

Paperd ink rev3
Hardware files for paperd.ink
- Size
- 92.1 × 78.1 mm
- Copper layers
- 2
- Thickness
- 1.6 mm
- Parts
- 92
- Nets
- 76
- Pads
- 369
- Tracks, vias
- 764, 268
- Pours
- 8
- Routed
- Yes
- KiCad
- KiCad 6 (file 20211014)
- Created
- 13 Apr 2022
- Updated
- 14 Aug 2022
Overview
Paperd ink rev3 is an open-source printed circuit board by paperdink, from the paperdink/paperd.ink_hw repository on GitHub, published under the CC-BY-SA-4.0 licence. It is a 2-layer board of 92.1 × 78.1 mm with 92 parts on 76 nets, routed with 764 tracks and 268 vias.
It is built around the ESP32-WROOM-32D, CP2104-F03-GMR and PCF8574APWR, with the HYC77-TF09-200, BQ21040DBV and USBLC6-2SC6 among its other parts. Its parts include 29 resistors, 24 capacitors, 7 transistors, 6 ICs and 5 diodes. It belongs with the ESP32 boards of this library.
Main components
12ESP32-WROOM-32D
-- WiFi Modules ROHSEspressif SystemsWiFi ModulesCP2104-F03-GMR
QFN-24-EP(4x4)-40℃~+85℃ 1.8V、3V~3.6V 100uA 17mA 2Mbps USB 2.0 USB to UART QFN-24-EP(4x4) USB Converters ROHSSilicon LabsUSB ConvertersPCF8574APWR
ETSSOP-20-40℃~+85℃ 100kHz 10uA 2.5V~6V 25mA 310uA 8 Cascading and address extension、Built-in LED driver I2C Interrupt Output Push-Pull ETSSOP-20 I/O Expanders ROHSTexas InstrumentsI/O ExpandersHYC77-TF09-200
SMD-25℃~+85℃ 2mm Connector and Ejector MicroSD Card (TF Card) Push-Push Yes SMD SD Card / Memory Card Connector ROHSHOAUCSD Card / Memory Card ConnectorBQ21040DBV
SOT-23-60℃~+125℃ 1 125uA 3.5V~28V 4.2V 800mA Charging IC Support SOT-23-6 Battery Management ROHSTexas InstrumentsBattery ManagementUSBLC6-2SC6
SOT-23-60.35pF、0.8pF 100nA 150W@8/20us 15V 2 5V 6A@8/20us 6V ESD SOT-23-6 ESD and Surge Protection (TVS/ESD) ROHSUMWESD And Surge Protection (TVS/ESD)XC6220B331MR-G
SOT-25-40℃~+85℃ 1 1A 3.3V 50dB@(1kHz) 655mV@(1A) 6V 8uA Fixed Over Current Protection、Short Circuit Protection、Thermal shutdown、Enable control、Output discharge Positive SOT-25 Voltage Regulators - Linear, Low Drop Out (LDO) Regulators ROHSTorex SemiconductorVoltage Regulators - Linear, Low Drop Out (LDO) RegulatorsRMS04JT103
0402-55℃~+155℃ 10kΩ 50V 62.5mW Thick Film Resistor ±200ppm/℃ ±5% 0402 Chip Resistor - Surface Mount ROHSTA-I TechChip Resistor - Surface MountWR04X122JTL
0402-55℃~+155℃ 1.2kΩ 50V 62.5mW Thick Film Resistor ±100ppm/℃ ±5% 0402 Chip Resistor - Surface Mount ROHSWalsin TechnologyChip Resistor - Surface MountWR04X4703FTL
0402-55℃~+155℃ 470kΩ 50V 62.5mW Thick Film Resistor ±1% ±100ppm/℃ 0402 Chip Resistor - Surface Mount ROHSWalsin TechnologyChip Resistor - Surface MountTS36CA-0.7
SMD,7.6x3.5mm-20℃~+70℃ 12V 2.5N 3.5mm 3.5mm 30,000 cycles 50mA 7.6mm Black No Rectangular Button SMD(SMT) Tab SPST Surface Mount, Right Angle Without Bracket SMD,7.6x3.5mm Tactile Switches ROHSSHOU HANTactile SwitchesDMP2035U-7(ES)
SOT-23SOT-23 MOSFETs ROHSElecSuperMOSFETs
README
README.mdpaperd.ink PCB files
Parts
92| Qty | Value | Footprint | References |
|---|---|---|---|
| 12 | 10k | Resistor_SMD:R_0402_1005Metric | R4, R5, R13, R14, R15, R16, R17, R18, R19, R20, R25, R26 |
| 12 | 1uF/50V | Capacitor_SMD:C_0603_1608Metric | C1, C2, C3, C5, C6, C10, C11, C12, C13, C14, C15, C16 |
| 5 | 1.2k | Resistor_SMD:R_0402_1005Metric | R2, R8, R12, R22, R27 |
| 5 | 1uF/25V | Capacitor_SMD:C_0402_1005Metric | C4, C8, C17, C18, C20 |
| 5 | 470k | Resistor_SMD:R_0402_1005Metric | R1, R3, R9, R24, R29 |
| 4 | BTN | 021_labs:TS36CA-0.7 | SW2, SW3, SW4, SW5 |
| 4 | DMP2035 | Package_TO_SOT_SMD:SOT-23 | Q1, Q3, Q4, Q5 |
| 4 | LMBR130 | Diode_SMD:D_SOD-123 | D1, D2, D3, D4 |
| 3 | 1M | Resistor_SMD:R_0402_1005Metric | R7, R11, R21 |
| 3 | MountingHole | 021_labs:JLCPCB_Tooling_Hole | H1, H2, H3 |
| 2 | 0.1uF/50V | Capacitor_SMD:C_0402_1005Metric | C21, C24 |
| 2 | 12pF/50V | Capacitor_SMD:C_0402_1005Metric | C22, C23 |
| 2 | 4.7uF/50V | Capacitor_SMD:C_0805_2012Metric | C7, C9 |
| 2 | T2N7002BK | Package_TO_SOT_SMD:SOT-23 | Q2, Q8 |
| 1 | 0.47 | Resistor_SMD:R_0603_1608Metric | R6 |
| 1 | 1.6M | Resistor_SMD:R_0402_1005Metric | R10 |
| 1 | 10uF/6.3V | Capacitor_SMD:C_0402_1005Metric | C19 |
| 1 | 120 | Resistor_SMD:R_0402_1005Metric | R28 |
| 1 | 1A | Fuse:Fuse_0805_2012Metric | F1 |
| 1 | 32.768KHz | 021_labs:Q13FC1350000400 | Y1 |
| 1 | 470 | Resistor_SMD:R_0402_1005Metric | R23 |
| 1 | 68uH/1A | Inductor_SMD:L_1210_3225Metric | L1 |
| 1 | BQ21040 | Package_TO_SOT_SMD:SOT-23-6 | U2 |
| 1 | CP2104 | Package_DFN_QFN:QFN-24-1EP_4x4mm_P0.5mm_EP2.6x2.6mm | U4 |
| 1 | E-paper_24_pins | 021_labs:24 pin FPC connector | DS1 |
| 1 | EXT_CONN | Connector_PinHeader_2.54mm:PinHeader_2x13_P2.54mm_Vertical_SMD | J4 |
| 1 | GDEW042T2 | 021_labs:GDEW042T2 | DISP1 |
| 1 | IO_EXP_JMP | Jumper:SolderJumper-2_P1.3mm_Bridged_RoundedPad1.0x1.5mm | JP1 |
| 1 | LED_Small | 021_labs:TJ-S1706SW6TGLC2R-A5 | D5 |
| 1 | LOGO | 021_labs:papered_ink_logo_horizontal | G*** |
| 1 | LiPo | Connector_JST:JST_PH_B2B-PH-SM4-TB_1x02-1MP_P2.00mm_Vertical | BATT1 |
| 1 | OLIMEX_Cases_ESP-WROOM-32 | RF_Module:ESP32-WROOM-32 | U6 |
| 1 | PCF8574APWR | Package_SO:TSSOP-20_4.4x6.5mm_P0.65mm | U5 |
| 1 | Piezo_Buzzer | 021_labs:KLJ-1230 | BZ1 |
| 1 | RESET | 021_labs:K2-1822SA-A3DW-06 | SW1 |
| 1 | UMH3N | Package_TO_SOT_SMD:SOT-363_SC-70-6 | Q6 |
| 1 | USBLC6-2SC6 | Package_TO_SOT_SMD:SOT-23-6 | U3 |
| 1 | USB_B_Micro | 021_labs:C77238 | J1 |
| 1 | XC6220B331MR-G | Package_TO_SOT_SMD:SOT-23-5 | U1 |
| 1 | micro_sd_card | 021_labs:HYC77-TF09-200 | MICRO_SD1 |
The 91 most common of 92 parts.
More from paperdink/paperd.ink_hw
2- 2 layers92.1 × 78.1 mm

