

Flight Computer V1
Flight computer pcb files
- Size
- 54.6 × 63.5 mm
- Copper layers
- 4
- Thickness
- 1.6 mm
- Parts
- 60
- Nets
- 78
- Pads
- 294
- Tracks, vias
- 454, 64
- Pours
- 4
- Routed
- Yes
- KiCad
- KiCad 9.0 (file 20241229)
- Created
- 12 Oct 2025
- Updated
- 17 Feb 2026
Overview
Flight Computer V1 is an open-source printed circuit board by jespinosa25, from the jespinosa25/Flight-Computer repository on GitHub. It is a 4-layer board of 54.6 × 63.5 mm with 60 parts on 78 nets, routed with 454 tracks and 64 vias.
It is built around the ESP32-S2-MINI-2-N4R2, MAX-M10M-00B and MMC5983MA, with the MS560702BA03-50, W25Q16JVSSIQ and BMI088 among its other parts. Its parts include 12 resistors, 9 capacitors, 6 ICs, 4 connectors and 3 diodes. It belongs with the ESP32 boards of this library.
Main components
6ESP32-S2-MINI-2-N4R2
SMD,20.5x15.4mm-40℃~+85℃ -97dBm 19.5dBm 2.4GHz 310mA 3V~3.6V 63mA ESP32-S2FN4R2 Chip On-board PCB Antenna Support USB interface UART、SPI、I2C、I2S、USB SMD,20.5x15.4mm WiFi Modules ROHSEspressif SystemsWiFi ModulesMAX-M10M-00B
SMD-18P-164dBm -40℃~+85℃ 1.8V~5.5V GPS、BeiDou、Galileo、GLONASS UART、I2C SMD-18P GNSS Modules ROHSu-bloxGNSS ModulesMMC5983MA
LGA-16(3x3)-40℃~+105℃ 18bit 2.8V~3.6V 450uA I2C、SPI ±8Gs ±8Gs LGA-16(3x3) 3D Magnetic Sensors ROHSMEMSIC3D Magnetic SensorsMS560702BA03-50
SMD-8P-40℃~+85℃ 1.5mbar 1.8V~3.6V 140nA 1Kpa~1.2bar I2C、SPI Yes SMD-8P Pressure Sensors ROHSTE ConnectivityPressure SensorsW25Q16JVSSIQ
SOIC-8-208mil-40℃~+85℃ 100,000 cycles 10uA 133MHz 16Mbit 2.7V~3.6V 20 Years 3ms SPI SOIC-8-208mil NOR FLASH ROHSWinbondNOR FLASHBMI088
LGA-16(3x4.5)-40℃~+85℃ Accelerometer Gyroscope LGA-16(3x4.5) Accelerometers ROHSBosch SensortecAccelerometers
Parts
60| Qty | Value | Footprint | References |
|---|---|---|---|
| 12 | TestPoint | TestPoint:TestPoint_Loop_D1.80mm_Drill1.0mm_Beaded | TP3, TP4, TP5, TP6, TP7, TP8, TP9, TP10, TP11, TP12, TP14, TP15 |
| 4 | 0.1uF | Capacitor_SMD:C_0201_0603Metric | C6, C7, C10, C11 |
| 4 | 100k | Resistor_SMD:R_0201_0603Metric | R5, R7, R9, R11 |
| 4 | MountingHole_Pad | MountingHole:MountingHole_2.5mm_Pad | H1, H2, H3, H4 |
| 2 | 10uF | Capacitor_SMD:C_0201_0603Metric | C5, C9 |
| 2 | 1k | Resistor_SMD:R_0201_0603Metric | R6, R10 |
| 2 | 1uF | Capacitor_SMD:C_0201_0603Metric | C4, C8 |
| 2 | 27k | Resistor_SMD:R_0201_0603Metric | R8, R12 |
| 2 | 50 | Resistor_SMD:R_0201_0603Metric | R2, R3 |
| 2 | Conn_01x04_Pin | 1725672:CONN_1725672_PXC | J1, J2 |
| 2 | NMOS | SI2302-TP:SOT-23_MCC | Q2, Q3 |
| 2 | TestPoint | TestPoint:TestPoint_Pad_D2.5mm | TP1, TP2 |
| 1 | 10k | Resistor_SMD:R_0201_0603Metric | R4 |
| 1 | 110 | Resistor_SMD:R_0201_0603Metric | R1 |
| 1 | 22uF | Capacitor_SMD:C_0201_0603Metric | C1 |
| 1 | BLUE | LED_SMD:LED_0201_0603Metric | D3 |
| 1 | BMI088 | BMI088:QFN_BMI085_BOS | U4 |
| 1 | Conn_01x06_Pin | Connector_PinSocket_2.54mm:PinSocket_1x06_P2.54mm_Vertical | J3 |
| 1 | Conn_02x04_Odd_Even | Connector_PinSocket_2.54mm:PinSocket_2x04_P2.54mm_Vertical | J4 |
| 1 | ESP32-S2-MINI-2-N4R2 | ESP32-Mini:ESP32S2MINI2N4R2 | IC1 |
| 1 | GREEN | LED_SMD:LED_0201_0603Metric | D2 |
| 1 | LD2980ABM33TR | LD2980ABM33TR:SOT23-5L_STM | CR1 |
| 1 | LOGO | graphics:theone | G*** |
| 1 | LiPO | Connector_JST:JST_PH_B2B-PH-K_1x02_P2.00mm_Vertical | BT1 |
| 1 | MAX-M10M-00B | MAX-M10:MOD18_MAX-M10M_UBL | U2 |
| 1 | MMC5983MA | MMC5983MA:MMC5983MA_MEM | U5 |
| 1 | MS560702BA03-50 | MS560702BA03:SON8_MS5611_TEC | U6 |
| 1 | PMOS | Reverse Polarity PMOS:DMP3099L-7_DIO | Q1 |
| 1 | PTS636 SM50J SMTR LFS | GSPTS004102:SW_PTS636_CNK | SW1 |
| 1 | Pin_D1.0mm_L10.0mm | Connector_Pin:Pin_D1.0mm_L10.0mm | GPS_ANT |
| 1 | RED | LED_SMD:LED_0201_0603Metric | D1 |
| 1 | W25Q16JVSSIQ | W25Q16JVSSIQ:W25Q16JVSSIQ_WIN | U1 |
More from jespinosa25/Flight-Computer
1- 4 layers31.8 × 38.1 mm

