2 layers37.5 × 33 mm
W210 CAN
Blackbird128/W210_canbus
Hardware interface to communicate with the CAN-B bus on a Mercedes W210
17 parts1
2 layers49 × 27.5 mm
Hw11c
igkov/bcomp11hw2BCOMP11 hardware project
- Size
- 49 × 27.5 mm
- Copper layers
- 2
- Thickness
- 1.6 mm
- Parts
- 89
- Nets
- 69
- Pads
- 258
- Tracks, vias
- 1,117, 89
- Pours
- 2
- Routed
- Yes
- KiCad
- KiCad 4
- Created
- 19 Dec 2017
- Updated
- 19 Jul 2018
Overview
Hw11c is an open-source printed circuit board by igkov, from the igkov/bcomp11hw repository on GitHub, published under the MIT licence. It is a 2-layer board of 49 × 27.5 mm with 89 parts on 69 nets, routed with 1,117 tracks and 89 vias.
It is built around the LPC11C14FBD48/301, MCP2551-I/P and TJA1055T/C, with the BC817, 24C16 and LP2985-33DBV among its other parts. Its parts include 28 resistors, 18 capacitors, 18 crystals, 7 diodes and 2 switches. It belongs with the NXP (LPC, Kinetis, i.MX RT) boards of this library.
Main components
6
LPC11C14FBD48/301
LQFP-48(7x7)-40℃~+85℃ 1.8V~3.6V 32 Bit 32KB 40 50MHz 8KB ARM Cortex-M0 Built-in FLASH LQFP-48(7x7) Microcontrollers (MCU/MPU/SOC) ROHSNXP SemiconductorsMicrocontrollers (MCU/MPU/SOC)
MCP2551-I/P
PDIP-8-40℃~+85℃ 1Mbps 365uA 4.5V~5.5V 75mA CAN Transceiver PDIP-8 CAN Transceivers ROHSMicrochip TechnologyCAN Transceivers
TJA1055T/C
SOIC-14-40℃~+125℃ 125Kbps 21mA 4.75V~5.25V 40uA CAN Transceiver SOIC-14 CAN Transceivers ROHSNXP SemiconductorsCAN Transceivers
BC817
SOT-231 NPN 100nA 150MHz 300mW 40 45V 500mA 5V 700mV NPN SOT-23 Bipolar (BJT) ROHSShikuesBipolar (BJT)
24C16
SOP-8SOP-8 EEPROM ROHSGAOGE MICROCHIPEEPROM
LP2985-33DBV
SOT-23-5-40℃~+125℃@(Tj) 1 150mA 16V 3.3V 30uVrms 45dB@(1kHz) 575mV@(150mA) 850uA Fixed Over Current Protection、Short Circuit Protection、Thermal shutdown、Enable control、Noise bypass terminal Positive SOT-23-5 Voltage Regulators - Linear, Low Drop Out (LDO) Regulators ROHSTexas InstrumentsVoltage Regulators - Linear, Low Drop Out (LDO) Regulators
README
README.mdbcomp11hw
Hardware made in KiCad software. This project of BCOMP11 hardware. Description on http://igorkov.org/bcomp11 and http://igorkov.org/bcomp11v2 pages.