- 4 layers92.1 × 8 mm

Similar boards
- 4 layers40 × 40 mm

Ble actuator board
seanconway/ble-actuator-board
BLE smart-lock board: nRF52840 + nPM1300 + DRV8213, KiCad 10
64 parts - 4 layers50 × 50 mm

- 4 layers94.1 × 152 mm

Development board panel
portapack-mayhem/mayhem-mdk
PortaPack - Module Develoment Kit
298 parts88GPL-3.0 - 4 layers41.5 × 41.5 mm

ZenFly F71
LongDo1902/STM32_Drone
Developing quadcopter from scratch including stm32 programing and self-built flight controller PCB.
180 parts - 2 layers125 × 85 mm

- 2 layers40 × 40 mm

PCB PCB wristwatch v1.1 2024-03-06
The-Wrench/Smart-watch-PCB-esp32s3
a smart watch making use of HDSP-2000 alphanumeric displays and an esp32s3 with an RTC/c
74 parts3 - 4 layers76 × 88 mm

- 2 layers89 × 44 mm

Questions
How big is the Paperd ink rev3 PCB?
It measures 92.1 × 78.1 mm and has 2 copper layers, 1.6 mm thick.
What parts does the Paperd ink rev3 use?
92 parts, built around the ESP32-WROOM-32D, CP2104-F03-GMR, PCF8574APWR and HYC77-TF09-200. The full list of its parts is on this page, with links to each part's symbol and footprint where PCBKit's library has them.
Where can I download the Paperd ink rev3 KiCad files?
From the paperdink/paperd.ink_hw repository on GitHub, at the commit this page was made from: the board is rev3/paperd_ink_rev3.kicad_pcb and its schematic rev1/paperd.ink_V1.kicad_sch. PCBKit opens the board in the browser, with nothing to install.
Can I use the Paperd ink rev3 design in my own project?
Its repository publishes it under the CC-BY-SA-4.0 licence: you may reuse it on that licence's terms (keep the author's notice, and for a copyleft licence share your changes alike).