Similar boards
- 6 layers90 × 45 mm

Hw tele stern
shorlee/TeleSTERN
The TeleSTERN Project is an Open Source Rocketry Flight Computer based on the TeleMega by Altus Metrum.
303 parts3GPL-3.0 - 2 layers

- 2 layers85 × 120 mm

Home Assistant Control pad
Pegoku/Home-Assistant-Control-pad
This is a programmable Home Assistant Control Pad. It can control 4 Home assistant devices at a time, and has 4 togglable screens/zones (in total 16 devices).
111 parts1GPL-3.0 - 2 layers63.2 × 27.7 mm

ESPCameleonV2
Alan-GIRAUDON/ESPCameleonV2
ESPCameleonV2 is an ESP32 Camera PCB. It resolve the biggest issues of its first version, ESP32Cameleon. This board allow video capture and streaming through WiFi or USB.
47 partsMIT - 4 layers33 × 90 mm

Active drag system
RocketryVT/active-drag-system
Eigen Library, cmake, and arm-none-eabi-gcc tooling required for successful build.
100 parts6MIT - 4 layers31 × 100 mm

Kp ptr
PTR-projects/PTR_mega_hardware
Welcome to the KPPTR-hardware repository! This repository contains the design files for the hardware components used in the KPPTR project.
208 parts3MIT - 4 layers60 × 60 mm

- 6 layers150 × 100 mm

Questions
How big is the Flight Computer V1 PCB?
It measures 54.6 × 63.5 mm and has 4 copper layers, 1.6 mm thick.
What parts does the Flight Computer V1 use?
60 parts, built around the ESP32-S2-MINI-2-N4R2, MAX-M10M-00B, MMC5983MA and MS560702BA03-50. The full list of its parts is on this page, with links to each part's symbol and footprint where PCBKit's library has them.
Where can I download the Flight Computer V1 KiCad files?
From the jespinosa25/Flight-Computer repository on GitHub, at the commit this page was made from: the board is V1/Flight_Computer_V1.kicad_pcb and its schematic V1/Flight_Computer_V1.kicad_sch. PCBKit opens the board in the browser, with nothing to install.
Can I use the Flight Computer V1 design in my own project?
Its repository states no licence, so its author keeps all rights: ask jespinosa25 before reusing the design.