Skip to the content
123456

BQ21040DBV

Texas InstrumentsExtended

0℃~+125℃ 1 125uA 3.5V~28V 4.2V 800mA Charging IC Support SOT-23-6 Battery Management ROHS

Part id
ti/BQ21040DBV
Category
Battery Management
Package
SOT-23-6
Pins
6
In stock
2,551 at JLCPCB (C202311)
Used on
35 open-source boards

Overview

The BQ21040DBV is a battery Management made by Texas Instruments in a SOT-23-6 package with 6 pins. 0℃~+125℃ 1 125uA 3.5V~28V 4.2V 800mA Charging IC Support SOT-23-6 Battery Management ROHS.

PCBKit's library has its KiCad symbol (Battery_Management:BQ21040DBV, from KiCad's library) and its footprint (Package_TO_SOT_SMD:SOT-23-6, from KiCad's library), ready for a KiCad board. 2,551 are in stock at JLCPCB (part C202311). 35 open-source boards in 33 repositories on GitHub use it.

Symbol

1TS2OUT3CHG4ISET5GND6VIN
Battery_Management:BQ21040DBVFrom KiCad's library

Footprint

123456
Package_TO_SOT_SMD:SOT-23-6From KiCad's library

From the datasheet

16
Supply, least
3.5 V · VIN, recommended IN voltage range, min · p. 4
Supply, most
28 V · VIN, recommended IN voltage range, max · p. 4
Supply, least
4.45 V · VIN, operating range restricted by VDPM and VOVP, min · p. 4
Supply, most
6.45 V · VIN, operating range restricted by VDPM and VOVP, max · p. 4
Supply, absolute maximum
30 V · IN with respect to VSS, absolute max · p. 3
Junction, hottest
150 °C · Junction temperature, absolute max · p. 3
Takes working
1 mA · IN active supply current, VIN = 6 V, max · p. 5
Takes asleep
125 µA · IN standby current, TS = Low, VIN ≤ 6 V, max · p. 5
Gives
800 mA · OUT recommended continuous current, max · p. 4
Current limit
1.05 A · OUT current clamp, VIN = 5 V, VOUT = 3.6 V, min · p. 5
A pin gives at most
15 mA · CHG output sink current, absolute max · p. 3
Output
4.2 V · Battery regulation voltage, IL = 25 mA, VIN = 5.5 V, typical · p. 5
Dropout
325 mV · VIN – VOUT at IOUT = 0.5 A, VOUT = 4.15 V, typical · p. 5
Junction to air (DBV (SOT-23))
130.8 K/W · Junction-to-ambient thermal resistance · p. 4
Junction to case (DBV (SOT-23))
75.2 K/W · Junction-to-case top thermal resistance · p. 4
Junction to board (DBV (SOT-23))
45.5 K/W · Junction-to-board thermal resistance · p. 4

What it is and has

9
Battery chemistry
Single-cell Li-Ion and Li-Pol · p. 1
Charge voltage accuracy
1% · p. 1
Charge current accuracy
10% · p. 1
Charge voltage
4.2 V · p. 1
Protection
Input Voltage Dynamic Power Management · p. 1
Safety timer
Fixed 10 hours · p. 1
Status indication
Charging/Done · p. 1
Package
SOT-23, 6 pins, 3.00 mm × 1.75 mm body · p. 1
Battery leakage current
1 µA · p. 1

Around it

9
res 10.8kΩ (50mA) to 675Ω (800mA)
between ISET and VSS; External fast-charge programming resistor. · p. 3
res 10 kΩ
between TS and VSS; Use when NTC sensing is not needed. · p. 3
res 237 kΩ
between TS and GND; Prevents entering TTDM when the battery thermistor is removed. · p. 3
cap 1μF to 10μF
between VIN and VSS; Input bypass capacitance. · p. 3
diode 6.2-V
between CHG and VSS; Zener voltage clamp if the CHG pull-up source can exceed 7 V. · p. 13
res 1.0 kΩ
between ISET and Vss; Fast charge current programming resistor for the 540 mA application example. · p. 18
other 10k NTC thermistor (103AT)
between TS and VSS; Battery temperature sensing thermistor in the battery pack. · p. 18
res 10k
between TS and Vss; Fixed resistor used to disable temperature sensing. · p. 18
res 1.5kΩ
between OUT and CHG; Connect in series with an LED for charge status indication. · p. 18

