-23 | Q2, Q4 |
| 2 | 6V | Diode_SMD:D_SOD-123F | D5, D10 |
| 2 | 6V | Diode_SMD:D_SOD-323_HandSoldering | D15, D20 |
| 2 | 70k | Resistor_SMD:R_0603_1608Metric_Pad0.98x0.95mm_HandSolder | R35, R48 |
| 2 | DMN3067LW-7 | Package_TO_SOT_SMD:SOT-323_SC-70 | Q11, Q12 |
| 2 | DMP4065S-13 | Package_TO_SOT_SMD:SOT-23 | Q1, Q3 |
| 2 | FDC658AP | Package_TO_SOT_SMD:SuperSOT-6 | Q9, Q10 |
| 2 | FDS6975 | Package_SO:SOIC-8_3.9x4.9mm_P1.27mm | U10, U11 |
| 2 | INA260 | Package_SO:TSSOP-16_4.4x5mm_P0.65mm | U7, U8 |
| 2 | Si4909DY-T1-GE3 | Package_SO:SOIC-8_3.9x4.9mm_P1.27mm | U12, U13 |
| 1 | 100n | Capacitor_SMD:C_0603_1608Metric_Pad1.08x0.95mm_HandSolder | C21 |
| 1 | 10uF | Capacitor_THT:CP_Axial_L10.0mm_D4.5mm_P15.00mm_Horizontal | C25 |
| 1 | 16MHz | Crystal:Resonator_Murata_DSN6-3Pin_W7.0mm_H2.5mm | Y1 |
| 1 | 1M | Resistor_SMD:R_0603_1608Metric_Pad0.98x0.95mm_HandSolder | R56 |
| 1 | ATmega328P-A | Package_QFP:TQFP-32_7x7mm_P0.8mm | U6 |
| 1 | Barrel_Jack_MountingPin | Connector_BarrelJack:BarrelJack_GCT_DCJ200-10-A_Horizontal | J10 |
| 1 | CD4050BPWR | Package_SO:SOIC-16_3.9x9.9mm_P1.27mm | U9 |
| 1 | Conn_01x03_Pin | Connector_PinHeader_2.54mm:PinHeader_1x03_P2.54mm_Vertical | J6 |
| 1 | Conn_02x03_Odd_Even | Connector_PinSocket_2.54mm:PinSocket_2x03_P2.54mm_Vertical | J1 |
| 1 | LP2985-3.3 | Package_TO_SOT_SMD:SOT-23-5 | U3 |
| 1 | Micro_SD_Card | Connector_Card:microSD_HC_Hirose_DM3BT-DSF-PEJS | J17 |

christianarrer/crawler-pi-hardware
Contains electronic PCB designs and 3D-printable parts for the crawler-pi autonomous tracked robot. Copy

lixiii/cauv-electronics
This is the electronics repository for our newest vehicle. This library is dependent on the Adam Greig KiCAD library. Additional components are added in the cauvlib directory.






adeboni/eurorack
This repository stores various eurorack module designs I've made
It measures 150 × 55 mm and has 4 copper layers, 1.6 mm thick.
146 parts, built around the ATMEGA328P-AU, LTC4011CFE#PBF, FDS6975 and LP2985-33DBV. The full list of its parts is on this page, with links to each part's symbol and footprint where PCBKit's library has them.
From the IanAntCosta/Charging-Board repository on GitHub, at the commit this page was made from: the board is ChargingBoard/ChargingBoard/ChargingBoard.kicad_pcb and its schematic ChargingBoard/ChargingBoard/ChargingBoard.kicad_sch. PCBKit opens the board in the browser, with nothing to install.
Its repository states no licence, so its author keeps all rights: ask IanAntCosta before reusing the design.