

Schematics
Esp32-Watch
- Size
- 59.9 × 88.1 mm
- Copper layers
- 4
- Thickness
- 1.6 mm
- Parts
- 50
- Nets
- 84
- Pads
- 276
- Tracks, vias
- 113, 7
- Pours
- 3
- Routed
- Yes
- KiCad
- KiCad 7 (file 20221018)
- Created
- 31 Mar 2023
- Updated
- 14 Sep 2023
Overview
Schematics is an open-source printed circuit board by janc18, from the janc18/ESP32-watchdog repository on GitHub, published under the MIT licence. It is a 4-layer board of 59.9 × 88.1 mm with 50 parts on 84 nets, routed with 113 tracks and 7 vias.
It is built around the ESP32-S3-WROOM-1-N8, CH340G and LIS2MDL, with the AP2112K-3.3, LSM6DS3 and PCF8563T/5 among its other parts. Its parts include 15 capacitors, 9 ICs, 6 resistors, 5 connectors and 2 crystals. It belongs with the wearables boards and the ESP32 boards of this library.
Main components
10ESP32-S3-WROOM-1-N8
SMD,25.5x18mm-40℃~+85℃ -98.2dBm 2.4GHz 20.5dBm 355mA 3V~3.6V 95mA Bluetooth5.0 ESP32-S3 Chip On-board PCB Antenna UART、SPI、I2C、I2S、USB SMD,25.5x18mm WiFi Modules ROHSEspressif SystemsWiFi ModulesCH340G
SOP-16-40℃~+85℃ 2Mbps 3.3V、5V USB 2.0 USB to UART SOP-16 USB Converters ROHSWCH (Nanjing Qinheng Microelectronics)USB ConvertersLIS2MDL
LGA-12(2x2)-40℃~+85℃ 1.71V~3.6V 16bit 200uA I2C、SPI ±5mT ±5mT LGA-12(2x2) 3D Magnetic Sensors ROHSSTMicroelectronics3D Magnetic SensorsAP2112K-3.3
SOT253.3V 600mA CMOS Low Dropout Linear Regulator with EnableDiodes IncorporatedUncategorisedLSM6DS3
LGA-14(2.5x3)-40℃~+85℃ 1.71V~3.6V 8KB Accelerometer Gyroscope SPI、I2C X,Y,Z X,Y,Z ±16g ±2000dps LGA-14(2.5x3) Accelerometers ROHSSTMicroelectronicsAccelerometersPCF8563T/5
SO-8-40℃~+85℃ 0.25uA 1V~5.5V Battery low-voltage detection、Programmable clock output、Alarm function、Countdown timer I2C Yes SO-8 Real Time Clocks ROHSNXP SemiconductorsReal Time ClocksUSBLC6-2P6
SOT-666-6-40℃~+125℃ 150nA 17V 2 3.5pF 5.25V 5A@8/20us 6V ESD IEC 61000-4-2 Unidirectional SOT-666-6 ESD and Surge Protection (TVS/ESD) ROHSSTMicroelectronicsESD And Surge Protection (TVS/ESD)BQ21040DBV
SOT-23-60℃~+125℃ 1 125uA 3.5V~28V 4.2V 800mA Charging IC Support SOT-23-6 Battery Management ROHSTexas InstrumentsBattery ManagementNCP18XH103F03RB
0603-40℃~+125℃ 0.8mm 1.6mm 100mW 10kΩ 1mW/℃ 310uA 3380K 3434K 3455K ±1% ±1% 0603 NTC Thermistors ROHSMurataNTC ThermistorsUMH3N
SOT-363-55℃~+150℃ 0.5uA 100 100mA 150mW 2 NPN (Pre-Biased) 250MHz 300mV 50V 5V 6.11kΩ NPN SOT-363 Digital Transistors ROHSJiangsu Changjing Electronics Technology (CJ)Digital Transistors
README
README.mdESP32-watchdog
This watch will be a multipurpose watch, that will have some kind of Espressif's MCU because it's cheap a come with good features like Bluetooth and Wi-Fi.
I want to have the more compact design, with that said, the screen and battery define the size watch.
Searching on Aliexpress I found the next options
| ID | Technology type | Consumption (mAh) - Voltage (V) | Communication interface | Size | Price | Resolution |
|---|---|---|---|---|---|---|
| 1 | TFT-LCD | 95mAh-5v | UART | 47,5mm diameter x 27,0mm de height | 371 MX | 240px |
| 2 | Electronic paper screen Monochrome | 0.15mAh | - | 1.28in | 574.29 MX 2 units | 128px |
I decided to use the next LCD screen

Maybe in the next iteration I will choose for a smaller screen
Links
- https://es.aliexpress.com/item/1005005295747021.html
- https://es.aliexpress.com/item/1005004555311346.html
Buttons
For applications control it is needed to have some kind of inputs, like in common watches,with the hour configured through buttons. One option is to have capacitive buttons or micro-buttons.
Capacitive touch sensor
Following this document https://ww1.microchip.com/downloads/en/AppNotes/Capacitive-Touch-Sensor-Design-Guide-DS00002934-B.pdf This type of sensor touch it seems the best option, it is called "slide sensor", at "Extend Interpolation" form.
Programming port
The programming port it will be a micro-usb with the CHG340
ESP32-S3's power consumption
| Mode | Power consumption |
|---|---|
| Recommended | 500(mA) |
| deep sleep | 7-8(uA) |
| light sleep | 240(uA) |
| wifi | 355mA |
In the case that I want to use Wi-Fi with another application running for three hours on a day and with powered on screen.
Conceptual design