Specifications

76
ParameterConditionsAs printedPage
Input voltageIN (with respect to VSS)min -0.3 · max 30 V3
Input voltageOUT (with respect to VSS)min -0.3 · max 7 V3
Input voltagePRE-TERM, ISET, ISET2, TS, /CHG (with respect to VSS)min -0.3 · max 7 V3
Input currentINmax 1.25 A3
Output current (continuous)OUTmax 1.25 A3
Output sink currentCHGmax 15 mA3
Junction temperature TJmin -40 · max 150 °C3
Storage temperature Tstgmin -65 · max 150 °C3
Electrostatic discharge V(ESD)Human-body model (HBM), per ANSI/ESDA/JEDEC JS-001min -2000 · max 2000 V4
Electrostatic discharge V(ESD)Charged-device model (CDM), per JEDEC specification JESD22-C101min -500 · max 500 V4
IN voltage range VINmin 3.5 · max 28 V4
IN operating voltage range, restricted by VDPM and VOVP VINmin 4.45 · max 6.45 V4
Input current, IN terminal IINmax 0.8 A4
Current, OUT terminal IOUTmax 0.8 A4
Junction temperature TJmin 0 · max 125 °C4
Fast-charge current programming resistor RISETmin 0.675 · max 10.8 kΩ4
10k NTC thermistor range without entering TTDM RTSmin 1.66 · max 258 kΩ4
Junction-to-ambient thermal resistance RθJAbq21040, DBV (SOT-23), 6 PINStyp 130.8 °C/W4
Junction-to-case (top) thermal resistance RθJC(top)bq21040, DBV (SOT-23), 6 PINStyp 75.2 °C/W4
Junction-to-board thermal resistance RθJBbq21040, DBV (SOT-23), 6 PINStyp 45.5 °C/W4
Junction-to-top characterization parameter ψJTbq21040, DBV (SOT-23), 6 PINStyp 31.8 °C/W4
Junction-to-board characterization parameter ψJBbq21040, DBV (SOT-23), 6 PINStyp 45.5 °C/W4
Undervoltage lockout exit UVLOVIN: 0 V to 4 Vmin 3.15 · typ 3.3 · max 3.45 V4
Hysteresis on VUVLO_RISE falling VHYS-UVLOVIN: 0 V to 4 V, VUVLO_FALL = VUVLO_RISE – VHYS-UVLOmin 175 · typ 227 · max 280 mV4
Input power good detection threshold is VOUT+VIN-DT VIN-DTInput power good if VIN > VOUT + VIN-DT; VOUT = 3.6 V, VIN: 3.5 V to 4 Vmin 30 · typ 80 · max 145 mV4
Hysteresis on VIN-DT falling VHYS-INDTVOUT = 3.6 V, VIN: 4 V to 3.5 Vtyp 31 mV4
Input overvoltage protection threshold VOVPVIN: 5 V to 12 Vmin 6.5 · typ 6.65 · max 6.8 V4
Hysteresis on OVP VHYS-OVPVIN: 11 V to 5 Vtyp 95 mV4
Adaptor low input voltage protection. Restricts lout at VIN-DPM VIN-DPMFeature active in adaptor mode; Limit Input Current to 50 mA; VOUT = 3.5 V; RISET = 825min 4.24 · typ 4.3 · max 4.46 V4
Highest resistance considered a fault (short). Monitored for IOUT>90mA RISET_SHORTRISET: 250 Ω to 540 Ω, Iout latches off. Cycle power to resetmax 500 Ω4
Maximum OUT current limit regulation (clamp) IOUT_CLVIN = 5 V, VOUT = 3.6 V, RISET: 250 Ω to 540 Ω, Iout latches off after tDGL-SHORTmin 1.05 · max 1.4 A5
OUT terminal short-circuit detection threshold/precharge threshold VOUT(SC)Vout:3V to 0.5V, no deglitchmin 0.75 · typ 0.8 · max 0.85 V5
OUT terminal short hysteresis VOUT(SC-HYS)Recovery ≥ VOUT(SC) + VOUT(SC-HYS); Rising, no deglitchtyp 77 mV5
Source current to OUT terminal during short-circuit detection IOUT(SC)min 10 · typ 15 · max 20 mA5
Battery current into OUT terminal IOUT(PDWN)VIN = 0Vmax 1 uA5
OUT pin current, charging terminated IOUT(DONE)VIN = 6 V, VBAT > VBAT(REG), net current is into OUT pinmax 6 uA5
Standby current into IN pin IIN(STDBY)TS = Low, VIN ≤ 6 Vmax 125 uA5
Active supply current, IN pin ICCTS = Low, VIN = 6 V, no load on OUT pin, VBAT > VBAT(REG)max 1000 uA5
Battery regulation voltage VOUT(REG)VREG = 4.2 V, IL = 25 mA, VIN = 5.5 Vmin 4.16 · typ 4.2 · max 4.23 V5