Actual Gerber files here:
- Version 2.0 - http://igorkov.org/zip/bcomp11v2-gerber.zip
- Version 2.3 - http://igorkov.org/zip/bcomp11v2-gerber23.zip
Other information:
Scheme:
Board:
Parts
89| Qty | Value | Footprint | References |
|---|---|---|---|
| 11 | 0.1 | libs:C_0603 | C3, C6, C8, C9, C12, C13, C14, C15, C16, C17, C18 |
| 10 | 10k | libs:R_0603 | R1, R5, R6, R8, R16, R17, R18, R19, R27, R28 |
| 6 | 4.7k | libs:R_0603 | R3, R4, R22, R23, R24, R26 |
| 4 | 22p | libs:C_0603 | C1, C2, C10, C11 |
| 4 | BC817 | libs:SOT-23 | QT1, QT2, QT3, QT4 |
| 3 | 0 | libs:R_0603 | R10, R11, R14 |
| 2 | 10u | libs:C_1206 | C5, C7 |
| 2 | 5.6k | libs:R_0603 | R20, R21 |
| 2 | 680 | libs:R_0603 | R12, R13 |
| 2 | LED | libs:LED-0603 | VD1, VD2 |
| 1 | 120 | libs:R_0603 | R9 |
| 1 | 1k | libs:R_0603 | R7 |
| 1 | 1u | libs:C_1206 | C4 |
| 1 | 24C16 | libs:SOIC-8_3.9x4.9mm_Pitch1.27mm | D5 |
| 1 | 33k | libs:R_0603 | R25 |
| 1 | 78M05 | libs:D-Pak_TO252AA | D7 |
| 1 | ADC3 | libs:PAD | X12 |
| 1 | ADC6 | libs:PAD | X18 |
| 1 | BUTT1 | libs:SW_SPST_FSMSM | SW1 |
| 1 | BUTT2 | libs:SW_SPST_FSMSM | SW2 |
| 1 | DB9 | libs:DB9M_CI | XT3 |
| 1 | EXT | libs:Pin_Header_Straight_1x06 | XT5 |
| 1 | INF | libs:R_0603 | R2 |
| 1 | ISP | libs:Pin_Header_Angled_1x06 | XT1 |
| 1 | KX-7_12MHZ | libs:KX-7 | Q1 |
| 1 | LM2931-5.0 | libs:TO-92_Horizontal1_Inline_Narrow_Oval | D2 |
| 1 | LP2985-3.3 | libs:SOT-23-5 | D4 |
| 1 | LPC11C14FBD48 | libs:LQFP-48_7x7mm_Pitch0.5mm | D1 |
| 1 | MAT0 | libs:PAD | X15 |
| 1 | MCP2551 | libs:SOIC-8_3.9x4.9mm_Pitch1.27mm | D3 |
| 1 | MISO1 | libs:PAD | X6 |
| 1 | MOSI1 | libs:PAD | X7 |
| 1 | OLED | libs:OLED_I2C | XT2 |
| 1 | PIO0.6 | libs:PAD | X16 |
| 1 | PIO0.7 | libs:PAD | X17 |
| 1 | PIO0.8 | libs:PAD | X13 |
| 1 | PIO0.9 | libs:PAD | X14 |
| 1 | PIO1.4 | libs:PAD | X11 |
| 1 | PIO2.6 | libs:PAD | X8 |
| 1 | PIO2.7 | libs:PAD | X9 |
| 1 | PIO2.8 | libs:PAD | X10 |
| 1 | SCK1 | libs:PAD | X5 |
| 1 | SPEAKER | libs:HC0901F | SP1 |
| 1 | SSEL1 | libs:PAD | X4 |
| 1 | SWCLK | libs:PAD | X2 |
| 1 | SWDIO | libs:PAD | X3 |
| 1 | TJA1055 | libs:SOIC-14_3.9x8.7mm_Pitch1.27mm | D6 |
| 1 | inf | libs:R_0603 | R15 |
| 1 | ~RESET | libs:PAD | X1 |
The 85 most common of 89 parts.
Similar boards
- 4 layers110 × 54 mm
- 2 layers100 × 100 mm
Mist1010
UzixLS/mist1010-board
10x10cm PCB variant of MIST FPGA project for G738/G706 enclosure
271 parts43MIT - 2 layers100 × 100 mm
Zxuno1010
UzixLS/zxuno1010-board
10x10cm PCB variant of ZX-UNO project for G738/G706 enclosure
231 parts23MIT - 2 layers178 × 145 mm
Ultra DB X51 v1
ExploreEmbedded/8051_DevelopmentBoard
Design files and sample code for 8051 development Ultra Boards
145 parts70 - 2 layers104.7 × 55.6 mm
Lab1
jsjolund/dmx512-controller-board
Controller board for DMX512 compatible devices, built around the STM32F4 processor
96 parts26 - 4 layers100 × 80 mm
- 2 layers
Questions
How big is the Hw11c PCB?
It measures 49 × 27.5 mm and has 2 copper layers, 1.6 mm thick.
What parts does the Hw11c use?
89 parts, built around the LPC11C14FBD48/301, MCP2551-I/P, TJA1055T/C and BC817. The full list of its parts is on this page, with links to each part's symbol and footprint where PCBKit's library has them.
Where can I download the Hw11c KiCad files?
From the igkov/bcomp11hw repository on GitHub, at the commit this page was made from: the board is hw11c.kicad_pcb. PCBKit opens the board in the browser, with nothing to install.
Can I use the Hw11c design in my own project?
Its repository publishes it under the MIT licence: you may reuse it on that licence's terms (keep the author's notice, and for a copyleft licence share your changes alike).