First PCB design



Parts
50| Qty | Value | Footprint | References |
|---|---|---|---|
| 4 | 100nf | Capacitor_SMD:C_0402_1005Metric | C10, C11, C12, C13 |
| 4 | 1uf | Capacitor_SMD:C_0402_1005Metric | C1, C2, C3, C9 |
| 4 | MountingHole | MountingHole:MountingHole_3.5mm_Pad_Via | H1, H2, H3, H4 |
| 4 | MountingHole | MountingHole:MountingHole_2.2mm_M2_DIN965 | H5, H6, H7, H8 |
| 2 | 0.1u | Capacitor_SMD:C_0402_1005Metric | C6, C7 |
| 2 | 1K | Resistor_SMD:R_0402_1005Metric | R1, R3 |
| 2 | 33p | Capacitor_SMD:C_0402_1005Metric | C4, C5 |
| 2 | 4k7 | Resistor_SMD:R_0402_1005Metric | R4, R5 |
| 2 | Conn_01x06_Female | LCD:slider_sensors_points_smd | J3, J5 |
| 1 | 10k | Resistor_SMD:R_0402_1005Metric | R2 |
| 1 | 10uf | Capacitor_SMD:C_0402_1005Metric | C15 |
| 1 | 1k5 | Resistor_SMD:R_0402_1005Metric | R6 |
| 1 | 1v5 LR44 | LCD:MY-LR44-02 | BT1 |
| 1 | 220nf | Capacitor_SMD:C_0402_1005Metric | C14 |
| 1 | 22p | Capacitor_SMD:C_0402_1005Metric | C8 |
| 1 | 32.768kHz | Crystal:Crystal_SMD_3215-2Pin_3.2x1.5mm | Y2 |
| 1 | 3v7 LIpo | LCD:lipo_battery_800mA | BT2 |
| 1 | AP2112K-3.3 | Package_TO_SOT_SMD:SOT-23-5 | U2 |
| 1 | CH340G | Package_SO:SOIC-16_3.9x9.9mm_P1.27mm | U4 |
| 1 | Conn_01x06_Female | LCD:slide_sensor_6p | J4 |
| 1 | Conn_01x16_Female | Connector_FFC-FPC:TE_1-84953-6_1x16-1MP_P1.0mm_Horizontal | J2 |
| 1 | Crystal_GND2_Small | Crystal:Resonator_SMD_Murata_CSTxExxV-3Pin_3.0x1.1mm | Y1 |
| 1 | ESP32-S3-WROOM-1 | esp:ESP32-S3-WROOM-1 | U1 |
| 1 | LCD | LCD:LCD_IIC_12864 | U6 |
| 1 | LED | LED_SMD:LED_0402_1005Metric_Pad0.77x0.64mm_HandSolder | D1 |
| 1 | LIS2MDL | Package_LGA:LGA-12_2x2mm_P0.5mm | U8 |
| 1 | LSM6DS3 | Package_LGA:LGA-14_3x2.5mm_P0.5mm_LayoutBorder3x4y | U7 |
| 1 | NCP18XH103F03RB | Resistor_SMD:R_0603_1608Metric | TH1 |
| 1 | PCF8563T | Package_SO:SOIC-8_3.9x4.9mm_P1.27mm | U5 |
| 1 | UMH3N | Package_TO_SOT_SMD:SOT-363_SC-70-6 | Q1 |
| 1 | USBLC6-2P6 | Package_TO_SOT_SMD:SOT-666 | U9 |
| 1 | USB_B_Micro | Connector_USB:USB_Micro-B_Amphenol_10118194_Horizontal | J1 |
| 1 | bq21040 | Package_TO_SOT_SMD:SOT-23-6_Handsoldering | U3 |
Similar boards
- 2 layers92.1 × 78.1 mm

- 4 layers106 × 80 mm

Mainboard
PyroVision-ThermalCam/Mainboard
Mainboard for the PyroVision thermal camera.
152 parts11GPL-3.0 - 2 layers31.5 × 75 mm

- 4 layers138.1 × 104.6 mm

V7-kaleido
vroland/epdiy-hardware
Hardware design files for EPDiy: https://github.com/vroland/epdiy.
140 parts75CC-BY-SA-4.0 - 2 layers91.5 × 100 mm

Trailmap
katetriestocode/trailmap
this is the working version! (disclaimer: no antenna as it has not delivered yet, so manual gps coords insertion for now!)
57 parts2 - 4 layers35 × 45 mm

- 4 layers32 × 45 mm

- 2 layers25.4 × 55.9 mm

Questions
How big is the Schematics PCB?
It measures 59.9 × 88.1 mm and has 4 copper layers, 1.6 mm thick.
What parts does the Schematics use?
50 parts, built around the ESP32-S3-WROOM-1-N8, CH340G, LIS2MDL and AP2112K-3.3. The full list of its parts is on this page, with links to each part's symbol and footprint where PCBKit's library has them.
Where can I download the Schematics KiCad files?
From the janc18/ESP32-watchdog repository on GitHub, at the commit this page was made from: the board is schematics/Main_board/Main_board/Main_board.kicad_pcb and its schematic schematics/Main_board/Main_board/Main_board.kicad_sch. PCBKit opens the board in the browser, with nothing to install.
Can I use the Schematics design in my own project?
Its repository publishes it under the MIT licence: you may reuse it on that licence's terms (keep the author's notice, and for a copyleft licence share your changes alike).