Programmed output fast charge current range IOUT(RANGE)VOUT(REG) > VOUT > VLOWV; VIN = 5 V, RISET = 0.675 to 52 kΩmin 10 · max 800 mA5
Drop-Out, VIN – VOUT VDO(IN-OUT)Adjust VIN down until IOUT = 0.5 A, VOUT = 4.15 V, RISET = 1.08kΩtyp 325 · max 550 mV5
Fast charge current factor KISETKISET (60mA < I <1000mA)min 490 · typ 540 · max 590 AΩ5
Fast charge current factor KISETKISET (25mA < I < 60mA)min 470 · typ 527 · max 605 AΩ5
Fast charge current factor KISETKISET (10mA < I < 25mA)min 340 · typ 520 · max 685 AΩ5
Pre-charge to fast-charge transition threshold VLOWVmin 2.4 · typ 2.5 · max 2.6 V5
Default pre-charge current Pre-chargeVBAT < VLOWV, ICHG = 50 mAmin 18 · typ 20 · max 22 %ISET5
Termination Threshold Current, default setting %TERMVOUT > VRCH; RISET = 1 kΩmin 9 · typ 10 · max 11 %IOUT-CC5
Sink current during VREG-BD IBD-SINKVIN = 5 V, VTS = 0.5 V, battery absentmin 7 · max 10 mA5
NTC bias current INTC 50uAmin 48 · typ 50 · max 53 uA5
10K NTC bias current when charging is disabled INTC-DIS-10KVTS = 0 Vmin 27 · typ 30 · max 34 uA5
INTC is reduced prior to entering TTDM to keep cold thermistor from entering TTDM INTC-FLDBK -10KVTS = 1.525 Vmin 4 · typ 5 · max 6.5 uA5
Termination and timer disable mode-Threshold-Enter VTTDM(TS)VTS: 0.5 V to 1.7 V; timer held in resetmin 1550 · typ 1600 · max 1650 mV6
Hysteresis exiting TTDM IHYS-TTDM(TS)VTS: 1.7 V to 0.5 V; timer enabledtyp 100 mV6
TS maximum voltage clamp VCLAMP(TS)VTS = Open (float)min 1800 · typ 1950 · max 2000 mV6
TS voltage where INTC is reduce to keep thermistor from entering TTDM VTS_I-FLDBKINTC adjustment (90 to 10%; 45 to 6.6 us) takes place near this spec threshold. VTS: 1.425 V to 1.525 Vtyp 1475 mV6
Optional capacitance – ESD CTStyp 0.22 uF6
Low temperature CHG pending VTS-0CNormal temperature charging to pending; VTS: 1 V to 1.5 Vmin 1220 · typ 1250 · max 1280 mV6
Hysteresis at 0°C VHYS-0CCharge pending to normal temperature charging; VTS: 1.5 V to 1 Vtyp 100 mV6
High temperature CHG disable VTS-45CNormal temperature charging to pending; VTS: 0.5 V to 0.2 Vmin 260 · typ 275 · max 290 mV6
Hysteresis at 45°C VHYS-45CCharge pending to normal temperature charging; VTS: 0.2 V to 0.5 Vtyp 20 mV6
Charge enable threshold (10k NTC) VTS-EN-10KVTS: 0 V to 0.175 Vmin 80 · typ 88 · max 96 mV6
HYS below VTS-EN-10k to disable (10k NTC) VTS-DIS_HYS-10KVTS: 0.125 V to 0 Vtyp 12 mV6
Temperature regulation limit TJ(REG)typ 125 °C6
Thermal shutdown temperature TJ(OFF)typ 155 °C6
Thermal shutdown hysteresis TJ(OFF-HYS)typ 20 °C6
Output Low Voltage-CHG FET on - first charge after power-up VOLISINK = 5 mAmax 0.4 V6
Leakage current into IC ILEAKV CHG = 5 Vmax 1 uA6
Input over-voltage blanking time tDGL(OVP_SET)VIN: 5 V to 12 Vtyp 113 us6
Deglitch time exiting OVP tDGL(OVP_REC)Time measured from VIN: 12V to 5Vtyp 30 us6
Deglitch time transition from ISET short to IOUT disable tDGL_SHORTClear fault by disconnecting IN or cycling (high / low) TStyp 1 ms6
Deglitch time on pre-charge to fast-charge transition tDGL1(LOWV)Set internallytyp 70 us6
Deglitch time on fast-charge to pre-charge transition tDGL2(LOWV)Set internallytyp 32 ms6
Deglitch time, termination detected tDGL(TERM)typ 29 ms6
Deglitch time, recharge threshold detected tDGL1(RCHG)VIN = 5 V, VTS = 0.5 V, VOUT: 4.25 V to 3.5 V in 1 us; tDGL(RCHG) is time to ISET ramptyp 29 ms6
Regulation time at VREG or VREG-BD tDGL(HI/LOW REG)typ 25 ms6
Deglitch for TS thresholds: 0/45C. tDGL(TS)Battery chargingtyp 30 ms6

Pins, by the datasheet

6
1 TS
Temperature sense for a 10k at 25°C battery NTC; floating or high selects TTDM and disables TS monitoring, timers and termination; low disables the IC. Use 10 kΩ to VSS without NTC sensing; 237 kΩ to ground prevents TTDM when the thermistor is removed. · p. 3
2 OUT
Battery connection; a system load may be connected. Expected bypass capacitance is 1uF to 10uF. · p. 3
3 CHG
Low indicates charging; open drain off indicates no charging or charge complete. · p. 3
4 ISET
Programs fast-charge current using an external resistor to VSS, from 10.8kΩ for 50mA to 675Ω for 800mA. · p. 3
5 GND
Ground terminal. · p. 3
6 VIN
Input power from an AC adapter or USB port; connect 1uF to 10uF bypass capacitance from IN to VSS. · p. 3

Ordering codes, by the datasheet

4
BQ21040DBVR
SOT-23 (DBV) · 6 pins; 3000 units, LARGE T&R · p. 25
BQ21040DBVR.B
SOT-23 (DBV) · 6 pins; 3000 units, LARGE T&R · p. 25
BQ21040DBVT
SOT-23 (DBV) · 6 pins; 250 units, SMALL T&R · p. 25
BQ21040DBVT.B
SOT-23 (DBV) · 6 pins; 250 units, SMALL T&R · p. 25

Open-source boards using it

35See all 35
  • 4 layers50 × 50 mmFpgaboy, the printed circuit board in 3D

    Fpgaboy

    Wren6991/RISCBoy

    Portable games console, designed from scratch: CPU, graphics, PCB, and the kitchen sink

    93 parts513
  • 2 layers285 × 94.6 mmKeyboard, the printed circuit board in 3D

    Keyboard

    andrewcchen/blu60

    259 parts20
  • 2 layers65.4 × 41.9 mmCompact design neo, the printed circuit board in 3D

    Compact design neo

    lpechacek/u-blox-gnss-receiver

    Document about design of a GNSS receiver

    41 parts14
  • 4 layers106 × 80 mmMainboard, the printed circuit board in 3D

    Mainboard

    PyroVision-ThermalCam/Mainboard

    Mainboard for the PyroVision thermal camera.

    152 parts11GPL-3.0
  • 2 layers92.1 × 78.1 mmPaperd ink rev3, the printed circuit board in 3D

    Paperd ink rev3

    paperdink/paperd.ink_hw

    Hardware files for paperd.ink

    92 parts9CC-BY-SA-4.0
  • 2 layers70 × 40 mmScale ltc6915, the printed circuit board in 3D

    Scale ltc6915

    IoTReady/low-power-nrf52-weighing-scale

    https://iotready.co/low-power-nrf52-weighing-scale/

    76 parts7
  • 2 layers56 × 44 mmCphp82001-pcb, the printed circuit board in 3D

    Cphp82001-pcb

    calcpsu/cphp82001

    CalcPack replacement for HP 82001, suits HP35/45/55/65/67 calculators

    30 parts4
  • 4 layers76.9 × 67.3 mmTerra HW, the printed circuit board in 3D

    Terra HW

    jamesmendel/terra-nova

    Terra 2.0 Firmware and Hardware

    95 parts2GPL-3.0

Parts like it

8

Questions

Is there a KiCad symbol and footprint for the BQ21040DBV?

Yes. The symbol is Battery_Management:BQ21040DBV and the footprint Package_TO_SOT_SMD:SOT-23-6, both drawn on this page. PCBKit places them on a board for you when you design with it.

What package is the BQ21040DBV?

SOT-23-6, with 6 pins. Its footprint is drawn on this page.

Where is the BQ21040DBV datasheet?

Texas Instruments publishes it: the Datasheet link on this page opens it.

Where can I order the BQ21040DBV?

JLCPCB lists it as part C202311, with 2,551 in stock; the sellers' links on this page open their listings.

What can replace the BQ21040DBV?

Parts like it in the library: the TP4057 by UMW, the DW01A by PUOLOP, the DW01-A/J by Shenzhen Fuman Elec and the TP4057-42-SOT26-R by TOPPOWER. Check their datasheets: a part that fits the footprint may still differ in its ratings.

Which open-source boards use the BQ21040DBV?

35 boards in 33 repositories on GitHub; the most starred are listed on this page, with their KiCad files.